= The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment (1) is a tube with an outside diameter of D₁ = 3.85 in., a wall thickness of t₁ = 0.25 in., and a shear modulus of G₁ = 4,000 ksi. Steel segment (2) is a tube with an outside diameter of D₂ = 2.10 in., a wall thickness of t2 = 0.125 in., and a shear modulus of G₂ = 12,000 ksi. The compound shaft is subjected to torques applied at B and C as shown. Determine the rotation angle of C with respect to the support at A. (1) 9ft -0.0293 rad -0.0233 rad 1,700 lb-ft B (2) 6 ft 650 lb-ft

= The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment (1) is a tube with an outside diameter of D₁ = 3.85 in., a wall thickness of t₁ = 0.25 in., and a shear modulus of G₁ = 4,000 ksi. Steel segment (2) is a tube with an outside diameter of D₂ = 2.10 in., a wall thickness of t2 = 0.125 in., and a shear modulus of G₂ = 12,000 ksi. The compound shaft is subjected to torques applied at B and C as shown. Determine the rotation angle of C with respect to the support at A. (1) 9ft -0.0293 rad -0.0233 rad 1,700 lb-ft B (2) 6 ft 650 lb-ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment (1) is a tube with an outside diameter of Dy = 3.95 in., a wall thickness of t1 = 0.25 in., and a shear modulus of G1 = 4,000 ksi. Steel segment (2) is a tube with an outside diameter of D2 = 2.15 in., a wall thickness of t2 = 0.125 in., and a shear modulus of G2 = 12,000 ksi. The compound shaft is subjected to torques applied at B and C as shown. Determine the rotation angle of C with respect to the support at A.
The post shown, whose cross-sectional area is 100 x 150 mm2, rests at the middle of a circular solid steel plate. The steel plate is placed above a hollow cylinder. Both the steel plate and the cylinder have diameter of 300 mm and a thickness of 20 mm. Solve for the following: a. punching shear stress in the steel plate b. punching shear stress in the hollow cylinder c. bearing stress in the steel plate due to the post d. bearing stress in the cylinder due to the steel plate
A hollow aluminum tube used is a roof structure has an outside diameter d2 and inside diameter d1. The tube is 2.5m long and the aluminum has a shear modulus of G=28 GPa. a.If the tube is twisted in pure torsion by torques acting at the ends,what is the angle of twist in degrees when the max shear stress is 50MPa? b.What diameter “d” is required for a solid shaft to resist the same torque with the same maximum stress? d1 = 90 (mm) d2 = 110 (mm)
Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in. Segment BC is a solid rod of diameter d2. The average normal stresses must not exceed 3400 psi in rod AB and 6500 in rod BC, respectively. Use P1 = 3,650 lb. and P2 = 5,550 lb. a. Determine the smallest allowable value of d1 (in inches). Round-off to 2-decimal places. b. Determine the smallest allowable value of d2 (in inches). Round-off to 2-decimal places.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. If P = 75 kN, determine the following:a. Stress in the bronze segment.b. Stress in the aluminum segment.c. Stress in the steel segment.
The polymer bar shown in the figure below has a width of b=55b=55 mmmm, a depth of d=104d=104 mmmm, and a height of h=274h=274 mmmm. At a compressive load of P=120P=120 kNkN, the bar height contracts by Δh=−2.60Δ⁢h=-2.60 mmmm, and the bar depth elongates by Δd=0.36Δ⁢d=0.36 mmmm. At this load, the stress in the polymer bar is less than its proportional limit. Determine: (a) the modulus of elasticity. (b) Poisson’s ratio. (c) the change in the bar width bb.
PLEASE ANSWER ASAP TY! a) Determine the cross-sectional area of the structural tube (in mm2) b) Determine moment of inertia of the cross-section about the neutral axis (in mm4) c) What is the maximum normal stress at point K (in MPa)? Include negative sign if compressive. d) What is the axial stress at section H-K (in MPa)? Include negative sign if compressive. e) What is the flexural stress at section H-K (in MPa)? f) What is the maximum normal stress at point H (in MPa)? Include negative sign if compressive.
The cross section of the AB part of the welded pipe part given in the figure is a hollow pipe and the cross section of the BC part is a circle with a solid body. The inner diameter of the pipe section is 20mm and the outer diameter is 28mm, while the diameter of the full body part is 12mm. Determine the average normal stress at the D and E points accordingly.
Determine the average normal stress in each rod if T2=400∘F Calculate the new length of the aluminum segment.
An aluminum alloy cylinder (2) is clamped between rigid heads by two steel bolts (1), as shown. The steel [E = 200 GPa; α1 = 11.7 × 10−6/°C] bolts have a diameter of 19 mm. The aluminum alloy [E = 70 GPa; α2 = 23.6 × 10−6/°C] cylinder has an outside diameter of 160 mm and a wall thickness of 9 mm. Assume that a = 700 mm, b = 810 mm, and c = 325 mm. If the temperature of this assembly changes by ΔT = 60°C, determine(a) the normal stress in the aluminum cylinder.(b) the normal strain in the aluminum cylinder.(c) the normal strain in the steel bolts.
A 1 meter long steel rod AB of 15-mm diameter is held snugly (without any initial stresses) between rigid walls by the arrangement shown in the figure. (STEEL ROD : E = 200 GPa , α= 12 x 10-6/°C , and yield strength σY = 250 MPa.) a) If the rod undergoes a temperature drop of 24°C, and the bolt at B is tightened causing the rod to elongate by 0.0566 mm, determine the bearing stress between the washer and the wall. b) Determine the amount of temperature drop that is allowed if the factor of safety against yieldingis 4.
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 265 mm, a wall thickness of 11 mm, and a length of 4.6 m. The pipe supports a compressive load of 640 kN. After the temperature of the pipe drops 35°C, determine:(a) the axial deformation of the pipe.(b) the change in diameter of the pipe.