The dynamic system is initially at rest. The rod has a mass of m=0.5kg and a length of L=1m. The CG of the rod is located at G, and the rod is rotated about the point O, a distance, h=0.25m, away from point G.  At the time of releasing find a. Acceleration at the CG (point G)  b. Reaction at O (Use moment of inertia of the rod I= mL2/12)

Q: for the following find f (-3.5) Using Lagrange Polynomials -4 0₁ 6 -3.64 1 -3

A: To find: The value of f(-3.5). Given: The following data is given. xo=-4, x1=-3.64, x2=-3yo=0,…

Q: Find the Velocity of arocket by using Styling formula + = 150 sec +(s) v (mile/) Go 120 180 0.0824…

A: To find: The velocity of a rocket. Given: The following data is given.

Q: Air is compressed in a compressor through the purely polytropic, purely isothermal, and intercooling…

A: The process that is purely polytropic is 1-X-2" Answer: C. 1-X-2"

Q: A drive shaft running at 2500 rpm has outer diameter of 60mm and inner diameter of 40mm. The…

A:

Q: One of the type of Tunnel washers is 777 b 17 Od Top transfer Forward tilt Side load Auto carte…

A: Tunnel washer: A tunnel washer, also known as a continuous batch washer, is a large industrial…

Q: The following data was obtained as a result of tensile testing of a standard 0.505 inch diameter…

A: To find: The modulus of elasticity and plot the stress and strain diagram. Given: Table for load and…

Q: what are some Observation and Description of Experimental Setup of key failure using bending test

A: Given: To find: Observation and description of experimental setup

Q: Select all proper statements below to explain that the isentropic process is not necessarily an…

A: To prove that not all isentropic process are reversible adiabatic

Q: If the allowable bending stresses for a beam in one application is 6 kip/in² in tension. The…

A: Given data:- Beam section=W8×40 Allowable bending stress (σ)=6 kip/in2 To find:-Allowable maximum…

Q: A row of long cylindrical power cables that are spaced 2 cm evenly apart is placed in parallel with…

A: Given data: s=2 cmD=1 cmThermal conductivity of the plate k=15 W/mkThickness of the plate, t=5…

Q: 2. 8" X Y Y 6" -X

A:

Q: A small circuit board is fitted with a heat sink of a base of 4-cmx4-cm. The heat sink contains 20…

A:

Q: 50 mm OW. 50 mm 50 mm 350 mm 50 mm Determine the moment of inertia about the centroidal x-axis shown…

A:

Q: To confirm that a double-pane window is indeed better than a single-pane window, you ran some tests.…

A:

Q: Full explain this question and text typing work only      We should answer our question within 2…

A: Given: To find: Explanation

Q: There is a CNC system with one sensor and one actuator. Draw a block diagram f. CNC system with a…

A: Given: CNC system with one sensor and one actuator To find: Block diagram Explain

Q: Problem #3: Perform single plane balancing calculations of the following tire rim. HINT; F₁ +5² +5²…

A: Given data, The masses and radial distance of the masses are tabulating below Mass in oz, m…

Q: Consider a moist air mass at P-950mb pressure with water vapor mixing ratio w=4x10. Calculate the…

A: Given data:- Total Pressure of moist air (PT)=950 mb Water Vapor mixing ratio=4×10-3 To find:-Water…

Q: Find the moment of inertia I y about the y' axis. y'

A:

Q: QUESTION 10 The Kelvin-Planck and Clausius statements of thermodynamics are equivalent. In order to…

A: Option (B) is correct,remaining are incorrect.

Q: 1. 0 100 kN/m 3 100 KN 5 7 100 kN/m 10 ►x (m)

A:

Q: 2' 1000# 13 21 c 2' 2' 100*/ft E a) What is the shear force @ 5¹ rt. of A ? Ans. in # rounded off to…

A:

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A:

Q: A thin plastic membrane is used to separate helium from a gas stream. Under steady-state conditions…

A:

Q: Given that the PE at A is 20 kJ and KE at A is 5.0 kJ. What is the KE at B if the height at B is 2.0…

A: Potential energy at A, PE(A) = 20 kJ or 20000 J Kinetic energy at A, KE(A) = 5 kJ or 5000 J Height…

Q: 13-13. Figure P13.13 shows an adjustable platform used to load and unload freight trucks. Currently,…

A:

Q: Liquid fuel of kinematic viscosity 2.37x10-6 flows through the pipe of diameter 15 cm. Determine the…

A:

Q: shaft A, made of AISI 1010 hot-rolled steel, is welded to a fixed support and is subjected to…

A:

Q: Which of the following is TRUE on describing reverse-engineering: O Reverse engineering gives a…

A: Option (3) is correct, remaining are incorrect. Reverse engineering, sometimes called back…

Q: A large wood products company is negotiating a contract to sell plywood overseas. The fixed cost…

A:

Q: How would you solve this manually without an equation solver

A:

Q: In a steady adiabatic flow through a duct with no shaft/electrical work and no change in elevation…

A:

Q: In a 2D dimension incompressible flow , if the fluid velocity components are given by u = x-4y , v =…

A: Given:The fluid velocity components are given as:u=x-4yv=-4x

Q: SA PROBLEM 16.18 A prototype rotating bicycle rack is designed to save space train station. The…

A:

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A:

Q: Required information A Diesel cycle has a compression ratio of 22 and begins its compression at 87…

A:

Q: ! Required information Consider a water-to-water counterflow heat exchanger with these…

A:

Q: Consider a 320 mm x 320 mm window in an aircraft. For a temperature difference of 80°C from the…

A:

Q: Find the fluid force (in lb) on the vertical plate submerged in seawater (use 64 pounds per cubic…

A: Introduction We shall compute the force on a vertically submerged plate in seawater in this issue.…

Q: The sketch shows a flat plate aligned parallel to an incompressible airstream. Assume a velocity…

A: Given Data: flat plate aligned parallel to an incompressible airstream Find: Assume a velocity…

Q: 7.1. When 0.001 9 m³/s of water flow in a 76 mm pipeline at 21°C, is the flow laminar or turbulent?

A:

Q: ! Required information A Diesel cycle has a compression ratio of 22 and begins its compression at 87…

A: Given Data- Compression ratio r=22 P1=87KPa , T1=15'C T3=1200'C We have to find thermal efficiency

Q: Suppose linear elastic spring is compressed 2cm from its at-rest position, and then the spring is…

A: Given data x1=2 cmx2=5 cmk=1800 N/cm Here, k is the spring constant. Now we have to find out the…

Q: The single tank system (Figure 1) has been modelled by the first order differential equation given…

A: Given: To find: Expression to show how the level in tank will vary

Q: Question 1. A quarter car rig has been designed with the following parameters: m, = 231 kg, m, 29…

A: To find: The body bounce and wheel hop frequency of the quarter acr rig. Given: Un-sprung mass, mu =…

Q: A thin bar of length L = 3 meters is situated along the x axis so that one end is at x = 0 and the…

A: Given: Length, L=3m Thermal diffusivity, k=0.4 Initial temperature, f(x)=100-10x Boundary…

Q: Which one of the statements is correct? The Kelvin-Planck and Clausius statements of thermodynamics…

A: Introduction The second law of thermodynamics is based on two different statements one is known as…

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A: Given data as per the question length of square 80 mm The diameter of semi circle = 45 mm

Q: Using Newton's second law, the movement of a body in a viscous fluid can be modeled. For this case…

A:

Q: A cylindrical rod of stainless steel is insulated on its exterior surface except for the ends. The…

A: According to question:- Temperature distribution within the rodT=a-bxLDiameter of the…

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.