The common instruction set operations can be placed into the following categories: ● Data transfer ● Arithmetic ● Logical Conversion ● 1/0 ● Transfer of control. In the table below, write the name of the instruction set operation category corresponding to each of the given instructions. An example is already given. Answer: Instruction(s) Sub Jump (Branch) XOR Start I/O Multiply Translate Operation Category Arithmetic

The common instruction set operations can be placed into the following categories: ● Data transfer ● Arithmetic ● Logical Conversion ● 1/0 ● Transfer of control. In the table below, write the name of the instruction set operation category corresponding to each of the given instructions. An example is already given. Answer: Instruction(s) Sub Jump (Branch) XOR Start I/O Multiply Translate Operation Category Arithmetic

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

A 32-bit computer has 32 registers, and a memory addressed by bytes with two cycles for reading and writing operations. Consider the instruction ADD, R1, addr. This instruction adds the value stored in R1 to the value stored in the memory address addr, and stores the result in the register R1. a) Show a possible format for this instruction, having into account that the computer has 100 machine instructions and the addresses are represented using 32 bits. b) Indicate the elemental operations and control signals needed to execute the previous instruction.
Consider the following instruction sequence where registers R1,R2 and R3 are general purpose and MEMORY[X] denotes the content at the memory location X. InstructionMOV R1,(5000)MOV R2,(R3)ADDR2,R1MOV (R3),R2INC R3DEC R1BNZ 1004HALTSemanticsR1←MEMORY[5000]R2←MEMORY[R3]R2←R1+R2MEMORY[R3]←R2R3←R3+1R1←R1−1Branch if not zero to thegiven absolute addressStopInstruction Size (bytes)44242221 Assume that the content of the memory location 5000 is 10, and the content of the register R3 is 3000. The content of each of the memory locations from 3000 to 3020 is 50. The instruction sequence starts from the memory location 1000. All the numbers are in decimal format. Assume that the memory is byte addressable. After the execution of the program, the content of memory location 3010 is
17. Consider the following hypothetical instruction: SubMem R1, mem1, mem2 This instruction works as follows: \[ \mathrm{R} 1 \leftarrow \text { [mem1] - [mem2] } \] In a multi-cycle datapath implementation, this instruction will: a. Use the MDR twice b. Use the ALU once c. Use the "shift to left" unit twice d. None of the above Answer: B 18. Consider the following hypothetical instruction: Mems mem1, R1, mem2 This instruction works as follows: \[ \text { [mem1] } \leftarrow \mathrm{R} 1 \text { - [mem2] } \] One of the following is correct about this instruction: a. It will not need theBregister b. It will require priting into MDR twice c. It will require writing into the ALUout three times d. None of the above Answer: A 19. By comparing the hypothetical instructions given in Questions (17) and (18), if we run these instructions on the same processor, then one of the following is correct: a. Both instructions have the same CPI b. Mems executes faster than SubMem c. SubMem executes…
Very urgently needed!! Suppose before the CALL instruction within a code the registers hasfollowing data:SS=1E00H, SP=000AH, CS=85D9H, IP=10B5H, AX =1D02H, CX=04A8Hand DX=6550H.Draw a schematic diagram to illustrate what will happen after the CALLinstruction executes. Note that CALL instruction also stores the value ofregisters AX, DX and CX into the stack segment as they are being used inthe called procedure.
Q:What is the recursive definition and base case for assembly line scheduling with three parallel lines? What is the minimum time taken by the following diagram to assemble a product?Also find an efficient path to assemble a device in minimum time.
The following sequence of instructions are executed in the basic 5-stage pipelined processor OR R1, R2, R3 OR R2, R1, R4 OR R1, R1, R2 a) Indicate the dependencies and their types b) Assume no forwarding in this pipelined processor indicate hazards and NOP instruction to eliminate them. c) Assume there is full forwarding, indicate hazards and NOP instructions to eliminate them
16. The contents of Register (BL) and Register (AL) of 8085 microprocessor are 49H and 3AH respectively. The contents of AL, the status of carry flag (CF) and sign flag (SF) after executing 'SUB AL, BL' assembly language instruction, are a. AL=0FH; CF=1; SF=1 b. AL=F0H; CF=0; SF=0 c. AL=F1H; CF=1; SF=1 d. AL=1FH; CF=1; SF=1
Develop a hypothetical architecture with illustrative instruction and data formats, instruction sets, etc., explain the instruction and machine cycles step-by-step by developing a short program (at least, with two arithmetic operations, three logic operations, three memory or two L/C) operations) and by indicating the corresponding register operations. All architectural, etc., selections must to be justified sufficiently. CAN YOU EXPLAIN WITH THE EXAMPLE USING NUMBERS IN THE STACKS WITH EACH STEP INSTEAD OF PROGRAM.
Question P .Implement and Compute the total memory traffic in bytes for both instruction fetch and instruction execution for the code that implements the expression a=(b*c) d on 3-, 2-, 1-, and 0- address machines. Assume opcode occupy one byte, address occupy two bytes and data values also occupy two bytes. The word length is one byte. Full explain this question and text typing work only We should answer our question within 2 hours takes more time then we will reduce Rating Dont ignore this line
Consider a computer which has a memory which is capable of storing 4096 K words and each word in memory can be of size 32 bits. The computer supports a total of “6” addressing modes, and it has “50” computer registers. The computer supports instructions, where each instruction consists of following fields: Mode Operation code Register Register Memory Address Given that each instruction will be stored in one memory word, discuss with a suitable diagram the format of instruction by specifying number of bits for each field of instruction. Discuss each field of instruction
Explain with a suitable Diagrams the three basic types of Computer Modules in your own words. Using the IAS Instruction Set write the Instruction Type and Description for the following: Symbolic Representation. a) MUL M(Z) b) DIV B(Z) c) JUMP + D(L,20:39) d) STOR A(H,28:39) I don't want to write it by hand
14. Consider the following assembly language instructions:mov al, 15mov ah, 15xor al, almov cl, 3shr ax, cladd al, 90Hadc ah, 0What is the value in ax register after execution of above instructions? a. 0270H b. 0170H c. 01E0H d. 0370H