The crankshaft of a machine runs, on average, at 2280 revolutions per minute for the duration of 2 hours everyday. How many years will it take the crankshaft to fail if its fatigue lifetime in the running condition is 2x100 ?

The crankshaft of a machine runs, on average, at 2280 revolutions per minute for the duration of 2 hours everyday. How many years will it take the crankshaft to fail if its fatigue lifetime in the running condition is 2x100 ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

....A steam engine develops power at mean torque of 19,000 N-m and velocity of 10 m/s. The mean diameter of the flywheel rim is 1.2 meters. The coefficient of fluctuation of speed is 0.03 and the coefficient of fluctuation of energy is 0.21. Determine the thickness of the rim in mm if the width of the rim is twice of its thickness. Assume density of rim material as 7250 kg/m3.
An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number. An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number.
What is the difference between a solid and a hollow shaft in mechanical engineering?
Please show the complete solutions. Rate will be given. No long explanation needed. Answer in 3 decimal places. Mechanics of Deformable Bodies A steel circular shaft (G= 80 GPa) of constant diameter of 28 mm is subjected to the following torques in N-m: TA= 160; TB = 130; TC = 350; TD = 380. The directions of the applied torques are indicated in the figure The bearings shown allow the shaft to turn freely. The length of each segment is equal to 86 cm. (a) Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft. Show the FBD of each segment using a double-headed arrow to represent each torque. Use the same rule of signs as in the lecture. Determine (b) the maximum stress in the shaft in MPa (C) rotation angle of pulley B with respect to pulley D. Solid shaft: J= (f/32 X D4) Hollow: J= (ft/32xD4-d4) Note: Please Follow rule of signs and show complete FBD of each section
Please answer the following question A cigarettes dispenser requires a south African five-rand (R5) coin with a mass of 9.5 g to dispense one cigarette with a mass of 0.2 g. The design of such a cigarette dispenser is based on a helical spring, of negligible mass, which is found to extend 0.1 mm under a mass of 0.2 g. The spring can support a total mass of a coin. As the customer place money on the dispenser, the spring and coin system displace vertically through 4 mm and release. 1.1. Provide a schematic representation of the mass and spring system. 1.2. Calculate the frequency of natural vibration of the dispenser. 1.3. Determine the velocity of the coin when it is 2 mm below its resting position.
01: A 105cm Rod is suspended on a wall with a 5N force pulling upwards, 110 degrees away from the horizontal axis and 5cm from a 50kgm hanging object. Find the location of the C.G. away from the wall. Neglect the Mass of the rod and consider it a rigid body. Assume SSLC. 02: Considering a CCW movement is Positive, what is the total value of the Negative Moments at the point with the 50kgm object? Please answer in four decimal places, in Nm. 03: What is the value of C.G. away from the wall? (in meters, two decimal places)
Determine the width and thickness of the leaves (in mm) of a leaf spring using the following specifications: Total load = 140 kN; Number of springs supporting the load = 4; Maximum number of leaves = 10; Span of the spring = 1000 mm; Permissible deflection = 80 mm; Modulus of elasticity, E = 200 kN/mm2; and allowable stress in spring material is 600 MPa.
A nut which is connected to a lead screw is moved in a horizontal plane against a force of 100kN at a speed of 4mm/sec by electric motor powered screw. The following data is given Single start square thread screw Pitch of the screw = 6mm Outlet diameter of the screw = 40mm Co-efficient of friction of the screw thread = 0.15 Efficiency of the motor = 85% Determine the power required and efficiency of the screw
A pulley has a tangential velocity of 75 fpm. If pulley diameter is 10 inches, find the speed of the speed. A. 24.34 rpm B. 28.65 rpm C. 34.22 rpm D. 32.34 rpm Please solve the Problem elaborately. Your solution will be use as reference for my studies. Thank you so much your work will be appreciated much!
What must be the speed of a load bullet in m/s if it melts when striking a steel slab? The initial temperature of the bullet is T1=300K, its melting point is T2=700K, its heat of melting is q=5cal per gram, and its specific heat is C=0.03 cal per gram per K.A. 378B. 377C. 379D. 376
A 150 mm shaft running in a journal bearing supports a load of 10 kN and has a speed of 1200 rpm. If the coefficient of friction of the journal bearings is 0.015, which of the following is the heat generated due to friction?Group of answer choices 2.70 kW 7.06 kW 1.41 kW 2.45 kW
Which of the following would Newton's first law alone NOT account for? 1) Passengers on board an elevator undergoing uniform motion can't tell that the elevator is really moving. 2) A passenger leans forward in her seat when the car's brakes are applied. 3) During launch, astronauts feel that they are being pushed back into their seats. 4) No matter how hard you push against it, the boulder would not move. 5) A rocket accelerates upward from a launch pad and the engines' thrust overcomes gravity.