A support column that is pinned at one end and fixed at the other is to be used to support a 12000- pound load (P = 12000 lbf). The support is required to be a hollow tube with a length of 3 feet (1 = 12 in.) and an outer diameter of 1.5 inches (d。 = 1.5 in.). Determine the wall thickness of the tube that will maintain a safety factor of 1.8 (n = 1.8) if the material to be used is aluminum (E = 10.4 Mpsi, S, = 60 ksi). do = Ø 1.5 in.

A support column that is pinned at one end and fixed at the other is to be used to support a 12000- pound load (P = 12000 lbf). The support is required to be a hollow tube with a length of 3 feet (1 = 12 in.) and an outer diameter of 1.5 inches (d。 = 1.5 in.). Determine the wall thickness of the tube that will maintain a safety factor of 1.8 (n = 1.8) if the material to be used is aluminum (E = 10.4 Mpsi, S, = 60 ksi). do = Ø 1.5 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A vertical rectangular gate weighs 6000 lbs and is 10 ft tall and 8 ft wide (into the paper). The gate slides in vertical slots in the side of a reservoir containing water. The coefficient of friction between the slots and the gate is 0.03. Determine the minimum vertical force required to lift the gate when the water level is 4 ft above the top edge of the gate. [Answer in units of lbs.]
Two square gates close two openings in a conduit connected to an open tank of water as shown. When the water depth, h, reaches 5 m it is desired that both gates open at the same time. Determine the weight of the homogeneous horizontal gate and the horizontal force R acting on the vertical gate that is required to keep the gates closed until this depth is reached. The weight of the vertical gate is negligible, and both gates arehinged at one end as shown. Friction in the hinges is negligible.
A billboard 3m high by 4m wide is supported as shown in the figure. The totl weight of the billboard is 30 kN. H = 1.5 m and tetha= 60 degrees. Wimd pressure, q= 1.6 kpa Wind pressure coefficient = 1.0. Determine the reactions at the support.
Determine the magnitude of the projected component of the F = 120 lb force acting along the axis BC of the pipe. Suppose that a = 7 ft and h = 2 ft. Express your answer to three significant units and include the appropriate units
A minimum force of P = 50 lb is required to hold the cylinder from slipping against the belt and the wall. Determine the weight of the cylinder if the coefficient of friction between the belt and cylinder is μs = 0.3 andslipping does not occur at the wall.
The 600-lb, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude of the hydrostatic force acting on the gate using the HYDROSTATIC PANEL EQUATIONS. Express your answer in kips. B. Determine the minimum force P required to open the seawater gate. Express your answer in kips.
Solve using the spefic weight of water which is 62.4 lb/ft^3
A flat plate is used to seal an opening in a large water ( y = 62.4lb/ft^3) tank. determine the magnitude of the resultant force R exerted on the plate by the water pressure and the location of the center of pressure with respect to the bottom of the opening if d = 15 ft, h = 5 ft, and b = 5 ft.
Give me right solution according to the question Calculate the pressure P1 and P2 in the structure given in the figure? su=water
Computer Problem The cross section of a concrete dam is as shown. For the dam section of 1m width, plot the magnitude of the resultant of the reaction forces exerted by the ground on the base AB of the dam and the resultant of the pressure forces exerted by the water on the face BC of the dam as function of the depth d of the water for 0<d<24ft. The specific gravities of concrete and water are 150 lb/ft^3 and 64.2 lb/ft^3 respectively. please help with my computer problem in statics . appreciate your time and explanation
The system in the figure is at 70°C (SG = 0.983). Determine the pressure at point C.
Choose the correct answer The pressure gradient is e. Both d and e a. ∇*p c. ∇.p c. ∂p/∂y b. ∇p d. ∂p/∂x