The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steel beams (A=9,100 mm²) that, in turn, are supported by two steel girders (A=25,600 mm²), as shown below. Determine the live load acting on the beam BF. Steel floor beam (A-9,100 mm²) 10 m B O a. 23.95 kN/m Ob. 9.60 kN/m O c. 14.35 kN/m O d. 30.00 kN/m -Steel girder (A-25,600 mm²) D C F G -3 at 5 m- 15 m F Steel column 130 mm concrete slab

The floor system of a gymnasium consists of a 130-mm-thick concrete slab resting on four steel beams (A=9,100 mm²) that, in turn, are supported by two steel girders (A=25,600 mm²), as shown below. Determine the live load acting on the beam BF. Steel floor beam (A-9,100 mm²) 10 m B O a. 23.95 kN/m Ob. 9.60 kN/m O c. 14.35 kN/m O d. 30.00 kN/m -Steel girder (A-25,600 mm²) D C F G -3 at 5 m- 15 m F Steel column 130 mm concrete slab

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 3-cm-diameter horizontal pipe attached to a surface makes a 90° turn to a vertical upward direction before the water is discharged at a velocity of 6 m/s. The horizontal section is 5 m long and the vertical section is 4 m long. Neglecting the mass of the pipe and considering the weight of the water contained in the pipe, the bending moment acting on the base of the pipe on the wall is (a) 11.9 N·m (b) 46.7 N·m (c) 127 N·m (d) 104 N·m (e) 74.8 N·m
Determine the vertical distance of the center of gravity of the curved gate from the water surface shown in the figure. The curved gate is 5.7 m long. The values of the vertical component (Fv) and the resultant force. (F) acting on the gate are 300 kN and 400 kN asap
An open horizontal tank 3 m high, 3.6 m wide and 5.1 m long is initially filled at 2 m of water. A. Determine the required acceleration in m/s2 so that no water will be spilled? B. Determine the required acceleration in m/s2 so that 1/3 of the initial volume of water will be spilled C. Determine the remaining volume in cu.m if it accelerated at 7 m/s^2D. Determine the minimum hydrostatic force in kN at the side of the tank if 2/3 of the initial volume will be spilled E. Determine the maximum hydrostatic force in kN at the side of the tank if it accelerates at 3 m/s^2
Determine the smallest force P that must be applied in order to cause the 150-lb uniform crate to move. The coefficent of static friction between the crate and the floor is μs = 0.5
Please explain with the diagrams A cantilever beam of clear span 2 m is built into a wall of 30 cm thickness. The beam carries a concentrated load of 1 KN at the free end. Assume that the pressure exerted by the wall on the beam is linearly varying along the 30 cm thickness of the wall into which the beam is embedded. Find the pressure distribution exerted by the wall on the beam.
where, bf1= 260 bf2 = 120 tf = 25 tw = 16 d1 = 160 d2 = 110 1. Calculate the location of the neutral axis from the bottom of the beam in mm. 2. Compute for the moment of inertia in 1x10^6 mm^4. 3. What is the value of in kN/m, considering flexural stress in tension? 4. What is the value of in kN/m, considering flexural stress in compression? 5. What is the statical moment of area (Q) in 1x10^3 mm^3 ? Use three decimal places. 6. What is the value of in kN/m, considering shear stress at the welded section? 7. What is the safest value of in kN/m? Use three decimal places.
For the reservoir at the top of the figure: a) Determine the width of a wall on the chamfer (diagonal face) at the left end that can safely support the water in the reservoir at the elevation shown if the wall material can support 2500 pounds per square foot. Also, determine the diagonal distance from the lower end of the chamfer to the resultant force. b) Determine whether a hollow concrete block with outside dimensions of 2’ X 3’ X 5’ weighing 2000 pounds will float in the reservoir and, if so, how much of the block will remain above the water surface. (Consider the likely orientation of the block in the water.) solve using the bournellis equations and can you please show the formulas and solving it thank you
1. A vessel is filled with oil (ρoil = 900 kg/m^3) up to 1 m of its height. It is 3m wide, 2m high and 10 m long. Find the following : A. The maximum horizontal acceleration that can be charged to the vessel without spilling anyoil. B. If this vessel is closed and is completely filled with oil and accelerated horizontally at a rate of 3 m /s^2 B.1. The total force acting at the rear wall and at the front wall of the vessel. B.2. The accelerating force on the fluid mass.
Problem 3) Consider the Figure 3 – C, an overhanging beam carries two uniformly distributed loads12 kN/m and 6 kN/m and a concentrated load Pc = 2.5 kN. Determine the following:a) The moment of inertia about the neutral axis
Question: Calculate the vertical reaction force at G and the vertical reaction force at A.
PROBLEM 1: The homogeneous structure shown weighs 21.45 kN per square meter of cross-section. The structure is subject to horizontal uniformly distributed load P1 and triangularly distributed load P2 perpendicular to side AB. Given: H1 = 9 m; H2 = 6 m; H3 = 12 m X1 = 6 m; X2 = 5 m P1 = 220 kN/m; P2 = 280 kN/m Required Answer Equivalent force of uniform load P1 1980.00 Total weight of the structure, W 3603.60 Horizontal component of the resultant, Rx 300.00
An open tank 3m by 3m in horizontal section weighs 4 kN and contains water to a depth of 1m. It is acted by an unbalanced force of 18 kN parallel to the pair of sides. a) Determine the acceleration of the tank. b) What must be the height of the tank so that no water will spill out? c) If the acceleration is increase by 4m/s2 , how much water will spill out?