The driver attempts to get the car out of the mud by exerting a perpendicular force of 610.0 N, and the distance she pushes in the middle of the rope is 1.00 m while she stands 6.00 m away from the car on the left and 6.00 m away from the tree on the right. What is the tension T in the rope, and how do you find the answer?

Q: 3/2 A carpenter carries a 12-lb 2-in. by 4-in. board as shown. What downward force does he feel on…

A:

Q: Situation 2: Find the minimum force P required to just pull out box B. Also, find the tension of the…

A:

Q: It is required to climb a cylinder one step, rolling without slipping; Said cylinder has a weight W…

A:

Q: Trina is a gym goer with a leg length of 84 cm. Suppose that she is in the gym doing straight leg…

A: Solution: Given data: L = 84 cm W = 10 lbs

Q: A) A 1.2 kg block slides down a frietionless incline with a slope angle of 42°, starting from a…

A: As per the Bartleby answering guidelines we are supposed to answer first Question only. Please…

Q: A wheel of mass M has radius R. It is positioned vertically on the floor and you exert a horizontal…

A:

Q: Q4-Two blocks A and B of weight 350 N and 600 N. respectively are connected by a cord that passes…

A:

Q: An engineer trying to determine whether her crane will tip over when attempting to lift a 13K load.…

A: Given data as per question Load to be lifted = 13 k weight of counterweight = 15 k weight of crane…

Q: 2. Draw the free body diagram of the following situations.

A:

Q: 3. After a mishap, a 76.0-kg circus performer clings to a trapeze, which is being pulled to the side…

A: Given data: The mass of circus performer, m = 76.0 kg. Calculate the weight of the circus…

Q: A frictionless slope is fixed to the ground. There is a ball that is completely stationary. Two…

A:

Q: FIGURE BELOW shows a scale constructed using the 10 kg mass of cylinder, the 2 kg pan P, and the…

A:

Q: m

A: Given data: The mass of the sphere is m = 1 kgThe radius of the sphere is R = 0.5 mThe height of the…

Q: A 40 kg boy climbs up an 8-meter ladder. The ladder weighs 700-N and rest against a vertical wall in…

A: m=40kg M = 700N  L=8m  Angle with ground = 70°

Q: Block A has a weight of 60 lb and block B has a weight of 10 lb. Neglect friction and the mass of…

A:

Q: Neglecting friction and the weights of the members, compute the magnitudes of the pin reactions at A…

A: A pin support will exert both the horizontal and the vertical component of reaction forces. If a…

Q: a uniform ladder 8 meters long and weighing 350 N rest against a smooth vertical wall at an angle of…

A: Given: Length of the ladder is 8 m. Weight of the ladder is 350 N. Angle from the vertical wall is…

Q: A 210-kg mass is supported as shown. Calculate the angle a and the force P. (Neglect friction in all…

A: Given :  m = 210 Kg

Q: A uniform ladder 8 meters long and weighing 350 N rest against a smooth vertical wall at an angle of…

A: Free Body diagram Let F is the horizontal force necessary at the base to keep the ladder from…

Q: A 0.05KN ball is placed on a vertical circle whose length of the cord is 1.80 m. Compute the height…

A:

Q: The uniform crate shown below weighs 200lb. It is pulled up the incline by a counterweight W of…

A: Assume this diagram and the FBD,

Q: A rope with two mass-less platforms at its two ends passes over a fixed pulley as shown in the…

A: The minimum value disc required on the right side: m = 3 disc

Q: When activated by the force P,the gripper on a robotic arm is able to pick up objects by applying…

A: When push or the pull applied on the object, then it has the tendency to change the state of the…

Q: A plane moves at 820km/h as it makes a horizontal circular turn of radius 15.0 km. a. Draw a free…

A:

Q: 11.) In the figure shown, if u = 0.30 under both blocks and A weighs 400 lb, find the maximum weight…

A:

Q: Block A weighing 6 kN rests on a horizontal plane and supports on top of it another block of…

A: Given values are - WA=6kN, WB=1kN , μ=0.3 The FBD of the block A and B is given below -

Q: A block sits on a plane, and there is friction between the block and the plane. The plane is…

A: Graphical representation of forces may be applied externally, reactions ( normal force, tension,…

Q: Q6: A 60 kg cupboard is to be shifted to the right, p, between cupboard and floor is 0.35 as shown…

A:

Q: In the figure, the crate A weighs 801lb, the angle of the incline plane is 25° and the coefficient…

A: Given information: The weight of the create A (WA) = 80 lb The inclination of the plane (θ) = 250…

Q: calculate the intensity of the forces. Calculate the intensity of the tractive force on the wire,…

A:

Q: A 12.0 kg weight hangs from a 7.50 m pole as illustrated in the diagram.  The pole has a mass of 8.0…

A: Write the given value using suitable variables. Here W signifies given weight, L signifies pole…

Q: The uniform crate shown in the figure weighs 600 lb. It is pulled up the incline by a counterweight…

A: To find: The maximum and minimum values of d so that the crate does not tip over as it slides up the…

Q: Find the forces in the cables AB, BC, CD, DE, and force in the spring CF in terms of P. (a is an…

A:

Q: a ladder whose length L is 12 m and whose mass m is 45 kg rests against a wall. Its upper end is a…

A: Given Data The length of the ladder is: L=12 m Mass of the ladder is: m=45 kg The upper end…

Q: A small ring Pis threaded on a fixed smooth horizontal rod AB. Three horizontal forces of magnitudes…

A:

Q: Find the rod forces in the truss system, whose dimensions and loading condition are given in the…

A:

Q: A block weighing 100 N rests on a floor whose coefficient of friction with the block is 0.3. Find…

A:

Q: MA = 2 T (a)

A:

Q: Blocks A, B, and C are placed as in Fig. and connected by ropes of negligible mass. Both A and B…

A: The free body diagram for the block A and B is (a) Here T1 is the tension in the rope between block…

Q: A roller of weight 500 N has a radius of 120 mm and is pulled over a step of height 60 mm by a…

A:

Q: Problem 4.9 Figure 4.56 illustrates a person who is trying to pull a block on a horizontal surface…

A:

Q: 2|A block with a mass of m = 5.5kg, is supported by two massless pulleys as shown to the right →.…

A:

Q: A uniform ladder 8 meters long and weighing 350 N rest against a smooth vertical wall at an angle of…

A: Free Body Diagram

Q: . Spring is hung vertically, and an object of mass (m) is attached to its lower end. The spring…

A: Given data mass of object = m spring stretches by distance = d  We have to find the work done by the…

Q: Figure 4 shows a 27-kg concrete block that has been positioned on a 20° incline. As shown in the…

A: Note: As per company policy, answer of first three sub-parts of the question are provided here. You…

Q: A car of weight w is wrongly parked along the street. The MMDA tows it as shown in the figure below.…

A: Given: To  draw the free body diagram and to find the tension in the cable and the force exerted by…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.