The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is O.04 in. Determine the maximum allowable value of P in kips. 0.75 in A B 50 kips 3 in 20 in- 30 in-

The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is O.04 in. Determine the maximum allowable value of P in kips. 0.75 in A B 50 kips 3 in 20 in- 30 in-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Of the following solid shafts diameter, which is the smallest that can be used for the rotor of a 6 hp motor operating at 4500 rpm, if the maximum shear stress for the shaft is 8500 psi?A. 5/16 inB. 3/8 inC. 1/2 inD. 1 in
A hollow tube ABCDE constructed of monel-metal is subjected to five torques acting in the directions shown. The tube has an outside diameter d2= 1.0in. The allowable shear stress is 14,950psi and the allowable rate of twist is 2.45degree/ft. Determine the maximum permissible inside diameter d1 of the tube in inches. Use G= 9500ksi.
Two identical steel [E = 200 GPa] pipes, each with a cross-sectional area of 2800 mm2, are attached to unyielding supports at the top and bottom, as shown. At flange B, a concentrated downward load of P = 240 kN is applied. Determine the normal stress in the upper pipe (1).
5.Compute the maximum shearing stress developed in a phosphor bronze spring having a mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. Assume G = 42 GPa. Use Wahl formula.
Give me right solution A solid cooper red brass C83400 shaft with a diameter of 80 mm is inserted concentrically inside asteel (stainless 304) tube. Determine the inner diameter (in mm) of the tube so that there is no contact pressurebetween shaft and tube, even though the cooper supports an axial compression force of 400 kN.
The beam seciton shown below has moment of inertia about its neutral axis: I = 301.3 (10 -6)m 4 , and if this section is under a bending moment of 22 kN m, please calculate the normal stress at Point B: ____ MPa. Calculate your answer to 1 decimal place.
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.50 in. and a wall thickness of 0.201 in. is fastened to a solid 2.00-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=19 kips, Q=13 kips, L1=7 ft, L2=9 ft, and L3=9 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
An eccentric load is applied at a point 22 mm from the geometric axis of a 60-mm-diameter rod made of a steel for which σY = 250 MPa and E = 200 GPa. Using the allowable-stress method, determine the allowable load P. Take the effective length L = 1.4 m. (Round the final answer to one decimal place.)
The column is constructed from high-strength concrete and A-36 steel reinforcing rods. If it is subjected to an axial force of 30 kips, determine the average normal stress in each rod (ksi). Each rod has a diameter of 0.58 inch. Esteel = 29 x 103 psi and Econcrete = 4.2 x 103 psi, r = 4 inches
Determine the adequacy of a 600 mm diameter (internal) steel pipe of length 2500 m with a thickness of 20 mm if it is capable of carrying a maximum stress of 125 MPa. The pipe is connected to a reservoir whose water surface elevation is at elevation 200 m. and discharge freely into air. A valve at the lower end of the pipe (elev. 0 m) is to be closed quickly. Cwfor Hazen-William’s Equation is 120 for the pipe and take bulk modulus of the water equal to 2.07X106 KPa while modulus of elasticity for steel is 200,000 MPa.
Determine the adequacy of a 600 mm diameter (internal) steel pipe of length 2500 m with a thickness of 20 mm if it is capable of carrying a maximum stress of 125 MPa. The pipe is connected to a reservoir whose water surface elevation is at elevation 200 m. and discharge freely into air. A valve at the lower end of the pipe (elev. 0 m) is to be closed quickly. Cwfor Hazen-William’s Equation is 120 for the pipe and take bulk modulus of the water equal to 2.07X106KPa while modulus of elasticity for steel is 200,000 MPa.
A helical spring composed of 20 turns is fabricated by wrapping wire 10mm in diameter around a forming cylinder 150mm in diameter. Compute the maximum load that the spring can carry if the total elongation is limited to 90mm and the allowable shearing stress is 90 MPa. G=28 GPa.