The concrete column (300 mm 300 mm) is reinforced by four steel bars each having diameter of 30 mm as shown in Figure Q1. The working stresses for steel and concrete are 200 MPa and 25 MPa, respectively. Determine the largest axial force P that can be safely applied to the column. Use Est-200 GPa and Eco = 20 GPa. ** 11 11 Dimensions in mm 300 300 Y

The concrete column (300 mm 300 mm) is reinforced by four steel bars each having diameter of 30 mm as shown in Figure Q1. The working stresses for steel and concrete are 200 MPa and 25 MPa, respectively. Determine the largest axial force P that can be safely applied to the column. Use Est-200 GPa and Eco = 20 GPa. ** 11 11 Dimensions in mm 300 300 Y

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows the cross section of a circular steel tube that isf filledwith concrete and topped with a rigid cap. Calculate the stresses in the steel and in the concrete caused by the 200-kip axiall load Use Est = 29 x 10⁶ psi and Eco = 3.5 x 10⁶ psi.
The 400mm x 400 mm square concrete column is reinforced by 6 - 25mm diameter steel bars. If the working stresses for steel and concrete are 345 MPa and 28 MPa, respectively, determine the largest axial force P that can be safely applied to the column. Use Est=200 GPa and Econcrete=25 GPa.
A reinforced concrete beam having a width of 500 mm and an effective depth of 750 mm is reinforced with 5 – 25mm φ. The beam has simple span of 10 m. It carries an ultimate uniform load of 50 KN/m. Use f’c = 28 MPa, and fy = 413 MPa. What is compressive force C resisted by concrete in the beam in KN? Express your answer in two decimal places.
The rectangular reinforced concrete column is reinforced with 6 – 20 mm steel bars as shown. If b = 250 mm and d = 400 mm, determine the stresses in the steel and concrete if the axial compressive load to be supported by the column is 400 kN. For steel, Est = 200 GPa; for concrete, Eco = 15 GPa.
A reinforced concrete column 8 in. in diameter is designed to carry an axial compressive load of 62.3kips. Determine the required area of the reinforcing steel if the allowable stresses are 870 psi and17,404 psi for the concrete and steel, respectively. Use Eco = 2.03 x10^6 and Est = 29 x10^6 psi.
A rectangular concrete beam 277 mm wide and 495 mm deep is simply supported over a span of 8.37 m. the beam is reinforced with straight tendons situated 59 mm above the bottom of the beam under a prestressing force of 387 kN. Concrete weighs 23.36 kN/m3 with modulus of elasticity Ec=13,814.76 MPa. Assuming tension concrete does not crack, what is the midspan deflection due to the given loads. (Include the sign if it is negative) Please avoid rounding off values during the course of solution proper as much as possible. Always write your answer in 4 decimal places
A concrete post is reinforced with 4-28mm diameter steel bars. Compute the stress in each material if it carries a 1000kN compressive force. Esteel = 200 GPa and Ec = 15 GPa
A reinforced concrete column 200 mm in diameter is designed to carry an axial compressive load of 300 kN.Determine the required area of the reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for theconcrete and steel, respectively. Use Eco = 14 GPa and Est = 200 GPa
1. A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of 400 KN. Determine the required area of reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. Use Econcrete = 14 GPa and Esteel = 200 GPa.
5) A square footing 2.2 m x 0.31 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 331 kN LL = 251 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the maximum ultimate bending moment in the slab. Write your final answer as whole number with the unit of kN-m.
The steel framework shown below is used to support the reinforced concrete slab (unit weight of concrete =23.6KN/m3) that is used for an office use (minimum live load = 2.4KPa). The slab is 150 mm thick. Use a=3m, b=5m. Neglect the self-weight of the beam and girder. Assume all beams and girders have simple supports. NSCP 2015 Load factors: 1.2DL & 1.6LL. Calculate the total ultimate/factored SLAB load in Kilo Pascals? Express your answer in 2 decimal places.
b) Using first principles analyze a rectangular beam for having 230 mm width and 550 mm effective depth is reinforced with steel An on tension side only. Taking parameters with the usual notation as k = 0.36, k2 = 0.42 and Eru = 0.0035 determine for concrete of grade M2s and steel of grade Feso obtain. Xu mar, Mur max, As max for balance section; Mur for Au = 800 mm?: