The floor framing plan of a reinforced concrete structure is shown in the figure. The beams are 280mm wide and 520mm deep and the slab is 110mm thick. Other than concrete weight, the floor is subjected to an additional (superimposed) dead load of 3 kPa and live load of 5.2 kPa. Unit weight of concrete is 23.5 kN/m3. (U = 1.2D + 1.6L) Due to space considerations, the columns at E and H are to be removed. This will make girder BEHK support beams DEF at E and GHI at H. • Determine the uniform service dead load on beam DEF in kN.m. [Select] Determine the uniform service live load on beam DEF in kN/m. [Select ] • Determine the factored concentrated load at E due to loads on beam DEF in kN. [ Select ] A B. 2-5 E 25 6.2 2.5m <>

The floor framing plan of a reinforced concrete structure is shown in the figure. The beams are 280mm wide and 520mm deep and the slab is 110mm thick. Other than concrete weight, the floor is subjected to an additional (superimposed) dead load of 3 kPa and live load of 5.2 kPa. Unit weight of concrete is 23.5 kN/m3. (U = 1.2D + 1.6L) Due to space considerations, the columns at E and H are to be removed. This will make girder BEHK support beams DEF at E and GHI at H. • Determine the uniform service dead load on beam DEF in kN.m. [Select] Determine the uniform service live load on beam DEF in kN/m. [Select ] • Determine the factored concentrated load at E due to loads on beam DEF in kN. [ Select ] A B. 2-5 E 25 6.2 2.5m <>

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steel beams (A = 9,100 mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown in Figure. Determine the dead loads acting on beam BF and girder AD
shows the floor framing plan of a reinforced concrete building. All beams are 300 mm x 600 mm. The properties are as follows: slab thickness = 100 mm; super imposed dead load = 3 kPa; live load = 4.8 kPa; concrete unit weight = 24 kN/m3. The columns at E and H are deleted thus girder BEHK alone supports beam DEF at E and beam GHI at H. Calculate the total ultimate load in kN concentrated at E induced by beam DEF using tributary area method.
The floor system of an apartment building consists of 100mm thick reinforced concrete slab (unit weight = 23.6 KN/m^3) resting on three steel floor beams 3.0 meters on centers. Calculate the total dead load in KN/m due to slab for a single floor beam. Assume one-way slab.
The floor system of an apartment building consists of a 4-inch-thick reinforced concrete slab resting on three steel floor beams, which are in turn supported by two steel girders, as shown below. The areas of cross section of the floor beams and the girders are 18.3 in.2 and 32.7 in.2, respectively. Determine the live load acting on beam CD.
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of the whole structure which is 77 lbs per ft. FN= 87 OR 87X10 = 870
The floor system of an apartment building consists of a 4-inch-thick reinforced concrete slab resting on three steel floor beams, which are in turn supported by two steel girders, as shown below. The areas of cross section of the floor beams and the girders are 18.3 in.2 and 32.7 in.2, respectively. Determine the dead load acting on the beam CD.
PROBLEM 1: The homogeneous structure shown weighs 21.45 kN per square meter of cross-section. The structure is subject to horizontal uniformly distributed load P1 and triangularly distributed load P2 perpendicular to side AB. Given: H1 = 9 m; H2 = 6 m; H3 = 12 m X1 = 6 m; X2 = 5 m P1 = 220 kN/m; P2 = 280 kN/m 4 Magnitude of resultant, R 4314.04 5 Angle of resultant direction from x-axis, θx 86.01 6 Distance of resultant from C measured along line CD, X 9.116
a simply supported beam is carrying a varying load and a uniform load as shown in the figure. If the beam properties are given below, what is the final stress at bottom of beam section at a distance 2.47m from the right support where the totall losses of the prestressing force is 24% mpa beam wid=217mm height= 480mm varying load= 9.67kn/m uniform load = 4.27 kn/m x = 3.32 y = 5.95 Prestressing force = 429kn eccentricity = 95mm
In the trapezoidal load shown, if h1 = 4 kN/m, and y = 3 kN/m. What is the value of h2?
The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steel beams (A=9,100 mm2) that, in turn, are supported by two steel girders (A=25,600 mm2), as shown below. Determine the live load acting on the beam BF.
A prefabricated structure is used to construct a bus stop. Several forces are applied to this rigid body as shown in the cross section in the Figure below. The acting loads on the cross section are represented by three concentric forces F⃗1 = 60 kN at I, F⃗2 = 10 kN at G, and F⃗3 = 40 kN at Q, and a couple M⃗1 = 250 kNm (clockwise) at H. The distributed load effects from the snow are vertical acting between points N and P on the canopy, and points D and C on the lower slab. The distributed load between N and P increases linearly from 0 to a magnitude equal to w1 = 15 kN/m, while the distributed load from D to C starts with a magnitude w2 = 18 kN/m and decreases linearly to w3 = 10 at G due to the wind effect. The angle α of force F⃗1 with the horizontal line is 25o. F⃗2 is vertical, while F⃗3 is horizontal. Do the following: 1. Find the reduced force-couple system at point E.2. Substitute the force-couple system with a single force system R and its position from E. 3. Sketch R with…
A regular block of concrete serving as foundation post to a structure has a cross-section of 900 sq.cm and weighs 1000 Pascal per meter. If the overall height of the block is 100cm, compute the total weight of the block in kN