The distance between a flying drone carrying a laser scanner and a building (Figure 4) is300m. The distance can be calculated using equation below, where, ris the distance, c is thespeed of light and At is the time taken from the laser scanner and the object.r = 1 .c. At2Given the building size and shape as in Figure 4. Scanning resolution for this scanner is 4000points in 1 m?. Consider c = 3.00x10® m/s.Calculate the time taken to scan all possible surfaces of the building.20 m40 m1/8 circleRadius = 25mWidth = 40 m50 m25 m10 m15 m20 m

Answered: Image /qna-images/answer/184aa034-d3e4-4dab-9a62-d44ca771e7a4.jpg

The distance between a flying drone carrying a laser scanner and a building (Figure 4) is 300m. The distance can be calculated using equation below, where, ris the distance, c is the speed of light and At is the time taken from the laser scanner and the object. r = 1 .c. At Given the building size and shape as in Figure 4. Scanning resolution for this scanner is 4000 points in 1 m?. Consider c = 3.00×10® m/s. Calculate the time taken to scan all possible surfaces of the building. 20 m 40 m 1/8 circle Radius = 25m Width = 40 m 50 m 25 m 10 m 15 m 20 m

The distance between a flying drone carrying a laser scanner and a building (Figure 4) is 300m. The distance can be calculated using equation below, where, ris the distance, c is the speed of light and At is the time taken from the laser scanner and the object. r = 1 .c. At Given the building size and shape as in Figure 4. Scanning resolution for this scanner is 4000 points in 1 m?. Consider c = 3.00×10® m/s. Calculate the time taken to scan all possible surfaces of the building. 20 m 40 m 1/8 circle Radius = 25m Width = 40 m 50 m 25 m 10 m 15 m 20 m

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.2DP

See similar textbooks

Similar questions

In order to establish the sphere's 6D Cartesian Pose, how many RGB cameras do you need? Energize both of your responses
A 2.5 m long vane is rotated slowly in a circle. An optical encoder isattached to the vane at its center. It is necessary to know the tipposition of the vane within +/-1 cm. What should be the resolutionof the optical encoder attached to the shaft that positions the vane?
What is one-dimensional kinematics and how does it work?
The sun is the only star whose size we can easily measure directly; astronomers therefore estimate the sizes of other stars using Stefan's law. The spectrum of the star Betelgeuse, plotted as a function of energy, peaks at a photon energy of 0.8 eV, while Betelgeuse is approximately 10,000 times as luminous as the sun. How does the radius of Betelgeuse compare to the sun's radius? Why is Betelgeuse called a "red supergiant"?
Link: https://www.optotherm.com/emiss-table.htm - please show step by step explanation and solve this on paper so, it would be more easier for me to understand.
On one side of a diverging lens of focal length 37.1 cm, you position an object of height 2.42 cm somewhere along the principal axis. The resultant image has a height of 0.97 cm. How far from the lens is the object located? 38.9 cm 55.5 cm 88.8 cm 72.2 cm
Pls show the edge view of two triangles in a single reference plane...kindy explain the steps
20.Components of some computers communicate with each other through optical fibers having an index of refraction n = 1.55. What time in seconds is required for a signal to travel 0.2 m through such a fiber?
I have been stuck on this problem for while thar area is 779.1 mm^2 sigma_x is 120.6497159 sigma_y is 0 and tau_xy is 0. Beta is 20 degrees
This problem comes from Introduction to Graphics Communications for Engineers 4th Edition page 64 #2 could you help me sketch the isometric view given the 3 standard views
On the part shown, specify a geometric control to make the left surface in the front view perpendicular to the bottom surface within .005 total, and what would the the flatness on the left surface of the part above be? Can a datum or feature modifier be applied to this feature control frame? why or why not?
The given casted component is in isometric view ,for the casted component ,sketch the Orthographic view using creo software Note : only CREO PARAMETRIC 3.0 ,no hand drawing