The drawing shows a wire composed of three segments, AB, BC, and CD. There is a current of 1 = 2.0 A in the wire. There is also a magnetic field B (magnitude = 0.26 T) that is the same everywhere and points in the direction of +z axis. The lengths of the wire segments are LAB = 1.2 m, LBC = 0.3 m, and LcD = 0.3 m. Find the magnitude of the force that acts on each segment. A +Z D B I B +y

The drawing shows a wire composed of three segments, AB, BC, and CD. There is a current of 1 = 2.0 A in the wire. There is also a magnetic field B (magnitude = 0.26 T) that is the same everywhere and points in the direction of +z axis. The lengths of the wire segments are LAB = 1.2 m, LBC = 0.3 m, and LcD = 0.3 m. Find the magnitude of the force that acts on each segment. A +Z D B I B +y

Physics for Scientists and Engineers with Modern Physics

10th Edition

ISBN:9781337553292

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter30: Faraday's Law

Section: Chapter Questions

Problem 37AP

See similar textbooks

Similar questions

Within the green dashed circle show in Figure P30.21, the magnetic field changes with time according to the expression B = 2.00t3 4.00t2 + 0.800, where B is in teslas, t is in seconds, and R = 2.50 cm. When t = 2.00 s, calculate (a) the magnitude and (b) the direction of the force exerted on an electron located at point P, which is at a distance r = 5.00 cm from the center of the circular field region. (c) At what instant is this force equal to zero? Figure P30.21
Review. A rod of mass 0.720 kg and radius 6.00 cm rests on two parallel rails (Fig. P28.23) that are d = 12.0 cm apart and L = 45.0 cm long. The rod carries a current of I = 48.0 A in the direction shown and rolls along the rails without slipping. A uniform magnetic field of magnitude 0.240 T is directed perpendicular to the rod and the rails. If it starts from rest, what is the speed of the rod as it leaves the rails? Figure P28.23 Problems 23 and 24.
Sketch a plot of the magnitude of the magnetic field as a function of position r for a coax (Fig. P31.27).
Two frictionless conducting rails separated by l = 55.0 cm are connected through a 2.00- resistor, and the circuit is completed by a bar that is free to slide on the rails (Fig. P32.71). A uniform magnetic field of 5.00 T directed out of the page permeates the region, a. What is the magnitude of the force Fp that must be applied so that the bar moves with a constant speed of 1.25 m/s to the right? b. What is the rate at which energy is dissipated through the 2.00- resistor in the circuit?
In Figure P20.65 the rolling axle of length 1.50 m is pushed along horizontal rails at a constant speed v = 3.00 m/s. A resist or R = 0.400 is connected to the rails at points a and b, directly opposite each other. (The wheels make good electrical contact with the rails, so the axle, rails, and R form a closed-loop circuit. The only significant resistance in the circuit is R.) A uniform magnetic field B = 0.800 T is directed vertically downward. (a) Find the induced current I in the resistor. (b) What horizontal force F is required to keep the axle rolling at constant speed? (c) Which end of the resistor, a or b. is at the higher electric potential? (d) Alter the axle rolls past the resistor, does the current in R reverse direction? Explain your answer. Figure P20.65
A long, straight wire going through the origin is carrying a current of 3.00 A in the positive z-direction (Fig. P19.44). At a point a distance r = 1.20 m from the origin on the positive x-axis, find the (a) magnitude and (b) direction of the magnetic field. At a point the same distance from the origin on the negative y-axis, find the (c) magnitude and (d) direction of the magnetic field. Figure P19.44
A magnetic field exerts a torque on each of the current-carrying single loops of wire shown in Figure OQ29.13. The loops lie in the xy plane, each carrying the same magnitude current, and the uniform magnetic field points in the positive x direction. Rank the loops by the magnitude of the torque exerted on them by the field from largest to smallest.
Figure P23.15 shows a top view of a bar that can slide on two frictionless rails. The resistor is R = 6.00 , and a 2.50-T magnetic field is directed perpendicularly downward, into the paper. Let = 1.20 m. (a) Calculate the applied force required to move the bar to the right at a constant speed of 2.00 m/s. (b) At what rate is energy delivered to the resistor? Figure P23.15 Problems 15 through 18.