97.l.l?9:1Ythe system blocks shown below is inequilibrium, the weight of block A is10 kN and for block B is 35 kN. Thecoefficient of friction between A andsurface is 0.2 and between two block:A and B is 0.15. Answer the followingP=40KNالخيار رقم 15 نقاطThe direction of friction forcebetween two blocks which* effect on block A is inFirst Quarter OSecond QuarterThird QuarterFourth Quarterهذا السؤال مطلوب

Answered: Image /qna-images/answer/eb460a62-5f38-4920-b4af-dd43b9ede5aa.jpg

Answered: The direction of friction force between…

Engineering

Mechanical Engineering

The direction of friction force between two blocks which effect on block A is in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Fred pushes a 55 kg refrigerator with a force P = 100 N inclined at 30° from the horizontal at 1.60 m from the floor as shown in the diagram. The coefficient of static friction between the floor and the refrigerator is 0.40.1. Which among the choices shows the limiting value of the frictional force between the refrigerator and the floor?A) 90.9 NB) 195.8 NC) 108.8 ND) 490 N2. Is the refrigerator not moving, moving, or on the verge of moving? Prove this through calculations.3) Write the correct moment equilibrium equation about A for the refrigerator. (Just use P, don't use P =100)
If there is no friction between shaft AB and the collar, what angular velocity Ö must the mechanism have to keep the collar at r= 660 mm from the vertical axis? Consider the same mechanism again, with m = 3.3 kg, d = 275 mm, k = 180 N/m, only now, instead of being smooth, the collar and shaft have a maximumcoefficient of friction of 0.74. What is the minimum angular velocity required to keep the collar at a constant distance r= 660 mm from the axis of rotation?
Consider the system shown below. The incline plane is fixed and the coefficient kinetic friction between M and 2M is ?1, and coefficient kinetic friction between the plane and 2M is ?2. Let M=2.0kg, ?=22o, ?1=0.14, and ?2=0.25. (a) What is the magnitude of the frictional force on mass M? (b) What is the magnitude of the total frictional force on mass 2M? (c) What is the acceleration of mass M? (d) What is the acceleration of mass 2M?
A car weighing W1 starts moving from the point A of the inclined plane that makes an angle α with the horizontal, hitting the block B, which is at a distance of ℓ, and move smoothly. Since the kinematic friction coefficient µk between the block B and the inclined plane is µk, find the “X” distance where the car and block will stop. W1=W2; ℓ=10 m; µk=0.5; α= 12°
2.5 kg block is initially at rest on a horizontal surface. A horizontal force of magnitude 5.8 N and a vertical force are then applied to the block. The coefficients of friction for the block and surface are ?s = 0.38 and ?k = 0.23. (a) Determine the magnitude of the frictional force acting on the block if the magnitude of is 8.0 N. N(b) Determine the magnitude of the frictional force acting on the block if the magnitude of is 10.0 N. N(c) Determine the magnitude of the frictional force acting on the block if the magnitude of is 12.0 N. N
A 1800-kg truck travels at 85kph around a banked curve with a radius of 250 m. What should be the super-elevation so that the tire friction is equal in magnitude to superel-evation? A. 0.114 B. 0.295 C. 0.227 D. 0.382 E. None of the above
Consider the following arrangement of masses: Mass 1 is connected to mass 2 by a very light string and moves over a frictionless pulley so that both masses move with the same speed and move the same distances (?2 to the right a distance ? and ?1 down a distance ?).Assume ?1 = 15 ??, ?2 = 15 ??, and the coefficient of kinetic friction between ?2 and the table is ?? = 0.73. Let the masses start with an initial speed of 1.00 m/s. What is their speed after moving 1.00 cm (? = 0.0100 ?)?
A belt drive is required to transmit 12 kW power. The velocity of the belt is 9.6 m/sec. If coefficient of friction is 0.25 and the angle of contact is 150º, determine the maximum tension is the belt.
1. If there is no friction between shaft AB and the collar, what angular velocity θ˙˙ must the mechanism have to keep the collar at r=300 mm from the vertical axis? Express your answer to three significant figures. 2. Consider the same mechanism again, with m=2.95 kg, d=225 mm, k=250 N/m, only now, instead of being smooth, the collar and shaft have a maximum coefficient of friction of μs=0.297. What is the minimum angular velocity required to keep the collar at a constant distance r=300 mm from the axis of rotation? Express your answer to three significant figures.
A 1855 kg car has a velocity of 100 km/h when the brakes are fully applied. Assume modern traction control eliminates tire skidding. Determine time and distance to stop the car if dry-pavement static friction coefficient is 0.8.Creat a conclusion for this problem.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Block D, initially at rest, having a W = 30 lbf , is supported within the system shown, with x = 13.2 ft. Neglecting the mass of the pulley and the cord on the system, determine the eventual height h after a force P = 60 lbf is applied to make the block rise by ∆sD = 0.625 ft at t = 2.5 s. NOTE: Use Force-Mass-Acceleration (FMA) Method.
Block A of 500-kg mass is subjected to a towing force F= 2000 t^2 + 3000 t N where "t" is in seconds. If the initial velocity of the block is 6 m/s, determine the velocity after 4 seconds. The block is being towed at a surface inclined at 45 degrees and the coefficient of kinetic friction between these is 0.2. Answer: 106.04 m/s Show COMPLETE STEP-BY-STEP SOLUTIONS and NECESSARY FIGURES to satisfy the answer. Thank you