The compound shaft shown is attached to rigid supports.aBronzeBSteelFor the bronzeFor the steelDiameter = 100mmDiameter = 50mmG= 35GPAG= 83GPASallowable= 45MPASSallowable= 55MPA.Lbr= 2.13a. determine the ratio of the lengths of the bronze and steel so that each material will be stressed to its maximum permissible limitb. determine the maximum torque carried by the bronze.C. what is the relative angle of twist with respect to the support if max torsion is applied at B.

Given, SSbronze = 45 MPa SSsteel = 55 MPa

The compound shaft shown is attached to rigid supports. b. Bronze "B Steel For the bronze For the steel Diameter = 100mm Diameter = 50mm S= 35GPA G= 83GPA ESallowable= 45MPA Sallowable= 55MPA. br= 2.13

The compound shaft shown is attached to rigid supports. b. Bronze "B Steel For the bronze For the steel Diameter = 100mm Diameter = 50mm S= 35GPA G= 83GPA ESallowable= 45MPA Sallowable= 55MPA. br= 2.13

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 200 C under a 50 N pull supported at both ends. During measurement, the ttemperature is 50C and the tape is suspended under a 75 N pull. The line is measured on a 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3 mm2 and the coefficient of linear expansion is 0.000016 m/0C. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance.
A brass (? =5.6 ? 10^6 ???) and aluminum (? = 3.7 ? 10^6 ???) cylinders are bonded together at B, and are attached to fixed supports A and C. Determine (a) The torsion in AB, (b) The torsion in BC, (c) The maximum shearing stress in AB (d) The maximum shearing stress in BC.
Please answer in neat & complete solution. thanks Q: etermine the forces in all bars of the given set of trusses. Tabulate the answers per bar and their forces for every set of trusses. NOTE: Positive value (+) indicates tension and Negative value (-) indicates compression Where: (all units are in kN) P = 33 Q = 9 R = 2
Given Y = 9.79 kN/m^3 Find: P @ bottom of tank (kpa) Force (tensile) on each bolt (kN) Stress on each bolt (MPa)
Determine the stress in the steel and in the wood if the beam is subjected to a moment of 750 lb-ft. Esteel=29,000 ksi Ewood=1600 ksi
The compound shaft shown is attached to a rigid supports. For bronze segment AB, the diameter is 75 mm, maximum shearing stress is 60 MPa, and G = 35 GN/m^2. For steel segment BC, the diameter is 50 mm, maximum shearing stress is 80 MPa, and G = 83 GN/m^2.1. Which of the following most nearly gives the ratio torque carried by bronze to torque carried by steel? a. 1.2b. 1.8c. 1.6d. 2.02. Which of the following most nearly gives the torque carried by the bronze in kN.m?a. 4.98b. 9.15c. 6.53d. 3.143. Which of the following most nearly gives the maximum torque T than can be applied in kN.m? a. 6.4b. 5.1c. 4.3d. 7.8
Solve this Portion Use problem 3.52. Add a force of 500 kN that is perpendicularly applied at point B in the direction from B towardC.Remove the torque.The steel and brass are assumed to have Poisson’s ratios of 0.30. (a)Determine the internalforce in AB.(b)Determine the internal force in BC.(c)Determine the deflection at Point B.(d)Determine thereaction at Point A.(e)Determine the reaction at Point C. Explain your work concisely and in detail
A simply supported wood beam with a span of L = 15 ft supports a uniformly distributed load of w = 320 lb/ft. The allowable bending stress of the wood is 1,200 psi. If the aspect ratio of the solid rectangular wood beam is specified as h/b = 2.0, calculate the following: 1. What is the vertical reaction at A in pounds. 2. What is the vertical reaction at C in pounds. 3. Calculate the maximum bending moment in the bean in ft-lb. 4. Calculate the required section modulus S considering the allowable bending stress of the wood in in^3. 5. Calculate the minimum allowable beam width in inches.
The block slides down an incline. It starts from rest and, after moving 6 ft, strikes a spring (k= 100 lb/in). Determine the maximum deformation of the spring. Coeff fr= 0.20. please use energy-work method.
A full forming P= 52 kN axial force acts on the part shaped by the machining method made of xCy steel material. The thickness of the part is t= 20 mm and the steel tensile strength is sigma(tensile) = 620 MPa . Calculate the individual fatigue life of the A and B sections of the machine part for 90% reliability. Draw logarithmic S_N diagrams.
NEED ANSWER ASAP!! A so-called "trapeze bar" in a hospital room provides a means for patients to exercise while in bed (see figure). The bar is 2.1m long and has a cross section in the shape of a regular octagon. The design load is 1.6kN applied at the midpoint of the bar, and the allowable bending stress is 240 MPa. Determine the minimum height h of the bar. Round to one decimal place. (Assume that the ends of the bar are simply supported and that the weight of the bar is negligible.) hmin=___mm
A steel plate 2.5 m x 1.3 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the bearing stress (MPa) in the steel plate the 10 mm diameter pins exert. The correct answer is 14.81. Show solution.