The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.8 in?, 1.07 in?, and 0.56 in? respectively.Determine the change in length (in inches) of the bar if P = 11280 Ib.The moduli of elasticity are 30092 ksi for steel ,12006 ksifor bronze, and 10002 ksi for aluminum. Round off the final answer to four decimal places. Bronze Aluminum 3 ft Steel ... 4 ft 2 ft 2P 3P 4P

The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.8 in?, 1.07 in?, and 0.56 in? respectively.Determine the change in length (in inches) of the bar if P = 11280 Ib.The moduli of elasticity are 30092 ksi for steel ,12006 ksifor bronze, and 10002 ksi for aluminum. Round off the final answer to four decimal places. Bronze Aluminum 3 ft Steel ... 4 ft 2 ft 2P 3P 4P

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The compound bar ABCD has a uniform cross-sectional area of 0.28 in2.Determine the change in length (in inches) of the bar if an axial force P = 3676 lbis applied.The moduli of elasticity are 29037 ksi for steel and 10006 ksifor aluminum. Round off the final answer to four decimal places.
please sir solve accurate and fast. ( of possible solve compyuterised) THANKS a 30m weighing 0.900kg has a cross-sectional area 0.0485cm^2. the tape measures 30.000m when supported throughout under a tension of 5kg. the modulus of elasticity is 2.1x10^6kg/cm. what tension is required to make the tape measure 30m when supposed only at the two ends?
Q#5: The cross section of a wood beam carries a bending moment M of magnitude 20R lb.-in. acting at 10⁰ to the horizontal. Determine(a)the angle between the neutral axis and the horizontal; and (b) the maximum bending stress acting on the cross section. Note : Use R=980 For Details See Picture Attached
A rectangular steel block 250 mmx100 mmx80mm is subjected to axial loads as follows. 480 kN (tensile in direction of its length) 900 kN (tensile on 250mm x 80 mm faces) 1000kN (comp. on 250mm x100mm faces) taking E=200 GN/m2 and 1/m=0.25 find a). Change in dimensions (height, width and length) b). Change in volume of the block c). Volumetric Strain c). Values of N and K (Module of Rigidity and Bulk Modulus) for material of the block. d). Determine the volume difference if the temperature of block increased by 20K. (Take alpha steel = 11.7 x 10-6 / 0C ) e). Discuss the behavioral characteristic for given application Comparing the impact from given mechanical loadings and thermal loadings to the block.
The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load of 50 kN, determine the change in its strength in mm at section a-a. Est = 200 GPa, vst = 0.29
line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 200 C under a 50 N pull supported at both ends. During measurement, the ttemperature is 50C and the tape is suspended under a 75 N pull. The line is measured on a 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3 mm2 and the coefficient of linear expansion is 0.000016 m/0C. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance.
Tempered rod with length of c= 8m and cross sectional dimensions a=297 mm is carrying an axial load P=75kN if the modulus of elasticity is 185gpa determine the elongation
Q1/A bar 500 mm long and 20 mm in diameter is elongated by 1.2mm under axial pull of 105 kN. Calculate stress and modulus of elasticity of bar.
A tapered rod with length c = 7m and cross - sectional dimensions a = 270n mm and b = 119 mm is carrying an axial load P = 75kN . If the modulus of elasticity of the rod is E = 164GPa , determine the elongation of the rod in mm . Final ans. in 3 dec place
The 919-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 321 mm2. Find the location x (in mm) of P that can be safely applied to the bar if the stresses in AC and BD are limited to 112 MPa and 57 MPa, respectively. Express your answer in two decimal places.
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The steel wide-flange beam has the dimensions shown. If it is made of an elastic perfectly plastic material having a tensile and compressive yield stress of o,, determine the following: Given: Allowable Stress = 300 MPa a = 20 mm b = 250 mm c = 250 mm c. Calculate the plastic moment of the section in kN.m d.Calculate the shape factor of the section.
A beam has a T section, and the loads are shown below. Instruments to measure strain are set in points C and D. Determine the value of load P if the strain in point C is +527x10-6 [mm/mm] (elongation), and at point D, it is -73x10-6 [mm/mm] (contraction). The inertia of the section is 2,000 [cm4] and the elastic modulus is 21x103 [kgf/mm2].