The EGL and HGL of a system are shown below. Assume that the fluid is water and a = 1 in all locations. a) Calculate the velocities at points A, C and E. b) Calculate the total loss due to friction from point A to F. c) Sketch the physical system that could yield the conditions shown from A to F. 61.26m 60.96m 60.04m 59.74m N58.25m 53.37m 43.62m 40.87m 40.26m 39.96m 40.57m 38.74m BC DE

The EGL and HGL of a system are shown below. Assume that the fluid is water and a = 1 in all locations. a) Calculate the velocities at points A, C and E. b) Calculate the total loss due to friction from point A to F. c) Sketch the physical system that could yield the conditions shown from A to F. 61.26m 60.96m 60.04m 59.74m N58.25m 53.37m 43.62m 40.87m 40.26m 39.96m 40.57m 38.74m BC DE

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A square plate with 0.5m side length is placed in a water tank so that its centroid is in a depth of2.9m. If the flat surface of plate is placed in vertical plan and top edge is parallel to the freesurface, calculate the distance to the horizontal pressure force acting on one side of the surfacefrom the free surface.(a) 2.907 m(b) 3.000 m(c) 2.900 m(d) 3.010 m
Points A and B are 5km apart along a new 60cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140KPa greater than at A. f=0.019. Determine the head loss in meters choices: 7.52 2.75 5.27 7.25 Determine the flow rate in lit/sec choices: 822.55 885.22 228.55 522.88
From Figure 7, determine (a) the difference in pressure (b) the difference in piezometric head between points A and B. The elevations zA and zB are 10 m and 11 m, respectively, ℓ1 = 1 m, and the manometer deflection ℓ2 is 50cm.
1. Determine the equations of slope and deflection. 2. Determine the slope and deflection at point 3m from point A. E =210 GPa. 100 | Cross section 6KN.m 2m B8KN 2 kN/m 2m T ) B8KN 2m
Find the volume of water in the horizontal cylindrical tank if it is 7/8 full. Radius of tank is 600mm and the length of the tank is 5m. If tank is placed in a vertical position, what is the depth of water inside the tank? A. 5.13m B. 4.38m C. 4.71m D. 3.37m
The elevations of the ski jumping hill are as follows: hA = 44 mhB = 1.6 mhC = 4.9 m If the velocity of a ski jumper is measured to be 27.9 m/s at position B, what will be the launch velocity (in m/s) at position C.
A horizontal Venturi meter 45cm by 60cm is used to measure the flow of air through a 60cm pipeline. A differential gage connected to the inlet and throat contains water which is deflected 10cm. considering the specific weight of air as 12.60 N/m3 , find the flow of air. Neglect head losses
Fluid mechanics question. As shown, a round viewing window of diameter, D=0.8m is situated in a large tank of seawater (S=1.03). The top of the window is 1.2m below the water surface, and the window is angled at 60o with respect to the horzontal. Find the hydrostatic force acting on the window and locate the corresponding CP.
A triangular plate of 1 m base and 1.5 m altitude is immersed in water. The plane of the plate is inclined at 30° with water surface while the base is parallel to and at a depth of 2 m from the water surface. Calculate the position of the center of pressure in meters. a.2.987 b.1.896 c.3.234 d.2.264
Please indicate the given and illustration A cylindrical vessel 3m high and 1.5m in diameter is filled with water to a depth of 2.5m. In its side is a 50mm circular orifice C = 0.60 placed 300mm above the bottom of the vessel. If the vessel be rotated about its own axis at 60 rpm and the water allowed to escape through the orifice for a period of 3 minutes, determine the following: A) Compute the difference in elevation, in meters, of the water surface at the center and at the periphery of the tank at end of the 3 minutes B) How deep will the water stand in the vessel if brought to rest?
45. A 1-meter-diameter cylinder is connected to a 2-meter-wide rectangular gate as shown. The gate is to open when the water level, h, drops below 2.5 m. Use y = 4 m., d = 1 m. Determine the hydrostatic force acting on the gate when h = 2.5 m. a. 156.96 b. 61.3125 c. 24.525 d. 96.810
Gate AB is 1.0 m long by 1.5 m wide. What is the position X of its center pressure in mm?