The figure shows a system for delivering lawn fertilizer in liquid form. The nozzle on the end of the hose requires 169.00 kPa of pressure to operate effectively. The hose is smooth plastic with an ID of 25 mm. The fertilizer solution has a specific gravity of 1.13 and a dynamic viscosity of 2.69 x 103 Pa•s. If the length of the hose is 76 m. The coefficient of friction, f= 0.021 and the flow rate is 97 L/min. Required Determine the power delivered by the pump to the solution in kW, to the nearest 100th.

The figure shows a system for delivering lawn fertilizer in liquid form. The nozzle on the end of the hose requires 169.00 kPa of pressure to operate effectively. The hose is smooth plastic with an ID of 25 mm. The fertilizer solution has a specific gravity of 1.13 and a dynamic viscosity of 2.69 x 103 Pa•s. If the length of the hose is 76 m. The coefficient of friction, f= 0.021 and the flow rate is 97 L/min. Required Determine the power delivered by the pump to the solution in kW, to the nearest 100th.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
The velocity through the centre-line of a 150 mm diameter pipe conveying oil under laminar flow conditions is 3 m/s. The viscosity of the oil is 1.2 poises and its density if 900 kg/m3 . Confirm that the flow is laminar and determine (a) the quantity flowing in dm³/s, and (b) the shear stress in the oil at the pipe wall in N/m²
The block of weight W = 50 N is pulled by a weight W0 = 60 N along the surface of a table by means of an inextensible cable and a pulley. Between the block and the table there is a uniform layer of oil of viscosity m = 0.1 Pa-s and clearance h = 2 mm. The contact area is 0.01 m2. Find the terminal velocity U if the table is very long.
Shown in the figure, Fluid 1 is flowing in a horizontal tube and a U-tube manometer containing Fluid 2 is connected to point 1 and 2. The specific weights for Fluid 1 and 2 are and , respectively. Select the correct expression.___________ A. B. C. D. p1 = p2
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 ?2/? and SG=0.9. Find the frictional resistance exerted by the oil on the shaft in Newtons (N).
The reduced elbow shown in the figure is part of a distribution system for a fluid whose density is 0.85 and which is in a vertical plane. If the manometer at point 1 indicates 245 kPa, and the flow rate at point 1 is 0.060 m/s. a) Calculate the reactions at "x" and "y" at A to keep the elbow in place
A skater weighing 500 N skates at 10 m/s and is supported by an average skating area of 10 cm2. If the viscosity of water is 1 centipoise and the coefficient of friction between skates and ice is 0.02, then find the thickness of thin film of water existing between the skates and the ice. Follow the methodologies in solving the problem; Given : Required: Schematic Diagram: Solution:
A 10-in diameter plunger slides in a 10.006-in diameter cylinder, the annular space being filled with oil having a kinematic viscosity of 0.004 ft²/s and specific gravity of 0.85. If the plunger moves at 0.6 ft/s, find the frictional resistance when 9ft is engaged in the cylinder.
2) The horizontal pipe of diameter 240 mm is suddenly enlargement to a diameter of 480 mm. if the pipe carries water at 325 liters/sec, calculate the (i) Head loss to sudden enlargement,(ii) Pressure loss across the enlargement (p1-p2).
A certain amount of water (H2O) flows permanently into the pipe venturi(image2) in the figure next to it. In the stretch considered between (1) and (2), it is assumed the losses by friction that were despicable and the uniform properties in the sections are assumed. The entrance area is A1 while that of throat is A2 (A1 > A2). A pressure gauge whose manometric fluid is Mercury Hg (YHg> YH2O) is connected between the input sections and the throat. Show, without omitting any calculation steps that the flow rate at the input (1) is given by(image1):
The water levels in the reservoirs are constant in the three reservoir systems given below, where local losses are neglected. How many meters is the piezometer height at the node (D)? The fluid passing through the pipes is water and its kinematic viscosity is 1.02x10-6 m2 / s. Other data are given in the table below. please help me fast pleaseeee
A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.81 cm and the other end is 0.28 cm. The larger and smaller ends are located 10 m and 4 m, respectively, from the datum line. If the flow at the 10 m datum line is 1.60 m/s and the pressure is 5244 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.