Answered: The coefficient of linear expansion of…

The coefficient of linear expansion of steel is 1x10-5/°C. How much expansion should engineers anticipate in a 2,000 feet steel bridge if it undergoes a change in temperature from 0°C to 30°C?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter14: Material Selection

Section: Chapter Questions

Problem 8ETSQ

See similar textbooks

Related questions

Q: Q.2. Suppose that Eutectoid steel and 4340 alloy steel are welded between themselves. The heat-…

A: Microstructure analysis : 1) Optical Microscopy : Mechanical grinding and polishing, accompanied by…

Q: copper tubes 0.20cm thick. The three tubes are joined together at their ends. What is the maximum…

A: Given : 1. Outside Diameter(D1) = 3cm 2. Thickness (t) = 0.25cm 3. Inside Diameter (D1) = D2-2t =…

Q: An aluminum pipe has a length of 64 m at a temperature of 15°C. An adjacent steel pipe at the same…

A: Length of the aluminium pipe, Lu = 64m Temperature, To = 15°C Length of steel pipe,…

Q: Glycerine (specific weight 1260 kg/m3, dynamic viscosity 8.00 x 10-2 kg-s/m²) is spread freely to a…

Q: A l-m long steel bar (E = 200 GPa) of 10x10mm dimension fixed at one end and the other end having a…

A: By Hooke's law, stress is directly proportional to strain. Stress = strain * young modulus of…

Q: A 1.8 m dia. by 2.7 m high closed cylinder is fully filled with glycerin having sp.gr. of 1.6 under…

A: d=1.8m h=2.7m

Q: 20 kN.m 2 kN/m A- 2m -4m -2m- Which of the following best describes the elastic curve (deformed…

A: Finding out deformed shape of the beam.

Q: An aluminum pipe has a length of 53 m at a temperature of 7°C. An adjacent steel pipe at the same…

Q: For an assembly shown below, determine the stresses in each rod after a temperature rise of 30°C.…

A: Given:- Properties of barBronze Length=1.2 m=1200 mm C/S =1400 mm2…

Q: A piece of steel is said to have Young’s modulus of 29 × 106 psi. Based upon a yield strength of…

A: I

Q: A cylindrical boiler with an outside diameter of 3.60 m and a wall thickness of 40 mm is made of a…

A: Given data in question Yielding stress FOS Diameter Thickness

Q: An aluminum block (SG=2.5) has a dimension of 0.24 m x 0.24 m xh meters. It is floating in mercury…

Q: Water from a reservoir flowing through a deformable 600mm diameter pipe with a velocity of 2.5m/s is…

Q: In shown figure the aluminum is subjected to a thermal stress where T₁ is 21.957 deg. C and T2 is…

Q: An aluminum pipe has a length of 50 m at a temperature of 6°C. An adjacent steel pipe at the same…

A: Concept Initial length = L1 at temperature T1 Due to temperature change to T2 length of the…

Q: a) What is the final length of a 50-mm-long bar of copper, 10 mm in diameter, stressed by a 500-kg…

Q: As the pellet is about to be released, what is the total elongation (mm) of the rubber? O204 072 O…

A: Total Unstretched length of rubber , L = 60 mm a= 100 mm b = 40 mm TO determine : Total elongation…

Q: A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of a cast iron 5 mm thick.…

Q: Compute the value of EIy at midspan for the beam loaded as shown.

Q: PROBLEM 5 A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of a cast iron 5 mm…

Q: A l-m long steel bar (E= 200 GPa) of 10x10mm dimension fixed at one end and the other end having a…

Q: An aluminum pipe with a length of 60 m at a temperature of 10°C rests freely on the ground. An…

Q: A 4-m-long steel plate with a rectangular cross section (10 mm * 50 mm) isresting on a frictionless…

A: Solution: Given Data Length of a steel plate=4 m Rectangular cross section=10 mm ×50 mm= 0.01 m×0.05…

Q: An aluminum pipe has a length of 52 m at a temperature of 6°C. An adjacent steel pipe at the same…

Q: 1. Copper bar shown calculate the stresses when the temperature drop from 85 °C to 50 °C. a =…

A: *Multiple questions* As per our guidelines we are supposed to answer?️ only one question. Kindly…

Q: etermine the elongation and energy absorbed by a steel bar of ∅15 mm and length of 1 m, when…

A: Deformation : It refers to an object's alteration in size or shape. The actual alteration in the…

Q: At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown in the…

Q: A 1-m long steel bar (E = 200 GPa) of 10 x 10 mm dimension fixed at one end and the other end having…

Q: A cylindrical specimen made of annealed 4135 steel has a diameter of 16 cm and is 12 cm high

A: A type of elastic collision in which two objects of equal mass initially move in the same direction…

Q: The 40 ft. long steel rails on the train track are placed such that there is a small gap, 8, between…

A: Axial tension force is the force acting on rails in its axial direction. It's a pulling force that…

Q: A copper cylinder 4in. inside diameter has walls 1in. thick. End plates are stayed by a 1in.…

Q: An aluminum pipe with a length of 60 m at a temperature of 10°C rests freely on the ground. An…

Q: 3 m STEEL A = 600 mm² E = 200 GPa L = 4 m 2 m ALUMINUM 2 A = 900 mm E = 70 GPa L = 3 m 120 kN 1 m

A: Assuming reaction at steel rod as Rs whereas for aluminium rod as Ra and at pinned support as Re.…

Q: If it is constrained between two supports A and B and is stress-free at 20 ℃, what would be the…

Q: 100 kg block has a coefficient of friction 0.30. Solve for the friction force between A and B.

Q: . A 2-m long aluminum pipe at 27°C is heated until it is 2.0024 m at 77°C. What is the coefficient…

A: What is the coefficient of linear expansion of aluminum?

Q: Steel rails on a train track are laid with a small gap between them at a temperature of -25 F. The…

A: The given data is shown below: T1=-25°FT2=95°FT3=110°FArea of cross-section=5 in.2Length=40ft

Q: An aluminum block (SG=2.5) has a dimension of 0.29 m x 0.29 m xh meters. It is floating in mercury…

Q: tape gap of 0.01cm on each side as shown in the following figure. A lubricant of dynamic viscosity…

A: Given:- t=0.015cm width=1.00cm dynamic viscosity=0.021Ns/m2 F=7.5N To find:- maximum speed

Q: 60 mm

A: Given data:

Q: An aluminum pipe has a length of 54 m at a temperature of 10°C. An adjacent steel pipe at the same…

Q: Steel crane rails of the MRT are laid with their adjacent ends 3.20 mm (change the unit in 3.2 m in…

A: Given data in question Length Spacing Initial temperature Final temperature Coefficient of…

Q: A support column that is pinned at one end and fixed at the other is to be used to support a 12000-…

Q: An aluminum pipe has a length of 69 m at a temperature of 8°C. An adjacent steel pipe at the same…

A: Given, Length of aluminium pipe, Ls= 69m Initial temperature = Ti= 8°C Coefficient of thermal…

Q: 2; a=9.6x10^-6/°F] bar with a width o

A: Given data Change in temperature=380-60=320oF Draw the free body diagram

Q: A steel penstock 500 mm in diameter has shell thickness of 10 mm. The modulus of elasticity of the…

Q: The assembly composed of 3 materials as shown is subjected to equal axial forces at B and C. If A…

A: 0 Structure is determinate

Q: A steel [E = 30,500 ksi; a = 6.6 x 10-6/°F] pipe column (1) with a cross-sectional area of A₁ = 5.50…

Q: Determine the thermal shock resistance for a tool steel with the following properties: tensile…

Question

6. The coefficient of linear expansion of steel is 1x10-5/°C. How much expansion should engineers anticipate in a 2,000 feet steel bridge if it undergoes a change in temperature from 0°C to 30°C?

Complete FBD, FORMULA, AND SOLUTION

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
A steel pipe having a length of 3 ft, an outside diameter of 5 in., and a wall thickness of 1/2 in. is subjected to an axial compression of 50,000 lb. Assuming a modulus of elasticity of 30 * 106 psi and a Poisson’s ratio of 0.27, finda. the shortening of the pipe,b. the increase in the outside diameter, andc. the increase in the wall thickness.
A round vertical steel tank has an inside diameter of 3 m and is 6 m in height. It contains gasoline with a density of 750 kg/m3 . If the allowable tensile stress is 25 Mpa, find the minimum thick required. A. 2.65 mm B. 2.85 mm C. 3.65 mm D. 1.82 mm Please solve ellaborately and include the Units. Thanks!
If it is constrained between two supports A and B and is stress-free at 20 ℃, what would be the stress in the two materials when it is heated to 70 ℃, For Steel: Es = 210 GPa, Coefficient of expansion = 12x10^6/℃. For Brass: Eb = 105 GPa, Coefficient of expansion = 19x10^-6/℃
A steel rod Is stretched two rigid walls and carries a tensile load of 6000 N to 20 degrees Centigrade. Coefficient of thermal expansion is 11.7 x l0^-6 /deg.C and modulus of elasticity 200000 MPa.1. Which of the following gives the minimum diameter of the rod if the allowable stress is not to exceed 140 MPa at -25°C. a. 15 mmb. 17 mmc. 16 mmd. 18 mm2. Which of the following gives the total elongation of the steel rod if it has a length of 1.5m. a. 1.00 mmb. 1.04 mmc. 1.02 mmd. 1.06 mm
A piece of steel is said to have Young’s modulus of 29 × 106 psi. Based upon a yield strength of 36,250 psi, how much can one expect a 325 mm pipe of this material to compress if the pipe has an ID of 2.125 and an OD of 2.625?
In shown figure the aluminum is subjected to a thermal stress where T1 is 21.957 deg. C and T2 is 87.860 deg. C. Determine the required diameter (mm) of the steel rods to limit the expansion of the aluminum just 3.238 mm if the thermal coefficient of aluminum is 24.650 x10^-6 Where: H1 = 2000.392 mm H2 = 2047.231 mm H3 = 1999.692 mm Aal = 2288 mm^2 Eal = 70.018 GPa Est = 202.930 GPa
A railroad track is laid at a temperature of 10℃ with gaps of 0.008 m between the ends of the rails. The rails are 20 m long. Coefficient of thermal expansion is 11.25 x 10-6/℃. Modulus of elasticity = 200,000 MPa. a.) Give the actual deformation of the rails that will result from a temperature of 65℃, b.) Give the corresponding strain due to this deformation, and c.) Give the thermal stress if they are prevented from buckling.
A spherical pressure vessel of 900 mm outer diameter is to befabricated from a steel having an ultimate stress, σ U = 400 MPa.Knowing that a factor of safety of 4 is desired and that the gaugepressure can reach 3.5 MPa, determine the smallest wall thicknessthat should be used.
A structural steel beam 8.00 m long is placed between two rigid supports when the temperature is 15oC at night. 1. Compute the stress developed in the beam when the temperature rises to 41oC during the day? (E = 207 GPa; αT = 11.5x10-6 (oC)-1) 2. Calculate the length change of this beam if the beam was not restrained between supports.
A 25m steel rod with diameter of 20 mm is secured between rigid supports at both ends. If there is no stress at a temperature of 20oC, E = 200GPa.6. Compute the stress when the temperature drops to 0oC, if it has a coefficient of thermal expansion of 0.0000117 m/moC. 7. Compute the strain of the rod if the rod supports yield and move together a distance of 0.5mm as temperature drops.8. Compute the stress in the rod if the supports yield and move together a distance of 0.5mm as the temperature drops.
a)Determine the change in temperature. Indicate increase or decrease in temperature.b)Determine the axial deformation of the steel rod at A (in inches).c)Determine the axial deformation of the steel rod at C (in inches)