The figure below shows a top view of a bar that can slide on two frictionless rails. The resistor is R = 5.60 2, and a 2.50-T magnetic field is directed perpendicularly downward, into the page. Let { = 1.20 m.BinRSapp(a) Calculate the applied force required to move the bar to the right at a constant speed of 2.10 m/s.|N (to the right)(b) At what rate is energy delivered to the resistor?

Given value--- resistance R = 5.60 ohm. magnetic field = 2.50 T . length = 1.20 m. velocity = 2.10…

The figure below shows a top view of a bar that can slide on two frictionless rails. The resistor is R = 5.60 n, and a 2.50-T magnetic field is directed perpendicularly downward, into the page. Let { = 1.20 m. Bin R app (a) Calculate the applied force required to move the bar to the right at a constant speed of 2.10 m/s. N (to the right) (b) At what rate is energy delivered to the resistor?

The figure below shows a top view of a bar that can slide on two frictionless rails. The resistor is R = 5.60 n, and a 2.50-T magnetic field is directed perpendicularly downward, into the page. Let { = 1.20 m. Bin R app (a) Calculate the applied force required to move the bar to the right at a constant speed of 2.10 m/s. N (to the right) (b) At what rate is energy delivered to the resistor?

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter23: Faraday’s Law And Inductance

Section: Chapter Questions

Problem 15P: Figure P23.15 shows a top view of a bar that can slide on two frictionless rails. The resistor is R...

See similar textbooks

Similar questions

The conducting rod shown in the accompanying figure moves along parallel metal rails that are 25-cm apart. The system is in a uniform magnetic field of strength 0.75 T, which is directed into the page. The resistances of the rod and the rails are negligible, but the section PQ has a resistance of 0.25 . (a) What is the emf (including its sense) induced in the rod when it is moving to tire right with a speed of 5.0 m/s? (b) What force is required to keep the rod moving at this speed? (c) What is the rate at which work is done by this force? (d) What is the power dissipated in the resistor?
Two frictionless conducting rails separated by l = 55.0 cm are connected through a 2.00- resistor, and the circuit is completed by a bar that is free to slide on the rails (Fig. P32.71). A uniform magnetic field of 5.00 T directed out of the page permeates the region, a. What is the magnitude of the force Fp that must be applied so that the bar moves with a constant speed of 1.25 m/s to the right? b. What is the rate at which energy is dissipated through the 2.00- resistor in the circuit?
A conducting single-turn circular loop with a total resistance of 5.00 is placed in a time-varying magnetic field that produces a magnetic flux through the loop given by B = a + bt2 ct3, where a = 4.00 Wb, b = 11.0 Wb/s2, and c = 6.00 Wb/s3. B is in webers, and t is in seconds. What is the maximum current induced in the loop during the time interval t = 0 to t = 3.50 s?
Show that the magnetic field at a distance r from the axis of two circular parallel plates, produced by placing charge Q(t) on the plates is Bind=02rdQ(t)dt
Is the work required to accelerate a rod from rest to a speed v in a magnetic field greater than the final kinetic energy of the rod? Why?
A metal rod of mass m slides without friction along two parallel horizontal rails, separated by a distance and connected by a resistor R, as shown in Figure P30.13. A uniform vertical magnetic field of magnitude B is applied perpendicular to the plane of the paper. The applied force shown in the figure acts only for a moment, to give the rod a speed v. In terms of m, , R, B, and v, find the distance the rod will then slide as it coasts to a stop. Figure P30.13
How many turns must be wound on a flat, circular coil of radius 20 cm in order to produce a magnetic field of magnitude 4.0105 T at the center of the coil when the current through it is 0.85 A?
Is Ampere’s law valid for all closed paths? Why isn’t it normally useful for calculating a magnetic field?
Within the green dashed circle show in Figure P30.21, the magnetic field changes with time according to the expression B = 2.00t3 4.00t2 + 0.800, where B is in teslas, t is in seconds, and R = 2.50 cm. When t = 2.00 s, calculate (a) the magnitude and (b) the direction of the force exerted on an electron located at point P, which is at a distance r = 5.00 cm from the center of the circular field region. (c) At what instant is this force equal to zero? Figure P30.21
A flat loop of wire consisting of a single turn of cross-sectional area 8.00 cm2 is perpendicular to a magnetic field that increases uniformly in magnitude from 0.500 T to 2.50 T in 1.00 s. What is the resulting induced current if the loop has a resistance of 2.00 ?
A rectangular loop of wire has dimensions 0.500 m by 0.300 m. The loop is pivoted at the x axis and lies in the xy plane as shown in Figure P28.34. A uniform magnetic field of magnitude 1.50 T is directed at an angle of 40.0 with respect to the y axis with field lines parallel to the yz plane. The loop carries a current of 0.900 A in the direction shown. (Ignore gravitation.) We wish to evaluate the torque on the current loop. (a) What is the direction of the magnetic force exerted on wire segment ab? (b) What is the direction of the torque associated with this force about an axis through the origin? (c) What is the direction of the magnetic force exerted on segment cd? (d) What is the direction of the torque associated with this force about an axis through the origin? (e) Can the forces examined in parts (a) and (c) combine to cause the Loop to rotate around the x axis? (f) Can they affect the motion of the loop in any way? Explain. (g) What is the direction of the magnetic force exerted on segment bc? (h) What is the direction of the torque associated with this force about an axis through the origin? (i) What is the torque on segment ad about an axis through the origin? (j) From the point of view of Figure P28.34, once the loop is released from rest at the position shown, will it rotate clockwise or counterclockwise around the x axis? (k) Compute the magnitude of the magnetic moment of the loop. (l) What is the angle between the magnetic moment sector and the magnetic field? (m) Compute the torque on the loop using the results to parts (k) and (l). Figure P28.34
The magnetic flux through a metal ring varies with time t according to (B = at3 bt2, where (B is in webers, a = 6.00 s3, b = 18.0 s2, and t is in seconds. The resistance of the ring is 3.00 . For the interval from t = 0 to t = 2.00 s, determine the maximum current induced in the ring.