The cross section of a concrete dam is shown in the figure. Take the weight-density (= pg) of water to be 10 kN/m³ and that of concrete to be 25 kN/m³. For the given design of the cross-section, find the ratio h/H that is safe enough for the dam to not tip over (about the downstream edge E). Here you will enter the numerical answer. In the handworked file you must show your worked solution. H E 60° H/10 4H/10 h

The cross section of a concrete dam is shown in the figure. Take the weight-density (= pg) of water to be 10 kN/m³ and that of concrete to be 25 kN/m³. For the given design of the cross-section, find the ratio h/H that is safe enough for the dam to not tip over (about the downstream edge E). Here you will enter the numerical answer. In the handworked file you must show your worked solution. H E 60° H/10 4H/10 h

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.16P: Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020...

See similar textbooks

Similar questions

The cross-section of an open tank is shown below at left. BC is a cylindrical surface with radius r = 6 ft, and the tank water depth is h = 10 ft. A free body diagram (FBD) for hydrostatic analysis is shown below at right. Use this information to solve problems 12 through 15 on a per unit width (into the page) basis. FBD: A B B OThe magnitude of the horizontal force Fy is nearest 1a) 490 lb/ft width of tank (b) 1610 Ib/ft width of tank (c) 3120 Ib/ft width of tank (d) 12.5 Ib/ft width of tank (e) None of the above are close to being correct ) The center of pressure Yp is ft below the water surfa The magnitude of the vertical hydrostatic force Fy is nearest (a) 1765 Ib/ft width of tank (b) 3744 Ib/ft width of tank (c) 1980 Ib/ft width of tank (d) 10.4 Ib/ft width of tank (e) 675 Ib/ft width of tank The location of Fy left of side AB is nearest ft OST or DISTREBUTE - THANK YOU
In your response, please display the full computation and all FBDs that were used. Only round off at the final answer with 4 decimal places. P=2kN, F=3kN, and moment M=0.5kN-m are acting on the structure in the illustration. A pin at Z and a cable RQ connected by a connecting pin R support it. Im ● F ● P S TO M Im R lu W OZ a' 0.8m 3m If the pin support Z's factor of safety against shear stress is 3, determine whether a single or double shear should be provided for an economical and safe design. 4 m The mas allowable shear stress in the pin is 50MPa. Consider the following specifications. Single shear design: 25mm pin diameter Double shear design: 17mm pin diameter
The second moment of area of a rectangle is given by the formula I =bh^3/12where b is the breadth and h is the height.Determine the approximate percentage error, if b is measured 3% too largeand the height h is measured 1.7% too small.(Use the Binomial Expansion Method)
Various distributed forces are exerted on the beam shown, w(x) = 2.234 F N/m, p(x) = 1.551 N/m, q(x) = 2.071 N/m, a = 3 m, b = 5 m, and c = 5 m. Determine the net force on them and their direction (+ up. - down). State your answer in kN to 3 significant figures after correct rounding. w (x) a p(x) b q (x)
A cylindrical gate with surface XY is supported by a hinge at point 1. The length of the gate perpendicular to the figure is m. Solve for the magnitude of the horizontal component in kN. Unit wt of water = 9.81 kN/cu.m. LENGTH = 9 RADIUS = 6 ANGLE = 55 RADIUS X ANGLE 1 1,201.34 925.39 1.358.45 1.066.38
Help Save & Exit Check Required information A rope connecting points A and B supports the force Fshown in the figure. Write expressions using Cartesian vector representation for the following. Take L= 8 ft and F= 12 lb. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. B 30° F T AB : the position vector from A to B. TAB of 17 Next > < Prev 6. 9. 41
Find box for the given Plane, where by =120m, d=25m, bz=25m, d2=100m, b3=80m & d3=25 m (Enter only the values in the boxes by referring the unit given in brackets. Also upload your hand written answers in the link provided) b2 dz di bị The value of X= (unit in m) The value of Y= (unit in m) The moment of inertia for sec 1 = lyyi = (unit in m) The moment of inertia for sec 2 = lyy2 = (unit in m4) The moment of inertia for sec 3 = lyya = (unit in m4) The moment of inertia of the given plate = lyy = (unit in m)
Required information A rope connecting points A and B supports the force F shown in the figure. Write expressions using Cartesian vector representation for the following. Take L = 8 ft and F= 12 lb. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. y 30° es ÜAB : the unit vector in the direction from A to B. ûAB =
Given this solution, how does the 0.001404 was calculated? (The value of V)
Solve the first page (2) using the second picture
4. Given: Curb shown below Find: (1) Surface area and (2) volume 100 mm 150 mm 4 m 30° 150 mm 150 mm
The figure below shows a steel structure made up of two pre-assembled segments that are hoisted by a mobile crane using a bespoke lifting frame. Each cable must withstand loads of FAB = FAC = FAD = FAE = 4000 kN. You must provide an accurate answer in scientific standard form with one decimal place only. In cartesian vector and in scalar form, compute the rAB, rAC, TAD & rAE length. 14 m 6m 6 m в 3 m 3 m X