The BOD, of a municipal wastewater is 200 mg/L at 20°C. The amount of organic matter remaining in the sample after 5 d is equivalent to 151.93 mg/L of O,. Calculate the BOD, of the sample at 30°C. Use 0 = 1.047 as the Arrhenius coefficient for BOD rate constant. %3D 8,

The BOD, of a municipal wastewater is 200 mg/L at 20°C. The amount of organic matter remaining in the sample after 5 d is equivalent to 151.93 mg/L of O,. Calculate the BOD, of the sample at 30°C. Use 0 = 1.047 as the Arrhenius coefficient for BOD rate constant. %3D 8,

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For a wastewater sample, the three-day biochemical oxygen demand at incubation temperature of 20°C…

A: Given data- BOD at 3 days at 20o=200 mg/Lk=0.22 day-1To Find-BOD at 5 days at 20o

Q: It takes 22 hours for water to flow from point A to Point B in a river. The flow rate and BOD5 in…

A: Given data :-Time (t) = 22 hours (for water to flow from point A to B in a river)* flow rate =20…

Q: If 2% solution of a sewage sample is incubated for 5 days at 20 degrees and depletion of oxygen was…

A: Given data, Percentage of sewage sapmle solution= 2% Dissolved oxygen, At 20°c = 5PPM Bod5=?

Q: A settling tank having a depth of 3.5 m and surface area of 1000 m2 is used to remove particles of…

A: Given: Depth of tank, H = 3.5 m Surface area, A = 1000 m2 Particle size, d = 0.01 mm Specific…

Q: A water treatment plant treats 6000 m3 of water per day. As a part of the treatment process,…

A: Given : Discahrge (Q)=6000 m3/dayOver flow rate (O.F.R)=1.5 m/hrDepth (h)=3 m

Q: In an activated sludge treatment system, the BOD concentration decays according to first order…

Q: e moisture content of a sludge is 95% with a volume of 1000 m3. If the volume of dewatered dge is…

Q: Determine the exact and approximate alkalinity of a water sample that contains 120.0 mg/L of…

Q: 4. (Modified from problem in an FE Review Book) A municipal wastewater treatment plant is…

A: Given Data:Ultimate BOD of Mix L=8.2mg/l.Initial D.O Deficit =2.4mg/lSaturation…

Q: Calculate phosphorus in units of kg/ha.

A: Given data: Density of soil(ρ)=1.3 g/cc Density of soil(ρ)=1.3*10^6 g/m^3 Density of soil(ρ)=1300…

Q: 21. Determine the biomass concentration of the activated sludge system based on the following…

Q: The moisture content of a sludge is 95% with a volume of 1000 m3. If the volume of dewatered sludge…

Q: The BOD, of a municipal wastewater is 200 mg/L at 20°C. The amount of organic matter remaining in…

Q: Calculate chloride (mg/L as CF) content of the water sample.

Q: 3. Table below shows the concentration of dissolve oxygen for a BOD test, diluted by 100. Time…

A: The given data is: Dilution Factor (DF)= 100 Time (days) Diluted sample DO (mg/l) 0 7.95 1…

Q: One litre of sewage, when allowed to settle for 30 minutes give a sludge volume of 64 cm3. If the…

Q: SALINITY DETERMINATION BY MOHR METHOD Q1: Compare and contrast chlorinity and salinity. Q2: What…

Q: A sedimentation tank of dimensions 33m x 12m x 6m is filtering wastewater at a flow rate of 0.3…

A: Given: Length, L = 33 m Width, B = 12 m Depth, H = 6 m Flow rate, Q = 0.3 m3/s Density of particles,…

Q: Domestic wastewater has a reaction rate coefficient of 0.3 1/d at 20° C. The ultimate BOD of the…

Q: The concentration of dissolved oxygen in a sample of waste water decreases from 9 x 10^3 g/L to 6.2…

A: Given data, Initial Concentration of DO = 9×103 g/l Final Concentration of DO = 6.2×103 g/l Number…

Q: Estimate sludge production (Px) based on the following conditions: microbial decay coefficient (kd)…

A: Given Influent fow= 1m3/s Q=1000 liter/s Q=10001×24×60×60 liter/day=86.4×106 liter/dayQ=86.4 MLD…

Q: 100 m³ of sludge holds a moisture content of 95%. If its moisture content changes to 90%, the volume…

A: given- volume V1=100 m3moisture P1=95%moisture P2=90%

Q: Using kinetic equation, estimate effluent soluble BOD concentration based on the following…

A: Expression of Effluent soluble BOD concentration (S) is given by: S=Ks×1+Kd×QcQcμm-kd-1where,Ks =…

Q: A laboratory provides the following analysis obtained for a wastewater sam Total Solids = 200 mg/L…

A: GIVEN DATA:- TOTAL SOLIDS OF SAMPLE=200 MG/L TOTAL SUSPENDED SOLIDS OF SAMPLE=160 MG/L FIXED…

Q: If the BOD3 of a wastewater sample is 75 mg/l and reaction rate constant k (base e) is 0.345 per…

Q: If 19.3mL of the standardized Na2S2O3 solution was used in determining the DO, what is the DO…

A: 0.01 N Na2S2 O3 is used in titration to decolorized the blue solution and the volume of 0.01N Na2S2…

Q: The BOD, of a municipal wastewater is 200 mg/L at 20°C. The amount of organic matter remaining in…

Q: (a) What is the maximum contaminant concentration that is expected at a location 2 km downstream of…

A: a) - Discharge(Q) = 2m3/s B= 5m D= 1m Velocity = QB*D V= 25*1 = 0.4m/s Time taken to travel…

Q: If the BOD3 of a wastewater sample is 75 mg/I and reaction rate constant k (base e) is 0.345 per…

Q: 17. A section of a homogeneous earth dam is shown in Fig. 20.36. Calculate the seepage discharge per…

A: Given:- A section of a homogeneous earth dam is given The coefficient of permeability of the dam…

Q: Trickling filter is a fixed-bed biological reactor that operates under aerobic conditions. It is…

Q: Using the data in the following table, (1) to find the volume required for the equalization tank,…

A: Given,

Q: cyclone has a dpc of 5 µm, what is the overall removal efficiency for air stream that has the…

A: Given dpc=5 µm

Q: Samples of water are tested for total dissolved solids (TDS). TDS is normally distributed. The…

A: Given Data:TDS2480 2440 2400+34 2360+37 2320Frequency2335402221

Q: A 2% solution of a sewage sample is kept at an incubation temperature of 20°C. If initial DO…

A: BOD = (DOinitial -DOfinal)*(Dilution factor) DOinitial = 8.5mg/l DOfinal = 5.5mg/l Dilution factor…

Q: Ex 12.2: water with electrical conductivity 1.5 mmhos/cm is used to irrigate crop of 135 cm seasonal…

Q: Water quality and characteristics discuss: 1. Organoleptic parameters 2. Nitrate 3. Solids

A: 1) Organoleptic Parameters- These are defined as the parameters in which results are obtained after…

Q: What will be the Sludge Volume Index (SVI) if 100 ml of sludge collected in 30 mins on drying weighs…

A: Given data- Volume of settled sludge=100 mLtime t=30 mindry weight MLSS=800 mgTo Find-Sludge volume…

Q: After mixing during coagulation or flocculation process followed by 15 min settling, why do we…

A: The question is about the coagulation and flocculation. Coagulation and flocculation is used for…

Q: A wastewater has the following composition in g/m. COD - 370 BOD - 496 Find the ratio COD/BOD. If…

A: Bio-chemical oxygen demand(BOD)- It is the measure of the quantity of oxygen required for oxidation…

Q: For a wastewater sample, the three-day biochemical oxygen demand at incubation temperature of 20°C…

Q: 1. A wastewater treatment plant uses a circular sedimentation basin to treat 3.1 MGD of domestic…

A: 1) Detention time = Total volume of tank/ discharge

Q: Using kinetic equation, estimate sludge age (SRT) based on the following conditions: saturation…

Q: 1. In a total solids determination on a 100 ml sample of river water the following results were…

A: My dear, We are given with Weight of empty dish after firing Weight of dish + weight of dry…

Q: what concentration in moles per liter was made by combining 0.328 g Na3PO4 with 1.00L water?

Q: A city of 20,000 people disposes of 1.05 m3/s of treated sewage that still has an ultimate BOD of…

A: population 20000 finding oxygen deficit below

Q: In a BOD test, the amount of organic matter remaining in the wastewater was measured at certain time…

A: Finding out ultimate BOD and BOD rate constant k.

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

i need the answer quickly

Example
The BOD, of a municipal wastewater is 200 mg/L at 20°C. The amount
of organic matter remaining in the sample after 5 d is equivalent to
151.93 mg/L of O,. Calculate the BOD, of the sample at 30°C. Use 0 =
1.047 as the Arrhenius coefficient for BOD rate constant.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the BOD of a municipal wastewater at the end of 7 days is 60 mg/L and the ultimate BOD is 85.0 mg/L, what is the first order reaction constant?
Suppose 1 m3 of an aquifer is contaminated with toluene.Groundwater moves through at an actual speed of 0.03 m/day and the toluene has a dissolved concentration equal to 20% of its solubility.How long will pump and treat take (in years) to remove the toluene spill?Toluene Conc. 4 LPorosity: 30%
An urban sludge basin has a volume of 500 m3. The basin is initially 64% full. The sludge with a density of 1320 kg/m3 is taken away from the basin at a rate of 4 ton/day. How long will the basin take to be fully emptied? Assume the basin is now initially full and re-estimate the time to empty it completely
If the BOD of a municipal wastewater at the end of 7 days is 60 mg/liter and the ultimate BOD is 85 mg/liter, then the rate constant is ____ per day.
A city of 20,000 people disposes of 1.05 m3/s of treated sewage that still has an ultimate BOD of 28.0 mg/L and 1.8 mg/L DO into a river. Upstream from the outfall, the river has a flow rate of 7.08 m3/s and a velocity of 0.37 m/s. At this point, the ultimate BOD and the DO in the river are 3.6 and 7.6 mg/L, respectively. The saturation value of DO (at the temperature of the river) is 8.5 mg/L. The deoxygenation coefficient is 0.61/day, and the reaeration coefficient is 0.76/day. Assume complete mixing and the velocity in the river is the same upstream and downstream of the outfall. What is the oxygen deficit and the ultimate BOD just downstream from the outfall (just after mixing, before any reaction can occur)?
A landfill that is 12 ha in area has a liner of thickness 0.9 m. Each year 1700 m3 of leachate is collected. The hydraulic conductivity ofthe liner is 3.9 × 10-10 m · s-1. What is the head of water above the liner? Select one: a. 2 m b. 3 m c. 1 m d. 4 m
A lake is fed by a polluted stream and a sewage outfall. The stream and sewage wastes have a decay rate coefficient (k) of 0.9/day (1st order units). Assuming complete mixing and no other water losses or gains, what is the steady-state pollutant concentration as mg/L in the lake?Incoming Stream: C = 10 mg/L, Q = 90 m^3/sSewage Outfall: C = 300 ppm, Q = 0.5 m^3/sLake: V= 10,000 m^3
Domestic wastewater has a reaction rate coefficient of 0.3 1/d at 20° C. The ultimate BOD of the sample is 550 mg/L. What is the BOD remained after incubation at 20° C for 5 days in mg/l?
Determine the exact and approximate alkalinity of a water sample that contains 120.0 mg/L of (CO3)^2- and 75.0 mg/L of (HCO3)^- at a pH of 9.7 at 25 degrees Celcius
Civil, Environmental Laboratory determinations of an industrial wastewater indicate that its ultimate BOD is 750 mg/L and the k value at 20°C is 0.20 day¹. Calculate the 5-day BOD. What would be the 5-day BOD, if k value dropped to 0.1 day ¹?Note: Ultimate BOD=L=L,
A wastewater treatment plant discharges 0.1 m3/s of treated wastewater to a river having a mean flow rate of 25 m3/s. The biological components of the wastewater have a concentration of 15 mg/l in the waste stream and are consumed by bacteria in the river with a rate constant of k = −0.3 d-1. 1. Ignoring the biological reaction, what is the pure physical dilution downstream in the river after the waste discharge is fully mixed across the cross-section of the river?
Drinking water from a dam which undergoes conventional treatment has a computed chlorine demand (due to silt, corrosion and bacteria) amounting to 3.5 ppm. Per PNSDW, such drinking water must have a mandatory chlorine residual of 1.0 ppm at source. If production flow is at 500 cu.m./day, calculate the chlorine dosage needed in pounds per day (PPD).