Answered: The difference between the heights of…

The difference between the heights of energy grade line (EGL) and hydraulic grade line (HGL) is equal to (a) z (b) P/ρg (c) V2/2g (d ) z + P/ρg (e) z + V2/2g

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.37P

See similar textbooks

Related questions

Q: The appropriate conservation law applicable for solving hydraulic machines problem le 1)…

A: As, we know fluid flows from higher total energy (or energy head) That's why in hydraulic machine…

Q: 3. The velocity of the flow () in a pipe is equal to a. b. C. d. V V = V 2gx20 1+ 200 2gx20 1+200/…

Q: The total discharge in the system below is 15.5 cfs and the head loss from B to C is 24 ft. Using n…

A: Note: As per policy, we can solve the first three subparts. Please resubmit the remaining parts.…

Q: A hydraulic turbine generator was installed at a site 101 m below the free surface of a large water…

A: Given Data: The mass flow rate of water, m=859 kg/s Mechanical power, 800 kW Electrical power, 779…

Q: The bernoulli's equation between 2 sections in a flow channel, for ideal fluid is ___________ Total…

A: Bernoulli's equation is an energy conservation equation. The Bernoulli's equation is shown below.

Q: Flow with small Re tends to be O A. Re has no relation with flow types O B. transitional flow O C.…

Q: When water is pumped into a water tank 20 m above a lake with a flow rate of 70 l/s, 20.4kW of…

A: Given data:- Head(H) = 20 m Discharge(Q) = 70 L/sec Electric power = 20.4 k

Q: In a pumping system handling water, the level in the suction tank is 3.2m below the pump shaft…

Q: A pump is used to raise water to a reservoir through 800 m of 20 cm diameter pipe (f=0.033). If the…

Q: A river flowing steadily at a rate of 167 m3/s is considered for hydroelectric power generation.…

Q: A pump is used to raise water to a reservoir through 800 m of 20 cm diameter pipe (f=0.033). If the…

Q: Rank in order, from highest to lowest, the liquid heights h1 to h4 in tubes 1 to 4. The airflow is…

A: The height of liquid in tube increases with the increase in velocity, since higher the velocity,…

Q: R2 R, R3 A fan delivers air to a system as shown above where R1= 40 mm of water for a volume flow of…

A: given: R1=40mm of waterand Volume(V1)=160m3/minR2=R3=16.5mm of water volume flow(V)=50m3/min volume…

Q: A cylindrical well is 2m in diameter and 12 m deep. If there is 3m of water in the bottom of the…

A: Given that: Diameter of the well = 2 m Depth of the well = 12 m Depth of water inside the well = 3 m…

Q: In a pumping system handling water, the level in the suction tank is 3.2m below the pump shaft…

A: NOTE:- As per our company guidelines we are supposed to answer only one question. Kindly repost…

Q: In a hydraulic system the overall efficiency is the ratio of cylinder output power divided by motor…

Q: A pump is used to raise water to a reservoir through 800 m of 20 cm diameter pipe (f=0.033). If the…

Q: A hydraulic turbine is used to generate power by using water in a dam. The elevation difference…

Q: L = 35 cm D, - 6mmo (0 y= 16cm x= 35cm h= 12cm d = 10cm %3D

A: The theoretical velocity of the water throught the orifice can be calculated using the Bernoulli's…

Q: A hydraulic turbine is used to generate power by using water in a dam. The elevation difference…

Q: A new cast-iron pipe 400 m long and 15 cm in diameter carries 42 L/s of water. Determine the…

Q: Choose correct answer: Pump converts ___________ A. Mechanical energy to Hydraulic energy B.…

A: Pump converts the Mechanical energy into hydraulic energy of the liquid.

Q: An ice skater rotating on frictionless ice brings her hands into her body so that she rotates…

Q: A river flowing steadily at a rate of 175 m^3 /s is considered for hydroelectric power generation.…

A: Given data: Water flow rate, Q=175 m3sElevation, h=80 m Constant values: Density of water, ρ=998…

Q: A hydraulic turbine is used to generate power by using water in a dam. The elevation difference…

A: Option A is correct.

Q: The rate of flow of water through a horizontal pipe is 271 lit/s. The area of the pipe suddenly…

A: We need to calculate head loss, pressure in larger pipe and power lost

Q: A spherical tank of diameter 6 m is full of water. Set-up the integral for the work done in pumpir…

A: To Find : the work done in pumping Given : Diameter of tank D=6m density of water…

Q: The total energy-line is always higher than the hydraulic gradient line, the vertical distance…

A: The concept of hydraulic gradient line and total energy line is very useful in the study of flow…

Q: What do we mean by "Pump Characteristics"? And how they are presented? And how can we select a pump…

A: INTRODUCTION: Positive displacement pumps and dynamic pumps are the two primary groups of pumps.…

Q: A 3-cm-diameter horizontal pipe attached to a surface makes a 90° turn to a vertical upward…

A: Given data D=0.03 mV=9 m/sec

Q: A hydraulic turbine is used to generate power by using water in a dam. The elevation difference…

A: Given data, Elevation different between free surface and down stream is h= 120 m. mass flow rate is…

Q: Q.3) Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of…

A: Givenpower provided by pump to water P=20kWZ=45mhL=23m

Q: Along a galvanized iron pipe (ε=0.15 mm) of 30 cm in diameter, pump 60 lps of oil; µ = 0.016 N s/m2…

A: Surface roughness of galvanized iron pipe, ε=0.15 mm=0.15*10-3 mPipe diameter, d=30 cm=0.3 mOil flow…

Q: The weight of a water tank open to the atmosphere is balanced by a counterweight, as shown. There is…

A: Now as per the given condition The area of the outlet hole is given asAh=π4d2here d=4 cm=0.04…

Q: 22 L kerosene tank is filled with 2 cm diameter hose equipped with a 1.5 cm nozzle meter If it takes…

Q: The water in an 5.2 m-diameter, 6.6 m-high above-ground swimming pool is to be emptied by unplugging…

Q: Q2// Water enters a hydraulic turbine through a 26 cm diameter pipe at a rate of 1.2 m^3/s and exits…

A: Given data: The diameter of the inlet pipe, d1 = 26 cm. The diameter of the exit pipe, d2 = 21 cm.…

Q: How can you evaluate the vertical force acting on a horizontal surface immersed in a liquid?

A: If a horizontal surface is immersed in a liquid then the vertical force acting on it will be the…

Q: A river flowing steadily at a rate of 175 m^3/s is considered for hydroelectric power generation. It…

Q: The drinking water needs of an office are met by large water bottles. One end of a 0.35-in-diameter,…

A: The diameter of the plastic hose is D=0.35 in. The total length of the plastic hose is L=6 ft. The…

Q: Can we use this pump to supply water to an elvation 35 meters above? Explain your answer.

A: Given: Water Pump with manufacturer specifications

Q: The weight of a water tank open to the atmosphere is balanced by a counterweight. There is a 4-cm…

A: Velocity of water at exit through pipe can be determined as Discharge from hole can be determined…

Q: Which quantities are added when two pumps are connected in series and parallel?…

A: When two identical pumps are arranged in series then head is double with same mass flow rate. When…

Q: What is the Stefan-Boltzmann Law? Distinguish between black and gray body What is the hydraulic…

A: There are three types of heat transfer that is possible 1. conduction 2. convection 3. radiation…

Q: A hydro electric plant having 30 sq. km reservoir area and 100 m head is used to generate power. The…

Q: A hydraulic turbine receives water from a reservoir of 50 meter above it. What is the minimum flow…

A: h=50m P=30MW

Q: A siphon used to empty a tank consists essentially of a pipe with its summit 0.5 m above the water…

A: Given, Height of the summit above the water surface in container 1 = 0.5m Height of the summit…

Q: Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m3/s. Now a diffuser with an…

A: Solution: Given data: d = 10 cm D = 20 cm Q = 0.1 m3/s

Q: The brake horsepower and water horsepower of a pump are determined to be 15 kW and 12 kW,…

Q: Extract the following relation called the Wicket gate function. gnh + H, + w?r? w cot ao + 2nB wrz…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

The difference between the heights of energy grade line (EGL) and hydraulic grade line (HGL) is equal to (a) z (b) P/ρg (c) V²/2g (d ) z + P/ρg (e) z + V²/2g

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Dynamics of Rigid Bodies A cylindrical well is 2m in diameter and 12 m deep. If there is 3m of water in the bottom of the well, determine the work done in pumping all this water to the surface. (Answer: 970kN m) Refer to the above problem, what wokr must be done by a pump that is 60 percent efficient? (Answer: 1620 kN m) Need solution pls
A turbine is placed at the bottom of a 20-m-high water body. Water flows through the turbine at a rate of 30 m3 /s. If the shaft power delivered by the turbine is 5 MW, the turbine efficiency is (a) 85% (b) 79% (c) 88% (d) 74% (e) 82%
A 22 L kerosene tank is filled with 2 cm diameter hose equipped with a 1.5 cm nozzle meter If it takes 20 s to fill the tank, determine the pressure differnce indicated by the nozzle if Cd= 0.96. The specific gravity of kerosene is 0.82. (WITH FREE BODY DIAGRAM) CHOICES: a.10.8 kPa b.12.8 kPa c.11.8 kPa d.9.8 kPa
The brake horsepower and water horsepower of a pump are determined to be 15 kW and 12 kW, respectively. If the flow rate of water to the pump under these conditions is 0.05 m3/s, the total head loss of the pump is (a) 11.5 m (b) 9.3 m (c) 7.7 m (d) 6.1 m (e) 4.9 m
Include a free body diagram 4. A hydraulic turbine is used to generate power by using water in a dam. The elevation difference between the free surface stream and the downstream of the dam is 120 m. The water is supplied to the turbine at a rate of 150 kg/s. if the shaft power output from the turbine is 155 KW, the efficiency of the turbine isA.0.77B. 0.88C. 0.80D. 0.85
In an hydroelectric plant, 100 m^3/s of water flows from elevation of 120 m to a turbine, where electric power is generated. The overall efficiency of the turbine-generator is 80 percent Disregarding frictional losses in piping. Estimate the electric power output of this plant.
Include a free body diagram. Water is being pumped from a large lake to a reservoir 25 m above at a rate of 25 L/s by a 10-kW (shaft) pump. If the irreversible head loss of the piping system is 5 m, determine the mechanical efficiency of the pump. prove the answer: 73.6 percent
A 22 L kerosene tank is filled with 2 cm diameter hose equipped with a 1.5 cm nozzle meter If it takes 20 s to fill the tank, determine the pressure differnce indicated by the nozzle if Cd= 0.96. The specific gravity of kerosene is 0.82. a.12.8 kPa b.11.8 kPa c.9.8 kPa d.10.8 kPa
A river flowing steadily at a rate of 167 m3/s is considered for hydroelectric power generation.Determine the minimum elevation difference (meters) required to for the dam, in order togenerate 550 MW
Water is pumped from a large lower reservoir to a higher reservoir. Someone claims that if the head loss is negligible, the required pump head is equal to the elevation difference between the free surfaces of the two reservoirs. Do you agree?
A hydraulic turbine is used to generate power by using water in a dam. The elevation difference between the free surface stream and the downstream of the dam is 120 m. The water is supplied to the turbine at a rate of 150 kg/s. if the shaft power output from the turbine is 155 KW, the efficiency of the turbine is_____. Include the diagram in your solution. A.0.85 B.0.77 C.0.88 D.0.80
Water enters a hydraulic turbine through a 30-cm-diameter pipe at a rate of 0.6 m3/s and exits through a 25-cm-diameter pipe. The pressure drop in the turbine is measured by a mercury manometer to be 1.2 m. For a combined turbine– generator efficiency of 83 percent, determine the net electric power output. Disregard the effect of the kinetic energy correction factors