The bulk head AD is subjected to both water and soil-backfill pressures. The bulk head has a mass of 750 kg . Suppose that Wwater = 113 kN/m and wsoil = 340 kN/m. D 0.5 m 6 m 4 m W. water Weol Part A Assuming AD is "pinned" to the ground at A, determine the x and y components of reaction at A necessary for equilibrium. Express your answers using three significant figures separated by a comma.

The bulk head AD is subjected to both water and soil-backfill pressures. The bulk head has a mass of 750 kg . Suppose that Wwater = 113 kN/m and wsoil = 340 kN/m. D 0.5 m 6 m 4 m W. water Weol Part A Assuming AD is "pinned" to the ground at A, determine the x and y components of reaction at A necessary for equilibrium. Express your answers using three significant figures separated by a comma.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the mixing ratio (w) and saturation mixing ratio (ws) if T=35c and Td=10c. Assume p=1 atmosphere (1013.25 hPa. Use temperature appropriate values of lv.
It is desired to pump ethanol at 20 ° C through 25 m ofstraight smooth tubing under laminar-fl ow conditions,Re d = ρ Vd / μ < 2300. The available pressure drop is10 kPa. ( a ) What is the maximum possible mass fl ow, inkg/h? ( b ) What is the appropriate diameter?
A Horizontal Capillary Tube (Radius 10 Um) Con- Tains An Oil/Water Interface. The Pressure In The Oil Phase Is 14.5 Psi (100 KPa). Determine The Pressure In The Water Phase If The Contact Angle Is 30° And The IFT Is 30 Dynes/Cm (30 MN/M).
Show complete solution pls SN = 93
The cylindrical water tank in Fig. is being fi lled ata volume fl ow Q 1 = 1.0 gal/min, while the water alsodrains from a bottom hole of diameter d = 6 mm. At timet = 0, h = 0. Find and plot the variation h ( t ) and the eventualmaximum water depth h max . Assume that Bernoulli’ssteady-fl ow equation is valid.
Make an analysis of the shape h ( x ) of the water–air interfacenear a plane wall, as in Fig. , assuming that theslope is small, R - 1 ≈ d 2 η / dx 2 . Also assume that the pressuredifference across the interface is balanced by thespecifi c weight and the interface height, ∆p ≈ ρ g η . Theboundary conditions are a wetting contact angle θ at x = 0and a horizontal surface η = 0 as x--->∞. What is themaximum height h at the wall?
The system in Fig. consists of 1200 m of 5 cm castiron pipe, two 45° and four 90° flanged long-radius elbows,a fully open flanged globe valve, and a sharp exit into areservoir. If the elevation at point 1 is 400 m, what gagethe pressure is required at point 1 to deliver 0.005 m3/s of waterat 20°C into the reservoir?
Q 244 What are the reaction forces on the latch an djoint in the gate below? And in case thefloodgate is reversed (concave)? *The gate is a cylinder room with length L = 5 m
The swept volume of the reversible diesel engine is 0.198 m^3/s and the mean effective pressure is 10 bar. Determine the break power of the engine if mexhanical effucuency if the engune is 70 %.
The system consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water into the reservoir? Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kvalve = 6.9 f = 0.0316 γ = 9810 N/m3 Choices: 3.44 Mpa 1.02 MPa 3.48 Mpa 1.00 MPa None of the choices
Déterminer la différence de pression Pa-Pb pour D1=330mm D2=160mm d3=480mm D4=230mm. Le poids spécifique de l'air est négligeable. Le poids spécifique de eau=9790N/m3Determine the pressure difference pa-pb for d1=330mm d2 =160mm d3=480mm d4=230mDetermine the hydrostatic force exerted on the door AB of dimensions (1m and 0.9m wide) and its point of application Q (distance between A and Q). the specific weight of water is 9790N/m3 and the density of the oil is 0.82m. the specific weight of air is negligible. the specific weight of water is 9790N/m3.
In the figure, the cylindrical capacitor, connected to a constant voltage source Vo= 80 V, rests with its edges on the surface of the water of density ρ=1000 kg/m3 . The distance d=0.4 cm between the condenser armatures is much smaller than its radius half. Find the height "h" at which the water level is established between the reinforcements of the condenser. Neglect capillary phenomena. (k=9•109N•m2/C2,κ=81,g=9.8m/2)