The diamter of precast round piles under pile cap is 400mm, the embedded depth of cap bottom is 1.5m, the thickness of the soft clay 1₁=8m and enter the hard plastic clay /₂=2m. Try to calculate the bearing capacity characteristic value of a single pile according to building foundation design code. 9sia 5kPa soft clay Asia 35kPa hard apa 1025kPa clay ра 8m 2m 1.5m

The diamter of precast round piles under pile cap is 400mm, the embedded depth of cap bottom is 1.5m, the thickness of the soft clay 1₁=8m and enter the hard plastic clay /₂=2m. Try to calculate the bearing capacity characteristic value of a single pile according to building foundation design code. 9sia 5kPa soft clay Asia 35kPa hard apa 1025kPa clay ра 8m 2m 1.5m

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter9: Pile Foundations

Section: Chapter Questions

Problem 9.30P

See similar textbooks

Similar questions

Question 18 Nine-pile group consist of 0.36-meter-diameter friction concrete piles 20 m long arranged in 3 rows by 3 columns. The piles are driven into clay having unconfined compressive strength of 147 kPa. The spacing of piles is 0.68 m. on-center. Adhesion factor of the piles is α = 0.53. Determine the allowable block capacity (in kN) of the piile group based on the arrangement described. Use FS = 2.75. Round off to two decimal places.
A group of 9 piles, 12 m long and 400 mm in diameter is arranged in a square pattern in homogeneous clay soil. The c/c spacing of the pile are 1000 mm. The properties of clay soil is given below Cc =0.10, e0=0.9, γsat = 20 kN/m^3, unconfined compressive strength qu= 70 kN/m^2 assume adhesion factor 0.7,. Water table is at GL. Determine the FOS against bearing if 1500 kN load is applied on the pile group and total settlement of pile group under the same load
The circular concrete pile (γc=23kN/m3) of Figure Q2 has dimensions which depend on the ultimate (j) and the penultimate (i) digit of your ID number as described by the formulae in Table Q2. It is constructed inside a sand with shear strength characteristics as given inTable Q2 as well. Calculate the safety factor for a working load equal to Q=300kN. Note : My ID Number is 9477287
What is the pile bearing capacity if the Downward drag = 0.6 psi, h1 = 30', h2 = 4', Frictional stress = 3.5psiAxial stress = 250psi.
Help me solve please A pile with a square cross-section, B × B = 0.5 m × 0.5 m, is driven in a clay soil which has anundrained strength of 40 kPa at the ground surface, increasing thereafter by 3 kPa per meterdepth. a) Determine the required length of an individual pile which is supposed to take a load of500 kN on its top. Assume the factor of safety of 1.5 for both side shear and base resistance.The side shear on the pile may be taken as 55% of the soil’s undrained strength (show all steps)
2. A 40 cm diameter pile carries an allowable load of 200 kN with unit weight of 19 kN/m3 and cohesion of 48 kPa. determine the following:(a) Lengthofthepile.(b) Unconfined compressive strength.
A 30 cm diameter concrete pile is driven in a normally consolidated clay deposit 15 m thick. Estimate the safe load. Take cu = 70 kN/m^2 , α= 0.9 and FS= 2.5 . [Ans, 375 kN]
A square pile (B=0.3m) is installed in a silty sand with a friction angle of approximately 28 andno cohesion. The soil is saturated, with a unit weight of 19 kN/m3. Pile length is 15m. Determinethe ultimate load capacity of the pile for the current soil conditions. Use all methods availableand get the best estimate. Estimate the elastic settlement of the pile, assuming a FS = 3. Use Ep= 21 x 106 kN/m2; Es = 20 x 103 kN/m2; µs = 0.35 and ξ = 0.67.
A group of 30 HP 10 x 57 piles are arranged in a 5 x 6 grid at 27 in on center. The soil isa clay with unit side friction resistance fS = 2000 lb/ft2 and a unit toe bearing resistanceqn’ = 15000 lb/ft2. See table 21.1 for the steel H-pile cross-sectional data of the standardH profiles in the Coduto book or elsewhere. Assume that H-piles are plugged. a)Determine the pile length which separates individual and block failure of pile group. b)Determine the nominal capacity of the pile group Png at this critical length.
5 A group of 9 piles of 28 cm diameter is arranged in a square configuration with a center-to-center spacing of 1.11 m. The length of the piles is 13 m. Unit cohesion of the clay is 94 kPa. Determine the ultimate group capacity of the pile group based on block failure. Assume adhesion factor of 0.72. Round off to two decimal places.
A rectangular pile (0.85 x 0.77) is driven in clayey soil arrangement composed of two different layers. First laye has a height of 9 m., cohesion of 59 kPA, friction factor of 0.84. Second Layer has a height of 5m., cohesion of 74 kPa, and friction factor of 0.87. Compute the allowable load that the pile can carry if the factor safety is 2.37. Use stored value. Answer to 5 decimal places.
A nine pile group consists of 0.30m diameter friction concrete piles 12m long. The piles are driven into clay having an unconfined compressive strength of 180kPa and the unit weight of clay is 18kN/m3. The spacing of piles is 0.75m center to center. Assuming a bearing capacity factor of Nc = 9, a= 1.0. Which of the following most nearly gives the minimum pile spacing in order to achieve 100% efficiency?