The collar is released from rest in the position shown and slides down the fixed rod. Calculate (a) the stiffness k of the spring (which has been initially pre- compressed 50 mm by the light strap and wires) so that its maximum additional deflection equal 190 mm. (b) The nomal force N between the rod and the collar at the end position. U=AT

The collar is released from rest in the position shown and slides down the fixed rod. Calculate (a) the stiffness k of the spring (which has been initially pre- compressed 50 mm by the light strap and wires) so that its maximum additional deflection equal 190 mm. (b) The nomal force N between the rod and the collar at the end position. U=AT

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.48P: Find the smallest distance d for which the hook will remain at rest when acted on by the force P....

See similar textbooks

Similar questions

The collar is released from rest in the position shown and slides down the fixed rod. Calculate (a) the stiffiness k of the spring (which has been initially pre- compressed 50 mm by the light strap and wires) so that its maximum additional deflection equal 190 mm. (b) The nomal force N between the rod and the collar at 10 kg 190 the end position. Uj-2= AT
The block B start from rest and slides on the 30 wedge A , which is supported by a horizontal surface . Neglecting friction
The uniform slender rod of length l = 260mm is released from rest in the dashed vertical position. With what speed does end A strke the 34 degree incline? Neglect the small mass and friction of the end rollers.
The velocity of the 8-kg cylinder is 0.3 m∕s at a certain instant. The speed v after dropping an additional 1.5 m is 2.5 m/s. The mass of the grooved drum is 12 kg, its centroidal radius of gyration is k = 210 mm, and the radius of its groove is ri = 200 mm. The frictional moment at O is a constant 3 N∙m. Find the frictional force.
In a porter governor the mass of the central load is 18 kgand the mass of each ball is 2kg. the top arms (254) mm while the bottom arms are (304) mm long. The friction of the sleeve is 20 N. If the top arms make 45 deg with the axis of rotation in the equilibrium position, find the range of the speed of the governor in that position
The vertical 2-kg bar AB is attached to the 3-kg cart by a pin at A andthe cord BC. Determine the tension in the cord immediately after the assembly is released from rest in the position shown.
The free length of the spring that is attached to the 0.2-kg slider A is120 mm. If the slider is released from rest when x = 240 mm, calculate its initial acceleration. Neglect friction.
The double pulley shown in the figure is formed by two wheels that are coupled to each other. The complete pulley (formed by the two wheels) has a mass of 15 kg and a turning radius of 110mm. Block A has a mass of 40 kg. If a force of 2 kN is applied to the tied rope of the inner pulley wheel, determine the speed of block A after 3 seconds. At the beginning, the whole system was at rest. Disregard the mass of the string and consider that the moment of inertia (kg.m²) of the complete pulley is given by IP = mko²where m is the mass of the pulley and Ko is the radiusspinning
AB bar, negligible weightmovement on the surface indicated by the wheelsis doing. The bar is at rest when θ = 0°is being released. A and B when θ = 30°Find the velocities of the points.
1)Calculate the velocity of the arm, observed by a stationary person on the ground.2)Draw the FBD of the combined body (crane body, arm and load).3)Is the combined body stable? Why?4)Calculate the moment of the following, about wheel A,i) combined crane bodyii) load mass5)Which combined body’s component(s) will not fail? Why? (Hint: The crane was initially in equilibrium.)6)What are the various limits (maximum or minimum) for the combined body to be stable? Explain why.
Calculate the expected acceleration (Eq. 2) and the experimental acceleration (Eq. 3). This hanging mass will supply the unbalanced (net) force acting on the cart. The track is assumed to be frictionless, so the only force present is that from the hanging mass. m1 (hanging mass), m2 (cart).
The slender rod shown in Fig 1 has a mass m and length L and is released from rest when θ =0°. Determine the horizontal and vertical components of force which the pin at A exerts on therod at the instant θ = 90°. Use normal and tangent coordinates, assume weight in center of rod, from kinematics, we found ω2 = 3g/L