The elements of a rear suspension for a front-wheel-drive car are shown in the figure. Determine the magnitude of the force at each joint if the normal force exerted on the tire has a magnitude of 3170 N. 51 mm 210 mm F 115 mm 67 mm D 270 mm JA |E \B 265 195 mm mm 3170 N 63 mm Answers: A = i N B = i 3840 N C = i 1520 D = i 1520 N E = i N F = i N z z z

The elements of a rear suspension for a front-wheel-drive car are shown in the figure. Determine the magnitude of the force at each joint if the normal force exerted on the tire has a magnitude of 3170 N. 51 mm 210 mm F 115 mm 67 mm D 270 mm JA |E \B 265 195 mm mm 3170 N 63 mm Answers: A = i N B = i 3840 N C = i 1520 D = i 1520 N E = i N F = i N z z z

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.59P: How many turns of rope around the capstan are needed for the 40-lb force to resist the 8000-lb pull...

See similar textbooks

Similar questions

Determine the normal tension of the cylinder piston rod (diameter 32mm). The clamping force of the pliers is 6000N. The dimensions of the structure are: x1 = 10 mm x2 = 120 mm y1 = 110 mmy2 = 798 mm Use the units [N, mm], ie the answer comes in MPa !!! Please enter a numeric value only !!
The platform scale consists of a combination of third and first class levers so that the load on one lever becomes the effort that moves the next lever. Through this arrangement, a small weight can balance a massive object. If a 3kg counterweight S is used to balance a 120kg load L, what is the value of 'x'? Draw all pertinent FBDs. Use g=9.806 m/s2.
The block brake consists of a pin-connected lever and friction block at BB. The coefficient of static friction between the wheel and the lever is μsμs = 0.3, and a torque of 5 N⋅mN⋅m is applied to the wheel. Determine if the brake can hold the wheel stationary when the force applied to the lever is (a) PP = 30 NN, (b) PP = 70 NN. Draw the free-body diagram of the wheel. Draw the vectors starting at the black dots. The location and orientation of the vectors.
For the same question, the Driving force (pressing force) of the Nut will be measured with the Torque wrench. While tightening the nut, the contact surface rubs against the fixed surfaces. Accordingly, how much MOMENT do we need to read from the Torque wrench in order to create a force of Fçak=1101 kgf? (Given: Screw pitch M30, Root diameter d1=25.8 mm) Outer diameter of the friction surface under the nut D42 mmFriction coefficient μ=0.6
How many turns of rope around the capstan are needed for the 40-lb force to resist the 8000-lb pull of a docked ship? The static coefficient of friction between the capstan and the rope is 0.25.
The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft on the right. Compression springs between the clutch housing and the pressure plate provide the necessary pressure on the friction surface. The splines prevent the clutch plate from rotating relative to the output shaft. If Ri=4 in. and R0=9 in., determine the total force that must be applied to the pressure plate by the springs if the clutch is to transmit a torque of C=56lbft when it is new.
For the spring assemblage shown below, determine the displacement at node 2 and the forces in each spring element. Also determine the force F3. Given: Node 3 displaces an amount 8 = 12.5 mm in the positive x direction because of the force F3 and k1 k2 175 kN/m.
Figure 1 shows a railroad wagon axle and forces acting over it. There are two disc brakes on the wagon axle. Since the wagon wheels are not driven wheels, the load bearing element to which the wheels are connected is called axles. The axle is supported at both ends with bearing A and bearing B and the the weight of the wagon (G) is evenly distributed on both bearings (as G/2). During braking, two disc brakes on the axle are applied Ff force and Ft friction forces are formed on the wheels. Therefore the axle is forced to bend in the vertical direction with the effect of wagon weight (G) and wheel reaction forces (Rt), and in horizontal direction with the effect of braking (Ff) and wheel friction (Ft) forces. At the same time, the axle is forced under torsion because of Ff and Ft forces. GIVEN:Shaft material : 50CrMo4 Wheel material : GS 60 Brake discs’s material: 15Cr3 All the radiuses : 5 mm Average roughnesses for press fit surfaces: Ra =6.3 μm Wheel speed: = 500 d/d Wagon weight per…
A ladder carried by a fire truck is 20.0 m long. The ladder weighs 3400 N and its center of gravity is at its center. The ladder is pivoted at one end (A) about a pin (Fig. ); ignore the friction torque at the pin. The ladder is raised into position by a force applied by a hydraulic piston at C. Point C is 8.0 m from A, and the force F S exerted by the piston makes an angle of 40° with the ladder. What magnitude must F S have to just lift the ladder off the support bracket at B? Start with a free-body diagram of the ladder.
Two bodies is connected in point C, are supported by rigid underlay at an angle α. F is the force acting on right body. We are considering the weight of bodies G and the friction between the bodies and the underlay. Length of bodies l=2000mm.    G1= 160 N, G2= 180 N, α = 30° Find:  1.) Find the magnitude of the force so that it slips on the underlay 2.) Draw the dependence of the force F as a function of the coefficient of friction f (in the range 0-0.5)
A 415 kg safe is hanging from the apparatus below. Determine the tension in the cable. Dimension a=1.9 m and dimension b=2.5 m. The mass of the beam is 85 kg. Use g = 10 N/kg. Hint: Take torques about the hinge and use the perpendicular lever arm version of the torque equation (the sin theta version will work but will require more calculation).
How much work is done by the force in the spring when the slender rod rotates clockwise about the fixed pin support at O from the vertical position (where AB is horizontal) to the horizontal position? The spring has a stiffness of k = 125 N/m and an unstretched length of 0.15 m. Take d1= 0.29 m and d2= 0.85 m. Choose the correct answer. a) 94.9 Joule b) 99.9 Joule c) -99.9 Joule d) 0 Joule e) -94.9 Joule