The continuous beam shown below is loaded with a couple, M= 120KN.m, uniformly distributed load of 6kN/m, and two concentrated loads of 12kN and 8kN. Analyze the beam using slope-deflection method. Draw the shear and moment diagrams. 12KN M=120KN.m OKIV 6 kN/m 2m 2m 3m 1.5m 1.5m

The continuous beam shown below is loaded with a couple, M= 120KN.m, uniformly distributed load of 6kN/m, and two concentrated loads of 12kN and 8kN. Analyze the beam using slope-deflection method. Draw the shear and moment diagrams. 12KN M=120KN.m OKIV 6 kN/m 2m 2m 3m 1.5m 1.5m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Find the Shear Moment Diagram of the following problems using ONLY AREA METHOD. 30 kN 50 kN А 1m 3 m…

Q: 50 kN 162 kN.m 10 KN/m TTTT 15 m 6 m

A: Given :- a beam as shown below

Q: A 6m simply supported beam AB carries 2 concentrated downward loads of P=65KN each placed at third…

A: The beam is symmetrical…

Q: Using the moment-distribution method, determine the end moments at B, C, D, and E of the given…

Q: Draw Shear Force Diagram and Bending Moment Diagram for beam below by using Slope Deflection Method.…

A: calculation of fixed end moment for AC assume the udl value is…

Q: Using Slope Deflection Method, determine all reactions at supports also, determine shear and bending…

Q: Draw Shear Force Diagram and Bending Moment Diagram for beam below by using Slope Deflection Method.…

Q: 2. Draw the Shear and Moment Diagram Using Three Moment Equation. 20 kN/m -5.0000 20 kN B 1.0000…

Q: 1. Determine the End Moments of the Beam Shown. Use the Three Moment Equation. E= 205 GPa, 1AB.CD…

A: Solution Given Data E=205 GPaIAB,CD=150×106 mm4IBC=200×106…

Q: Determine the MAXIMUM SHEAR and MAXIMUM MOMENTS for using SHEAR AND MOMENT DIAGRAMS OR BY ANALYTICAL…

Q: If FB = 560 N and FC = 700 N, determine themagnitude and coordinate direction angles of the…

Q: For the given concurrent forces, determine the value of Force F3 and Angle 0 if the resultant is…

A: Given data in question Point forces Angle Resultant force To find out F3 Angle of inclination

Q: Determine the bending moment 2.25 m to the right of point A for the beam shown below if P = 1705 N,…

Q: CO 32 kN/m 3 m 40kN > <-40 kN fig. A

A: The solution of Fig. A by slope deflection method is given below: Since the frame is symmetrical,…

Q: Draw Shear Force Diagram and Bending Moment Diagram for beam below by using Slope Deflection Method.…

A: Here dividing this beam into two parts AC and and CB Thus, Beam AC carries a udl wheread Beam CB…

Q: 1.7 kN/m 3m Mui 1m 20KN

Q: 440 kNm 330 kNm im 3m 2m

Q: Determine the MAXIMUM SHEAR and MAXIMUM MOMENTS for using SHEAR AND MOMENT DIAGRAMS OR BY ANALYTICAL…

Q: A given frame is subjected to loads as shown and analysed using Modified Slope Deflection Method.…

A: Given A frame Required (a)what is the moment KNm at D? (b)what is the maximum positive moment KNm…

Q: From the beam shown with fixed end support atA and rollers at B and C respectively, it carries a…

Q: Problem 4. Construct moment diagrams for the beam using superposition method. 500 N 450 N/m 1.0m…

Q: A cantilever beam of length 3 m and cross section 150 mm wide x 300 mm deep is loaded with a point…

A: Given Data: Length of the beam is L=3 m. Width of the beam is b=150 mm. Depth of the beam is D=300…

Q: A 6m simply supported beam AB carries 2 concentrated downward loads of P=66KN each placed at third…

Q: Swing moment diagram and b) follow the x-limits given to construct the V & M Equations. Also,…

A: According to Our Guideline We are Supposed to do only one set of above question

Q: W = 14 kN/m P = 49 KN Solve for the Beam reactions and draw the shear and moment diagram of the…

Q: Compute the reactions at supports with the computed end-value moments using the slope-deflection…

A: Given Data:End moments MBC=-25kN-mMCB=3.9063 kNmMDC=0

Q: 1. Write shear and moment equations for the beam loaded as shown and sketch the shear and moment…

Q: Using the slope-deflection method, draw the bending moment diagram. 3m 3A 4m 20km 2EJ 3€] D

Q: For questions 2A and 2B, refer to the load and shear diagrams below. 2A. What is the slope of the…

A: Slope of shear diagram from B to C is equal to the loading in region B to C. So, answer= 16 KN/m

Q: From the given beam loaded has shown; Determine the slope at A in radian. Using Moment Area Method.…

Q: For the beam shown, a concentrated load of 20 kips is applied in span, ab, and a uniformly…

A: Note : it is very conceptual question i use in detail method: slope deflection method

Q: 3. A rectangular beam will be designed, so that it will carry the shear force, Vu = 134 kN. Taking…

Q: 1. Write shear and moment equations for the beam loaded as shown and sketch the shear and moment…

A: Given, A beam,

Q: Situation 3. (For Practice) A 5 m simply supported beam is loaded with a 200 kN-m concentrated…

Q: Using 3 Methods, Moment Area Method, Conjugate Beam and Superposition Principle. EI = 100,000 kN-m²…

A: Given data:- Above diagram is given EI = 100000 kN-m2

Q: Using 3 Methods, Moment Area Method, Conjugate Beam and Superposition Principle. EI =100,000 kN-m?…

Q: Problem 1: As in the figure below, compute F using the trapezoidal rule. Let the equation of Force…

Q: 1. Determine the End Moments of the Beam Shown. Use the Three Moment Equation. E= 205 GPa, IA.CD…

Q: W= 1317 kN/m Using Slope Deflection Method, determine all reactions at supports also, determine…

Q: Using Slope Deflection Method for and all reactions at support. Use l = 1/12 b(h³) and E = 2.10x107…

A: Slope deflection method is a structural analysis method and it is use for beans and frames. It is…

Q: For the beam loaded shown below, evaluate the following: Moment Diagram of the Beam Using Conjugate…

A: Given data:

Q: 21 kN/m 24.5 kN/m A E B- |C D – 2 m – – 2 m – - 3 m - -2 m –

Q: curves for the absolute value of the shear and bending moment in the beam by the semi-graphical…

Q: Determine the MAXIMUM SHEAR and MAXIMUM MOMENTS for using SHEAR AND MOMENT DIAGRAMS OR BY ANALYTICAL…

Q: Analyse the beam above using the slope deflection method and also draw the shear force and bending…

Q: Calculate the reactions of supports for each beam below using slope-deflection method of analysis…

Q: 35KN/m 180 kN 15 kN/m B D -5 m- -5 m- -4 m- El = constant E = 70 GPa (10)

A: The moment-area method is generally an important method for determining the bending displacement in…

Q: For questions 2A and 2B, refer to the load and shear diagrams below. 2A. What is the slope of the…

Q: A continuous beam as shown in the figure with a constant value of El. Using slope deflection method.…

A: a.Compute the value of slope at B and C. b. Compute the value of the moment M_AB c. Compute the…

Q: Using Moment Distribution Method, Analyze the statically Indeterminate Beam shown and Draw the shear…

A: Draw SFD and BMD

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

The continuous beam shown below is loaded with a couple, M= 120kN.m,
uniformly distributed load of 6kN/m, and two concentrated loads of 12kN and 8kN. Analyze the beam using slope-deflection method. Draw the shear and moment diagrams

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

FIXED END MOMENTS & SLOPE DEFLECTION EQUATIONS

VIEW

EQUILLIBRIUM EQUATIONS

VIEW

DETERMINATION OF SLOPES

VIEW

DETERMINATION OF MOMENTS AND REACTIONS

VIEW

SFD & BMD

VIEW

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

W= 465kN/mUsing Slope Deflection Method, determine all reactions at supports also, determine shear andbending moments with complete labels. Use |=1/12 bh^3 and E = 2.15x10^7 KPa
From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m and EI = 200MNm^2Determine the following;C. Slope at L/3. D. Deflection at L/3.
W= 1317 kN/mUsing Slope Deflection Method, determine all reactions at supports also, determine shear andbending moments with complete labels. Use |=1/12 bh^3 and E = 2.15x10^7 KPa
Given (Refer to the pictures): Shear and moment diagram of B2 Requirement: What is the deflection of B2 based on the given references? (KINDLY USE AREA-MOMENT METHOD)
A 6m simply supported beam AB carries 2 concentrated downward loads of P=66KN each placed at third points of the beam span. With constant EI=21000 KN-m2. Using Double Integration Method (DIM) with origin taken at point A (left support) where 0 ≤ x ≤ 6m, calculate the slope at the left support A? Express your answer in "degrees" in 3 decimal places. Take note that 180 degrees = pi radians.
A simply-supported beam, 9 m in length, pin at A and roller at B, is subjected to a uniform load of 20 kN/m applied at the beam's middle third. Determine the slope of B wrt A, slope of A wrt B, tangential deviation of A wrt B, and the tangential deviation of B wrt to A. 3
USE THE SLOPE DEFLECTION METHOD TO ANALYSE THE BEAM BELOW AND ALSO DRAW SFD AND BMD AND NET BENDING MOMENT DIAGRAM
Compute the slope at point A and deflection at point C of the beam using moment-area method. If L = 6ft, w= 1.5k/ft, I=76.8 in4, and E= 29,000 ksi.
NEED ASAP, thank you! Using SLOPE DEFLECTION METHOD for the continuous beam below, determine the following structural parameters and support moments using unreduced rotational stiffness; 1. The value that most nearly gives the absolute value of Fixed-end moment (FEM) at joint B of member AB in kN-m, FEMBA 2. The value that most nearly gives the absolute value of Fixed-end moment (FEM) at joint B of member BC in kN-m, FEMBC 3. The value that most nearly gives the absolute value of the Moment at A in kN-m 4. The value that most nearly gives the absolute value of the Moment at B of member AB in kN-m, MBA
Q2) A line AB of slope 3% was measured with steel tape of 30m to be 175.66 m. The weighing of tape was 0.032 m / kg with cross - sectional area of 0.049 cm2 and has length of 30.02m at standard conditions of 20 ° C and a tension of 6 kg. For each time used, it was supported at three points (ends and middle) with tension of 9kg and temperature of 30 ° C. Compute the corrected horizontal distance when the modulus of? elasticity is 2.15 * 106 kg / cm2 and (a = 1.15 * 10-5 / ° C)
Determine the slope at points B and C of the beam shown. Take E=29(10^3)ksi andI=600in^4.
A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.