The floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5 kPa and a uniformly distributed live load of 1.9 kPa over its surface area. Determine the factored (ASD) axial load (kN) to be carried by the column at C. Girder Floor beam Column A B H TH -IK H L G C H M 4 at 7.5 m = 30 m D N E -To 2 at 12 m = 24 m

The floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5 kPa and a uniformly distributed live load of 1.9 kPa over its surface area. Determine the factored (ASD) axial load (kN) to be carried by the column at C. Girder Floor beam Column A B H TH -IK H L G C H M 4 at 7.5 m = 30 m D N E -To 2 at 12 m = 24 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow rectangular column carries three axial loads as shown in Fig. 4. If P1=100kN, P2=200kN, and P3=300kN respectively, determine:(a) the magnitude and position of the resultant load with reference to X-X and Y-Y axes;(b) the combined stresses at each of the corners a, b, c and d.
A structural framing plan for the upper floors in a building is shown in the figure below. A site-cast concrete slab-and-beam system is used. The floor framing system consists of a series of parallel beams at 2.8-meter centers that support a continuous one-way spanning slab (adjacent columns are spaced by a distance of 8.4-meter in both horizontal and vertical directions). The uniformly ultimate (factored) distributed load for the one-way slab is equal to 14 kN/m2. Ignore the own weights of beams and walls. Compute the value of load on column H. Compute the value of distributed load on beam EF. Compute the value of each of concentrated loads on beam HK. Compute the value of maximum moment for beam HK.
A two story office building has interior column spaced at 6.7m apart in two perpendicular directions. If the flat of the roof live loading is allowed to be reduced live load of an interior column located at the ground floor level. Using NSCP 2010, determine the following: a.) basic roof live load in kPa b.) roof live load in kN forthe column c.) basic floor live load due to occupancy in kPa d.) reduced floor live load in kN for the column e.) total live load supported by the ground floor column
The partial plan layout for the framed structure of a multistory building is shown below. The vertical structure consists of columns and the horizontal floor structure of a one-way deck and beam system. The uniformly ultimate (factored) distributed load for the one-way-spanning deck is equal to 0.14 kip/ft2. Ignore the own weights of beams and walls. L1 = 22 ft, L2 = 22 ft, L3 = 32 ft. Compute the load on column 1. Compute the value of distributed load on beam A. Compute the value of concentrated loads on beam C. Draw the shear and bending moment diagrams for beam C (with values) – Assume beam C as simply supported.
1. Determine the critical bucklng stress of the column in MPa. a.120.68 b.116.10 c.101.32 d.108.57 2. Determine the nominal axial load that the column can carry in kN/ a.1448.16 b.1393.20 c.1221.84 d.1302.84 3. Determine the service live load that can be applied in the column kN. a.119.53 b.597.64 c.143.44 d.956.22 Answer:101.82, 1221.84,597.64
The simple beam carries a concentrated load P = 15kN. Dimension a and b are 2.5m and 1.2m. respectively. What is the required section modulus of the beam, in mm^3, if the stress is 120Mpa?
A beam having a span of 4m is subjected to a maximum shear of 20 kN. It has a triangular cross - section having a base width of 140 mm and an altitude of 300 mm. Which of the following gives the maximum shearing stress developed on the beam? a. 1.43 MPa b. 1.80 MPa c. 1.62 MPa d. 1.78 MPa
A triangular wooden beam width 150 mm base and 300 mm height carries two concentrated load of 20 kN at third points. If the simple span of the beam is 6 m, 1. Compute the maximum shearing stress of the beam. a. 0.58 MPa b. 1.33 MPa c. 0.48 MPa d. 0.86 MPa 2. Compute the bending stress of the beam. a. 56.33 MPa b. 71.11 MPa c. 78.48 MPa d. 45.78 MPa
The wide flange beam shown supports the concentrated load ? and a total uniformly distributed load of 2?. Determine the maximum safe value of ?i f flexural stress ?? ≤ 10 ??? in tension, ?? ≤ 20 ??? in compression and shear stress ? ≤ 1.4 ???.
A triangular wooden beam width 150 mm base and 300 mm height carries two concentrated load of 20 kN at third points. If the simple span of the beam is 6 m. Compute the maximum shearing stress of the beam. a. 0.58 MPa b. 1.33 MPa c. 0.48 MPa d. 0.86 MPa
shows the floor framing plan of a reinforced concrete building. All beams are 300 mm x 600 mm. The properties are as follows: slab thickness = 100 mm; super imposed dead load = 3 kPa; live load = 4.8 kPa; concrete unit weight = 24 kN/m3. The columns at E and H are deleted thus girder BEHK alone supports beam DEF at E and beam GHI at H. Calculate the total ultimate load in kN concentrated at E induced by beam DEF using tributary area method.
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam