The diodes in the following circuit are modeled as ideal diodes with a 0.7 volt forward-bias voltage drop. The input voltage Vin is slowly swept through a range of values from -10 volts to +10 volts. Plot the output voltage Vout on the graph below and plot the currents Ip1, Ip2, and IR on the graphs on the following pages. Vin Ip2 D, Vout Ipt 5 V 10 n IR vs Vin Sketch IR 0.9 0.8 0.7 0.6 0.5 0.4 0.3 + 0.2 0.1 -10 -9 -8 -7 -6-5 -4 -3 -2 2. 3. 5n 6. 7. 8. 9 10 Vin -0.2 0.3 -0.4 -0.5 -0.6 -0.7 -08 00 4.

The diodes in the following circuit are modeled as ideal diodes with a 0.7 volt forward-bias voltage drop. The input voltage Vin is slowly swept through a range of values from -10 volts to +10 volts. Plot the output voltage Vout on the graph below and plot the currents Ip1, Ip2, and IR on the graphs on the following pages. Vin Ip2 D, Vout Ipt 5 V 10 n IR vs Vin Sketch IR 0.9 0.8 0.7 0.6 0.5 0.4 0.3 + 0.2 0.1 -10 -9 -8 -7 -6-5 -4 -3 -2 2. 3. 5n 6. 7. 8. 9 10 Vin -0.2 0.3 -0.4 -0.5 -0.6 -0.7 -08 00 4.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
What is the difference between a diode and rectifier?
Zener diodes are special purpose diodes designed to operate in their breakdown regions. Describe the working principle and characteristics of a typical Zener diode found in the market place. The Zener-diode regulator circuit shown below is to be used to provide a stabilised output to the load. The zener diode characteristic is also shown. Find the load voltage and source current if the battery voltage is 20 V, series resistance is 1.4 kohm and load resistance is 6 kohm
Consider the diode circuit shown below. If in the given circuit, Vs is replaced by a 12V battery and diodes D1 & D2 are considered ideal, what is the potential Vout equal to?
a) Use the diode’s characteristic equation,ID=Is exp(VD/VT), to determine the currentsourceIso that the output voltage is 1.5 V. b) If a load is attached to the output that draws 1 mA, what is the output voltage? c) If the circuit heats up to 40◦C, what is the output voltage without a load?
For the diode applied in the circuit has a knee current of 5mA, and a maximum allowed power dissipation of 300mW. What are the maximum and minimum load currents that can be drawn safely from the circuit with constant voltage output Vo of 6V?
Consider the diode circuit shown below. If Vs is a sinewave with a peak amplitude of 12 Volts at 60Hz, and diodes D1 & D2 are considered ideal, sketch the appearance of the waveform at node voltage Vout . Sketch the appearance of the waveform at Vout .
A silicon diode with a forward resistance of 10Ω is connected in series with a 500Ω resistor. If an A.Cvoltage of 20V peak is connected across the series combination of the diode and the resistor what willbe the peak value of the current through the diode and the peak output voltage? What will be the peakvalue of the current through the diode and the peak output voltage if the diode were ideal?
Sketch i against v to scale for the circuit. The diodes are typycal small-signal silicon devices 300 K. The reverse-breakdown voltages of the diodes are shown. Assume .6 V for all diodes (including Zenners) in the forward-bias region.
In each of the ideal-diode circuits shown below V1 is a 1kHz, 10-V peak sine wave. Sketch the waveform resulting at V0. What are its positive and negative peak values?
Briefly discuss the difference between Diode Piecewise-linear model, Simplified model, and Ideal device/ equivalent circuit. Study the diode specification sheets of a 1N4001 and 1N5401 diodes provided by the manufacturer and compare their difference. Give typical application of each. Discuss briefly how to test junction diode.