The currents flowing in the lines toward a balanced load connected in A are Ia 10020° A, I, = 141.4225° A, and I. = 100290° A. Look for the following: a.Find the symmetrical components of the given line currents b.Draw the phasor diagram of the positive sequence currents of the line currents c. Draw the phasor diagram of the negative sequence currents of the line currents d.What is Iab?'

The currents flowing in the lines toward a balanced load connected in A are Ia 10020° A, I, = 141.4225° A, and I. = 100290° A. Look for the following: a.Find the symmetrical components of the given line currents b.Draw the phasor diagram of the positive sequence currents of the line currents c. Draw the phasor diagram of the negative sequence currents of the line currents d.What is Iab?'

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.13P

See similar textbooks

Similar questions

A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
The line with symmetrical spacing then the equilateral spacing (Deq) for the three-phase inductance calculation is D12=D23=D31=D. Select one: True False
Having a phase impedance of 23.7 + j17.1 Ω at 50 Hz given in Figure Δ-connected load, Y-joint source resulting in 400 V and 50 Hz with impedance 0.1 + j0.3 Ω on each line fed by. According to this, a) Find the line flow and load voltage. b) Find the load-arm currents. c) There are active and protective forces produced by the source.
Explain thoroughly relevant information/concepts regarding the DELTA-WYE TRANSFORMATION
If a load is symmetric with 50 ohm of series impedance and 13 ohms of mutual impedance, what are the sequence impedances? a. z11 = z22 = 63 ohm, z33 = 89 ohm, else 0 b. z11 = z22 = 33 ohm, Z00 = 76 ohm, else 0 c. z11 = z22 = 50 ohm, Z00 =89 ohm, else 0
a short three phase transmission line connected to 33kv 50 hertz generating station at starting and is required to supply a load of 10 MW at pointed start lagging power factor at 30 KV addresses in that is the minimum transmission efficiency is to be determined96% estimate the per face value of resistance and inductance of a line
The load impedance ZL for the circuit shown is adjusted until maximum average power is delivered to ZL.1. a) Find the maximum average power delivered to ZL.2. b) What percentage of the total power developed in the circuit isdelivered to ZL?
Estimate the distance over which a load of 15000 KW at p.f-0.8 lagging can be delivered by a 3-phase T.L having conductor each of resistance 0.8 2 per km the voltage at the receiving end is to be 132 KV and the losses in the line is to be 5% of received power
The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
For a balanced- load supplied by a balanced positive-sequence source. the line currents into the load are 3 times the -Ioad currents and lag by 30. (a) True (b) False
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance