The electromagnetic wave radiated from an antenna of resistance 151 ohms is denoted by the expression S(t) = Vc(1+Vm sin2 TE fmt) sin2 Tfct; where Vm = 4.5 V, Vc = 20.5 V,fm= 97KHZ and fc = 56MHZ. Find() the expression for the message signal ((1) the expression for the carrier(ii) Draw its spectrum and find the sidebands (

given signal is amplitude modulated signal s(t)=[Ac+Amcos(2πfmt)]cos(2πfct) after comparing we can…

The electromagnetic wave radiated from an antenna of resistance 151 ohms is denoted by the expression S(t) = Vc(1+Vm sin2 Tt fmt) sin2 Ttfct; where Vm = 4.5 V, Vc = 20.5 V, fm= 97KHZ and fc = 56MHZ. Find () the expression for the message signal ( (11) the expression for the carrier ( (iI) Draw its spectrum and find the sidebands (3

The electromagnetic wave radiated from an antenna of resistance 151 ohms is denoted by the expression S(t) = Vc(1+Vm sin2 Tt fmt) sin2 Ttfct; where Vm = 4.5 V, Vc = 20.5 V, fm= 97KHZ and fc = 56MHZ. Find () the expression for the message signal ( (11) the expression for the carrier ( (iI) Draw its spectrum and find the sidebands (3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question2) Suppose we wish to transmit a cosine signal x(t)=cos(2π×6000t)x(t)=cos⁡(2π×6000t). If this signal is directly sent by an antenna, find the wavelength of the transmitted electromagnetic wave. How long the antenna size should be? Is it practical to have an antenna of that size? Consider we decide to modulated the signal using amplitude modulation. A carrier signal of c(t)=cos(2π×250000t)c(t)=cos⁡(2π×250000t). If the modulated signal is in the form of s(t)=(A+x(t))×c(t)s(t)=(A+x(t))×c(t), where AA is the constant added to the signal to make it always positive, choose the constant AA. Draw the frequency domain representation of the baseband and the modulated signal. Let's assume we want to do amplitude demodulation in the receiver side. Draw the clock diagram of the demodulator including a downconverter, a low pass filter, and the detector. Choose the cut-off frequency for the low-pass filter. (Note the cut-off frequency in a low-pass filter is the frequency which the filter…
The radar antenna, which is used as both transmitter and receiver, is at the operating frequency of 5GHz. It has a gain of 150 (dimensionless). The antenna emits 100kW of power and 3m2 at 1km for maximum directional radiation and reception a radar cross-sectional area of is aligned with the target. The received signal is polarization compatible with the emitted signal.Find the received power.
A satellite in synchronous orbit is used to communicate with an earth station at a distance of 7.6 ×10^7 m. The satellite has an antenna with a gain of 15 dB and a transmitter power of 3 W. The earth station uses an antenna with gain 50 dB. The frequency band is at f = 9.8 GHz. What is the free space path loss in dB? Also, determine the received power level at the output of the receiver antenna in dBW.
A surface search radar has the following characteristics:i. Frequency = 5 GHz (C-Band - vertical polarization)ii. Peak power = 5 kWiii. Circular phased-array – diameter = 1.00 metersiv. Noise Figure = 2 dBv. Total System Losses = 10 dBvi. Duty factor = 5%vii. Dwell length or processing time = 1.0 msviii. Bandwidth = 1 MHz Using Matlab Plot the SNR (in dB, y-axis) versus Range (from 1 km to 50 km) for a target with a 1m2 RCS. Assume maximum antenna gain towards the target, antenna gain is the same fortransmit and receive, and unity propagation. If a SNR of 15 dB is required to detect the target, atwhat range is the target first detectable?
The PCB monopole antenna shown in figure below is required to be designed for Bluetooth Low Energy wireless mouse operating at 2.45 GHz. What should be the length of the antenna trace in mm. Assume the substrate of the PCB is foam (dielectric constant = 1)
2.) The power density is 4 mW/m² at some distance R from an isotropic antenna. The isotropic antenna is replaced with a different antenna and the power density measured is now 60 mW/m² at the same distance R. What is the gain (in dB) of the second antenna? 3.) The received power at an airplane is calculated as Pr=-43 dBm at a range of 13 miles using free-space propagation. Determine the received power (in dBm) at a range of 52 miles.
An antenna has a radiation resistance of 150ohm and is fed with an RMS current of 5A. If the antenna gain is 6 dB in a given direction, determine the power density and electric field strength at a receiving antenna 60 km away in this direction. Given that the effective area of the receiving antenna is 1.5m2, calculate the received power.
The transmit power is 20 dB, the transmit antenna gain is 2 (in linear scale), the receiveantenna gain is 3 (in linear scale), the carrier frequency is 300 kHz, the transmit antenna heightis 10 meters, the receive antenna height is 1 meter, the distance between the transmitter andreceiver is 1 km, L = 1. The transmission environment is air (the path loss exponent is 2). Usethe free space propagation model.a. Calculate the receive power in dBm.b. Calculate the path loss in dB.
Find the far-field condition of a satellite dish antenna of dimension 60 cm operating at 12 GHz.
A TE10 wave at 10 GHz propagates in a brass σc=(1.57x10^7 S)/m rectangular waveguide with dimension a=1.5 cm and b=0.6 cm,which is filled with teflon εr=2.6,μr=1σd=(10(_^(-15))S)/m.calculate the dielectetric loss,conductor loss and the overall attenuation of the waveguide over a distance of 10 m.
A 10 GHz Microwave link is designed to connect two points which has 10 km distance. The transmitter effective radiated power is 50 dBW. Calculate the received signal power, PR , and voltage, VR , if the receiving antenna gain is 10 dB and the input impedance is 50 ohms.
A 9GHz signal propagates inside the rectangular waveguide that is filled with lossy dielectric material with dielectric conductivity 10-15 mhos/m, dielectric permittivity 2.2 and dielectric permeability 1.0. Use the appropriate formula to determine the guide attenuation factor if the cutoff frequency is 4.5GHz.