The car A has a forward speed of 22 km/h and is accelerating at 3.7 m/s². Determine the velocity and acceleration of the car relative toobserver B, who rides in a nonrotating chair on the Ferris wheel. The angular rate = 3.4 rev/min of the Ferris wheel is constant.R 9.6 mAnswers:VA/B = (aA/B = (ii22= 3.4 rev/minB51i+ ii+ ij) m/sj) m/s²

The given figure is shown below:

The car A has a forward speed of 22 km/h and is accelerating at 3.7 m/s². Determine the velocity and acceleration of the car relative observer B, who rides in a nonrotating chair on the Ferris wheel. The angular rate 2 = 3.4 rev/min of the Ferris wheel is constant. R= 9.6 m Answers: VA/B( i aA/B = i 22=3.4 rev/min B 51 i+ i i+ i j) m/s j) m/s²

The car A has a forward speed of 22 km/h and is accelerating at 3.7 m/s². Determine the velocity and acceleration of the car relative observer B, who rides in a nonrotating chair on the Ferris wheel. The angular rate 2 = 3.4 rev/min of the Ferris wheel is constant. R= 9.6 m Answers: VA/B( i aA/B = i 22=3.4 rev/min B 51 i+ i i+ i j) m/s j) m/s²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The wooden block (mass m = 0.5358 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle θ = 47.2°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block.NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
The 5-kg ball A revolves at a constant speed ? in a horizontal circle as shown in Figure Q2. If ? = 50° and ? = 7.9m. Explain how r and the mass of the ball should be adjusted if the speed of the ball is to be increased.
At the instant θ = 30 degrees, the 10 Kg slender bar of length L =0.9 m has a clockwise angular velocity of 2.5 rad/s. The coefficient of kinetic friction at end B is 0.22; end A is attached to a massless roller that rolls on the smooth horizontal plane. Answer the following, 1) find the angular acceleration 2) Reaction forced at A and B 3) horizontal and vertical components of acceleration of the rod's center of mass
A 500 N block is resting on an inclined plane and is subjected to a constant force of 600N acting parallel to the inclined plane. After the block has moved 3 m from rest along the inclined plane the force 600N is removed. The inclined plane has a slope of three vertical to four horizontal. Coefficient of friction is 0.20 a. Which is the following gives the distance that the black will move further along the inclined plane until it will stop? b. Which of the following gives the velocity of the block when this for 600 Newton was removed? c. Which of the following gives the velocity of the block when it returns to its initial position?
If the body starts from rest at A and slides 200 ft down the 30° incline, how far will it then move along the other incline? What will be the velocity when it returns to B? Coeff fr= 0.20. please use energy-work method.
The angular velocity of rod OB varies as tetha = 8 - 12t^2 rad/s where t is in seconds. Compute the magnitude of the acceleration of point B at (a) t = 0; and (b) t= 1.0s.
For equation 1, RB+RA=1500. So how did you get RB=2580-50700, RB=-48120 lb ? Also for moment at point B, if 1500 lb-ft is clockwise. How is it positive in moment at point B?
A motor gives gear A an angular acceleration of (2t3) rad/s2, where t is in seconds. If this gear is initially turning at 10 rad/s. The angular velocity of gear B when t = 2.6 s is
An open vessel 4.0m wide, 5.0m long and 3.5m deep contains 3m of water. It is then accelerated to the right along its width. a. Calculate the acceleration just about water to spill. b. At this rate, what is the force (in N) causing the acceleration if the mass of the vessel if the mass of the vessel is 600kg? c. Consider the same vessel accelerated at 7.00 m/s2. Determine the volume (in m3) of water spilled at that acceleration.
1-Moment of inertia of the pulley (kg.m2) ? 2-tension in rope of m1 (N) ? 3-tension in rope of m2 (N) ? 4-angular acceleration of the pulley (rad/s2) ? 5-acceleration of block m1(m/s2) ? 6-acceleration of block m2 (m/s2) ?
A 18kg box is pulled along a horizontal surface by a force F of 50N , which is applied at a 30 degree angle . We assume a coefficient of kinetic friction of 0.4. Draw the free body diagram for the box and calculate the acceleration and the magnitude of the upward force FN exerted by the table on the box .
Water enters a large rigid tank steadily at a rate of V . = 0.5 m3/s, and exits through a large rectangular opening through which the velocity changes linearly in the vertical direction from 4 m/s to 5 m/s. Knowing that the tank is full, determine the magnitude of the velocity through the circular opening at the top whose diameter is D = 15 cm.