Find the correct option of the given question briefly In a Lagrangian system, the position of a fluid particle in a flow is described as x = x,eand y = Y,e where t is the time while Xar Yor and k are constants. The flow isA. unsteady and one-dimensionalB. steady and two-dimensionalC. steady and one-dimensionalD. unsteady and two-dimensional

Given; The position of fluid particle in a flow is described as; →x=x0e-ktand…

Answered: The flow is

Engineering

Mechanical Engineering

The flow is

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.3P: Evaluate the Nusselt number for flow over a sphere for the following conditions: D=0.15m,k=0.2W/mK,...

See similar textbooks

Related questions

Q: Fluid of specific gravity 0.80 flows in a 230 mm diameter pipe. Find the critical velocity in m/s.…

A: Given information, S=0.8, D=0.23m Viscosity Find, Critical velocity

Q: As water is flowing from a water tower to someone house, water is flowing at a speed of 3 m/s in a…

A: Water velocity at 0.3 m diameter, V1=3 m/s Gradual increase in diameter, d2=1.8m Gradual decrease in…

Q: The pressure is the highest pressure possible in the flow, if elevation changes are neglected.…

A: The stagnation or total pressure is the pressure measured at the point where the liquid comes to…

Q: What would you have to do to reduce this flow angle to zero degrees?

A: Here the reducing flow by zero degree angle attack

Q: flowing through a diameter and the of the pipe is incr the

A: given:d2=1.5d1

Q: Completely solve and box the final answers. Use 4 decimals at all instances. Pure ethyl alcohol at…

Q: e end of the pipe. If the number, the mass flow

Q: The flow is

A: Given: In a langrangian system is defined in which individual fluid paticlesare tracked.The…

Q: gle-acting ai volume flow a. The free

A: given:T1=180Cn=1.26N=600rpmP2=668KPaP1=101.3Kpa

Q: A hydro-electric dam uses turbines to generate electricity as reservoir over the turbine blades. A…

A: (a) To fill: The blanks of the statement with appropriate choice. Explanation: Hydroelectric dam: A…

Q: 11" D calcresource.com 8" 4 3 4

A: following is the solution

Q: Dynamic

A: ωAB=12 rad/svB=ABωAB=12*.2=2.4 m/sVB=vB→;VD=vD↑ Instantaneous center of bar BD lies at C…

Q: Solution Derivation of volumetric flowrate dimension

A: Flow rate: the amount of fluid flowing through a particular crosssection per unit time is known as…

Q: -< 5 the surface roughness. Hydraulically smooth condition the flow. Why is the limit set to et < 5?

Q: operat = 0, dx ду dz + = 0, dx ду dz The above steps are legal only if the flow is, Answers:…

A: Incompressible flow is defined as a flow in which the density of any fluid,remains constant. A…

Q: -is the change

A: Option (c) 300J is correct option

Q: velocity

A: vb=ω2AB with known velocity draw velocity diagram from velocity diagram we get vb=vc it is same for…

Q: flow is alsc tational flov ous flow the followi of oil in m erground fl-

A: Hi and thank you for the questions. Since you have asked multiple questions, we will solve the first…

Q: The first plane is D-8 double bubble and the second plane is Blended wing body. Based on what you…

A: Given pictures indicate the coefficient of pressure of two aircraft designs 1. D-8 Double bubble…

Q: Calculate the flow in the siphon, assuming flow is fully-rough turbulent.

Q: If the inlet Mach number is 15 and the outlet Mach number is 1.2, then the area is convergent Select…

A: The given statement " If the inlet Mach number is 1.5 and the outlet Mach number is 1.2, then the…

Q: In shut off valve experiment, the 3/6th of valve position, the discharge is found as of 7 lit/s for…

Q: In shut off valve experiment, the 3/ 6th of valve position, the discharge is found as of 6 lit/s for…

Q: A pipe bends through 900 from its initial direction as shown in fig.13. The pipe reduces in diameter…

A: The flow in pipe will have to follow continuity equation: A1V1 = A2V2 The flow must also follow…

Q: A syringe (X), forces air, at a high velocity, over a straw (Y). The air in the water chamber (Z) is…

A: Solution is attached below

Q: Fluid flows through the pipe into a rigid tank in the shape of a cube. During that process, heat is…

Q: Fill in the blank which is given below The linear displacement can be also calculated with using the…

A: We know that

Q: The energy loss due to the change of flowrate of a fluid flow in direction is known as minor loss.…

A: The energy loss due to friction is known as major loss and due to bend and other cross sectional…

Q: The velocity

A: Given; tBlock is acted upon by a horizontal force; P=10twhere t=denotes the time in seconds.A block…

Q: Briefly explain the definition of potential flow.

A: 1. Potential flow is briefly explained. 2. Mathematical expression is provided.

Q: : Solve two of the following: A: State the types of flow of fluid, and write the equation of each…

A: To state the type of fluid flows Note:As per our guidelines we are supposed to answer only one…

Q: Fluid flows through the pipe out of a rigid tank in the shape of a cube. During that process, heat…

Q: n the table given below. -Excel and determine the fluid types. (Show your o you use to describe the…

A: Given data velocity gradient and shear stress are given Required Graph between gradient and shear…

Q: The product of the cross sectional area of the cylinder and its velocity is used to determine the…

A: Flow rate is the measure of the volume of liquid that moves in a certain amount of time.

Q: Which of the following statements is true? (There are multiple answers I think) a. In the energy…

Q: 27. During the passage through the open system, the following data were gathered:

Q: 16.2 What must be the velocity of flow of water from a 2-in diameter nozzle to exert a force of 300…

A: The calculated velocity of flow of water from a 2- in diameter nozzle.

Q: 1. The length of a pipe is 168 meters. If the pressure drop is 50 kPa for every 30 meters. What is…

A: GIVEN DATA - 1. PRESSURE DROP FOR 30m IS 50KPa 2. DIA.=4in , VELOCITY V=11ft/s

Q: Jaymar bought a small water pump for his aquarium. The pump delivers 0.2 L/s at a net head of 2 m…

A: Given:- For old pump : Discharge (Q) = 0.2 L/s Head (H) = 2 m Speed (N) = 1041 rpm For new pump :…

Q: The rate of flow of water through a horizontal pipe is 200+last two digits of your id lit/s. The…

A: according to the given details provided.

Q: flow. What is the pressure drop in the pipe "in Pascals"? Select one: A. 4.98

A: Fluid Mechanics: It is a branch of physics in which concerns with mechanics of fluids & forces…

Q: •17.10 What is the reliat .99 .99

A: It is required to determine reliability of system

Q: A three stage pump delivers 1.89 m3/s against a head of 200 m with a speed of 2000 rpm. Find the…

Q: What would you have to do to reduce this flow angle to zero degrees?

A: reduce the flow angle to zero degree ***As per comment i had given the answer only sub question****

Q: orm of governing equations are solved at the grid points to find the unknown fluid quantitie

A: Grid generation in CFD is a collection of techniques for defining a numerical mesh throughout the…

Q: what is the correct statement for the total energy by flowing fluid equation choose three answers

A: Solution:

Q: what is the velocity V

A: Given ; A bullet of mass m travels at a very high velocity V and gets embededinside the block of…

Q: Select the word: uniform, one-dimensional, two-dimensional, or three-dimensional, that best…

A: Kindly refer the Solution below.

Q: Briefly describe the definition of potential flow.

Concept explainers

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.

Question

Find the correct option of the given question briefly

In a Lagrangian system, the position of a fluid particle in a flow is described as x = x,e
and y = Y,e where t is the time while Xar Yor and k are constants. The flow is
A. unsteady and one-dimensional
B. steady and two-dimensional
C. steady and one-dimensional
D. unsteady and two-dimensional

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For a flow in the xy plane, the x component of the velocity is given as u=3x2y-y3. Determine the y component for steady state and incompressible flow. Does this result also apply to unstable, incompressible flow? Why is that? How many possible y components are there? Discuss.
In a stream line steady flow, two points A and B on a stream line are 1 m apart and the flow velocity varies uniformly from 2 m/s to 5 m/s/ What is the acceleration of fluid B?
for a steady incompresible two dimensional flow, represented in cartesian coordinates (x,y), a student correctly writes the equation of pathline of any arbitrary particle as dx/dt =ax and dy/dt= by where a and b are constants having unit of second‐¹. if value of a is 5 determine the value if b.
for a steady incomprssible two dimensional flow, represented in cartesian coordinates (x,y), a student correctly writes the equation of pathline of any arbitrary particle as dx/dt =ax and dy/dt= by where a and b are constants having unit of second‐¹. if value of a is 5 determine the value if b.
Q1 Fluid Mechanics - Buckingham π Theorem Develop a step-by-step organization chart/schema/mind map of Buckingham π Theorem and apply it to a generic fluid mechanics problem of your choice, with the exception of the load loss problem in forced flows.
A flow is uniform if the parameters describing the flow vary with distance along the flow path. TRUE FALSE
The velocity field of a flow is described by V-›= (4x) i-›+ (5y + 3) j-›+ (3t2)k-›. What is the pathline of a particle at a location (1 m, 2 m, 4 m) at time t = 1 s?
In two dimensions along the converging nozzle, stable, considering incompressible flow. The velocity on the horizontal centerline (x-axis) is given as V=V1(1+x/L)i Derive an equation for the acceleration of a particle moving along the centerline using (a) Euler's approximation and (b) Lagrangian approximation. Discuss the acceleration for the particle being at the beginning and end of the channel.
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3 Please.. explain more easy
6 For incompressible flow, density remains the same Select one: True False
A flow is non-uniform when the magnitude of the parameters varies from point to point along the flow path. TRUE FALSE