The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close approximation to the handbook value of Ix= 654 in.^4 by treating the section as being composed of three rectangles. The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close approximation to the handbook value of I= 654 in.“ by treating the section as being composed of three rectangles.16.25"- x0.380" E7.073" - 0,628"Answer:T =iin.4

Given: The approximated value of moment of inertia about x-axis, Ix = 654 in^4

The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close approximation to the handbook value of I = 654 in.“ by treating the section as being composed of three rectangles. 16.25" 0.380" – 7.073 - 0.628" Answer: T -i in.4

The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close approximation to the handbook value of I = 654 in.“ by treating the section as being composed of three rectangles. 16.25" 0.380" – 7.073 - 0.628" Answer: T -i in.4

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.16P: Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020...

See similar textbooks

Similar questions

The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm tw = 16 mm d = 110 mm t = 4.8 mm Additionally: • The area of each pipe is A = 1586 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 194710000 mm4. If the beam will be subjected to a shear force of V = 170 kN, determine the shear stress at point K, located at yK = 70 mm below the z centroidal axis.
Determine the shape factor f for a hollow circular cross section has an inner radius r1 and a radius outer r2.
The beam is made of four aluminium plates welded together as shown in Figure 1. Knowing that E = 65 GPa and neglecting the effect of the fillet. Determine the corresponding radius of curvature of the beam.
Determine the equivalent stiffness of a cantilever beam which is loaded transversely on its end and has a length in 5000 mm and an annular cross section with inner and outer diameters of 25 mm and 22 mm, respectively. The modulus of elasticity of the beam is 72x109 N/m2. Use moment of inertia I=π(D4o−D4i)/64 and spring constant is (k= 500 N/m). Answer must be in three decimal places.
Q: Shear of Thin-Walled Beams (open section 1. The figure below shows the cross section of a thin, singly symmetrical I-section. Show that the distance & of the shear center from the vertical web is given by d (1+12p) where p=d /h., The thickness is taken negligibly small in comparison with the other dimensions and fj < I,
A beam is subjected to equal bending moments of Mz = 57 kip·ft. The cross-sectional dimensions are b1 = 8.3 in., d1 = 1.4 in., b2 = 0.90 in., d2 = 6.2 in., b3 = 2.4 in., and d3 = 1.7 in. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
A beam is subjected to equal bending moments of Mz = 44 kip·ft. The cross-sectional dimensions are b1 = 6.5 in., d1 = 1.5 in., b2 = 0.90 in., d2 = 6.2 in., b3 = 2.6 in., and d3 = 1.8 in. Determine:(a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis.(b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative.(c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative.(d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
a) A simply supported beam has a symmetrical rectangular cross-section. If the second moment of area (I) of a beam with a rectangular cross-section is11.50 x 106 mm4 about its centroidal x-axis and the depth dimension (d) of the rectangular section is 180 mm, determine the breadth dimension (b) for this beam section. Give your answer in millimetres (mm) and to 2 decimal places. Assume the beam section material is homogeneous. b) The same rectangular cross-section beam in Q2b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (σmax) the beam will experience. Give your answer in N/mm2 and to 2 decimal places.
a) A simply supported beam has a symmetrical rectangular cross-section. If the second moment of area (I) of a beam with a rectangular cross-section is11.50 x 106 mm4 about its centroidal x-axis and the depth dimension (d) of the rectangular section is 180 mm, determine the breadth dimension (b) for this beam section. Give your answer in millimetres (mm) and to 2 decimal places. Assume the beam section material is homogeneous. b) The same rectangular cross-section beam in Q2b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (?max) the beam will experience. Give your answer in N/mm2 and to 2 decimal places.
A beam is carrying a moment M as indicated. The cross section of the beam is symmetric about the z axis. The dimensions of the cross section and the location of the centroid (point C) are shown. Knowing that Iy = 280,000 mm4, Iz = 150,000 mm4, and M = 400,000 + UV in N.mm, where UV is 21(a) Calculate the components of the bending moment on the y and z axes, Myand Mz.(b) Identify which point at the cross section has the largest tensile stress, and which point at the cross section has the largest compressive stress.(c) Calculate the maximum tensile stress and the maximum compressive stress in the cross section
The section modulus for the beam of rectangular cross section of size 50 mm x 40 mm is ______________ mm3.
Determine the displacement at point C on the steel overhanging beam shown in Fig. a. Take Est = 29(103) ksi, I = 125 in4.