Answer Set (B). ASAP please The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C.Assume I = 800 x 106 mm and E = 70,000 MPa.FW1ABOCD8 m8 m4 m4 mw1 (kN/m) F (kN)S (mm)SetA (1,2,3,4,5)B (6,7,8,9,0)206025255015If there is a settlement of S at the support C, solve the following using slope deflection method:3. Reaction at A, RA in kN.

Answered: Image /qna-images/answer/4acd4441-0aaa-4dde-9f8f-3f3a0f643d37.jpg

The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C. Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 B C D 8 m 8 m 4 m 4 m w1 (kN/m) F (kN) S (mm) Set A (1,2,3,4,5) B (6,7,8,9,0) 20 60 25 25 50 15 If there is a settlement of S at the support C, solve the following using slope deflection method: 3. Reaction at A, RA in kN.

The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C. Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 B C D 8 m 8 m 4 m 4 m w1 (kN/m) F (kN) S (mm) Set A (1,2,3,4,5) B (6,7,8,9,0) 20 60 25 25 50 15 If there is a settlement of S at the support C, solve the following using slope deflection method: 3. Reaction at A, RA in kN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Gate AB in the figure is 16 ft long and 8 ft wide. Neglecting the weight of the gate, Find the Force acting on the gate shown, if P is –15 kPa (suction), and its location from the hinge, the tank is 3 meters wide.a. P=304.74 kN, 3.30 m c. P=979.74 kN, 2.75 mb. P=529.74 kN, 2.96 m d. P=678.95 kN, 2.87 m
Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the 1m x 5m gate shown in the figure. Pressure of air = 32 kPa Fluids: fluid a (s=3.93) fluid b (s=0.23) fluid c (s=1.19) h1= 0.7 m h2= 1.6 m h3= 3.7 m Round your answer to 3 decimal places.
Water flows at 1.52 m/sec from a reservoir into a 900 mm diameter steel pipe that is 2286 m long and has a thickness of 25 mm. find the water hammer pressure developed by closure of a valve at the end of the line if the closure time is 8 sec. the velocity (celerity) of a pressure wave C=1440m/s, modulus of elasticity of water = 200 MPa and that of steel is 200,000 Mpa. Answer: 868.2 kPa
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
Determine the load that can be lifted by the hydraulic system shown. Use g = 9.81 m⁄s2 .
3) Water is pumped from a reservoir to a packed tower at a volumetric flow rate of0.02 m³/s. Water enters the packed tower from the bottom and exits from the topas given in the figure and the top of the tower is open to the atmosphere. Thepipeline consists of 50 m of 3-inch schedule 40 commercial steel pipe, which includes90° elbows and two fully open gate valves. The diameter and the height of the packingin the tower are 0.8 m and 3 m, respectively. The packing material consists ofspherical ceramics material with a diameter of 2.0 cm and a specific gravity of 2.5.The void fraction of the packed bed is 0.4.a) Determine the pressure drop in the packed bed.b) Calculate the total friction loss between point "1" to point "2".Pwater = 998 kg/m³Hwater = 1x10³ kg/m.s0.8 m3 mH₂O Skip question.
The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend isinstalled in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the xand y for components of the thrust block to hold the pipe bend.
In Fig.2, A Pelton wheel has a mean bucket speed (U) of 89 m/s with a jet of water flowing at the rate of 1 m3/s under a head of 270 m. The buckets deflect the jet through an angle of 170º. Calculate the power delivered to the runner and hydraulic efficiency of the turbine. Take Cv = 0.98 , V= Cv root of 2gH , workdone per second by the jet on the runner = ρaV1 (Vw1 + Vw2) x U and Hydraulic efficiency ηh = 2 U (Vw1 + Vw2)/V12
37. Situation 13 - An open rail car is 6 ft. wide, 9 ft. high, 18 ft. long. It is filled with water to a depth of 7.5 ft. It is accelerated to the right at 10 ft/s2. a. How much water, in ft^3, spills out of the car? Round off to two decimal place. b. Determine the change in pressure, in psf, that acts at point B. Round off to one decimal place. Input the numerical value only. c. Determine the change in pressure, in psf, that acts at point C. Round off to three decimal place. Input the numerical value only.
Fluid Mechanics. Reg.no :5395 Pb # 4: A centrifugal pump is installed to deliver water from a reservoir of surface elevation zero to another reservoir of elevation 350+(Reg.No/100) ft (as shown in Fig. 3). The 15-in-diameter suction pipe (f = 0.024) is 100+(Reg.No/100) ft long and the 13-indiameter discharge pipe (f = 0.028) is Reg.No ft long. The pump characteristic at 1250 rpm is defined by hp = 385 – 25Q2 where hp is the pump head, is in ft and Q is in cfs. Compute the rate at which this pump will deliver water under these conditions.
Fluid mechanics, i need solutions in 10 minutes please. MCQ/The submerged sector gate AB shown in the figure is 1/9 of a circle radius 4 m. The length of the gate is 10 m. Determine the horizontal component of water pressure acting on the gate. A-262.874 kN B-162.328 KN C-324.260 KN D- 448.161 KN E- 591.263 KN F-392.273 kN G- 89.207 kN H-536.078 KN I-208.119 KN J- 490.984 kN K- 127.908 KN L- 113.001 KN
The pump in the figure B. draws water from a reservoir and discharges through 2 V2 inches hose, which terminates in a nozzle having a jet diameter of inch. The head losses are: I to 2. 5.75 ft: 2 to 3. negligible: 3 to 4. 30.61 ft. 4 to 5. 11.6 ft. Compute the required horsepower output of the pump and make a table of the heads at the five points. Q is (a) 261 gpm. (b) 361 gpm.