Help me. Geotech . The flow net around a sheet pile wall is shown in the sketch. Theproperties of the soil are: permeability coefficient = 0.09 m/day(isotropic), specific gravity = 2.70 and void ratiopile wall and the bottom of the soil are impermeable.%3D0.85. The sheet10m1.5m3mThe seepage loss (in m3 per day per unit length of the wall) ofwater is(A) 0.33 (B) 0.38 (C) 0.43 (D) 0.54

Answered: Image /qna-images/answer/c8da1cb2-065e-450b-a5e0-192d08d77300.jpg

The flow net around a sheet pile wall is shown in the sketch. The properties of the soil are: permeability coefficient (isotropic), specific gravity = 2.70 and void ratio = 0.85. The sheet pile wall and the bottom of the soil are impermeable. 0.09 m/day %3| 10m 1.5m 3m The seepage loss (in m3 per day per unit length of the wall) of water is (A) 0.33 (B) 0.38 (C) 0.43 (D) 0.54

The flow net around a sheet pile wall is shown in the sketch. The properties of the soil are: permeability coefficient (isotropic), specific gravity = 2.70 and void ratio = 0.85. The sheet pile wall and the bottom of the soil are impermeable. 0.09 m/day %3| 10m 1.5m 3m The seepage loss (in m3 per day per unit length of the wall) of water is (A) 0.33 (B) 0.38 (C) 0.43 (D) 0.54

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.7CTP

See similar textbooks

Similar questions

The Figure below shows a long pile wall driven in sand with Coefficient of permeability K= 0.05cm/sec.it is required to: 1.Estimate the max. possible value of dimension h, where Ah=1.2. 2.Calculate the seepage loss (m /day) per meter of wall
For a given flow net around a sheet pile wall, determine the following How high will the water be in piezometers located at point a, b, c and d, Rate of seepage through flow channel II, Total rate of seepage The soil permeability is 5 x 10-3 cm/sec .
Draw a flow net for a single row of sheet piles driven into a permeable layer as showin Figure Q3 (b) below. Thus, determine the seepage loss per meter length of thesheet pile.H1 = 9.6 m D = 5 mH2 = 3.7 m D1 = 13 m
A flow net for flow around a single row of sheet piles in a permeable soil layer is shown in Figure below with a scale as shown. Given that kx = kz=k = 4 x 10-3 cm/sec, determine How high (above the ground surface) the water will rise if piezometers are placed at points a and b The total rate of seepage through the permeable layer per unit length The approximate average hydraulic gradient at c factor of safety against piping x=1.6 y=2.8
Refer to Figure 9.42b. Let L = 18 m, γfill = 17 kN/m3, γsat(clay) = 19.8 kN/m3, Φ'clay = 20°, Hf = 3.5 m, and D (pile diameter) = 406 mm. The water table coincides with the top of the clay layer. Determine the total downward drag force on the pile. Assume ẟ' = 0.6 Φ'clay.
A sheet pile wall is driven to a depth of 6 m into a permeable sand layer (k = 6X10-3 mm/s) of 13.5 m thickness lying on an impermeable layer. The water on one side of the wall is at a height of 4.5 m, while on the other side, pumps maintain the water level at ground level. Estimate the number of flow lines
The sheet pile is driven in the Cebu South reclamation area and the area to one side is pumped down as shown in the flow net. The permeability of the sand is 0.001 m/s. below the elevation of 20 m us an impermeable rock layer. Determine the flow per unit length.How high (above the ground surface) the water will rise if a piezometer will be placed at A?
Problem #1 The figure below shows a cantilever sheet-pile wall penetrating a granular soil. Here, L1 = 4 m, L2 = 8 m, unit weight above water table= 16.1 kN/m3, saturated unit weight = 5 18.2 kN/m3, and friction angle of sand = 32 degrees. a. What is the theoretical depth of embedment, D? b. For a 30% increase in D, what should be the total length of the sheet piles? c. Determine the theoretical maximum moment of the sheet pile. d. If the allowable flexural stress = 170 MPa, compute the required section modulus of the sheet pile.
Redo Problem 14.1 with the following: L1 = 3m, L2 = 6 m, γ = 17.3 kN/m3, γsat = 19.4 kN/m3, and ϕ′ = 30°. 14.1 Figure P14.1 shows a cantilever sheet-pile wall penetrating a granular soil. Here, L1 = 4 m, L2 = 8 m, γ = 16.1 kN/m3, γsat = 18.2 kN/m3, and ϕ′ = 32°. What is the theoretical depth of embedment, D? For a 30% increase in D, what should be the total length of the sheet piles? Determine the theoretical maximum moment of the sheet pile.
Refer to Figure 18.26b. Let L = 15.24 m, fill = 17.29 kN/m3, sat(clay) = 19.49 kN/m3, clay = 20, Hf = 3.05 m, and D = 0.406 m. The water table coincides with the top of the clay layer. Determine the total downward drag on the pile. Assume that = 0.6 clay. FIG. 18.26 Negative skin friction
Refer to Figure 18.9. A cantilever sheet pile is driven into a granular soil where the water table is 2 m (L1) below the top of the sand. The properties of the sand are =40, =17.5kN/m3, and sat=19kN/m3. It is proposed to excavate to a depth of 6 m (L) below the ground level. Determine the actual depth to which the sheet pile must be driven (L + D), using the net lateral pressure diagram. Note: Dactual=1.3(L3+L4)theory
Determine the factor of safety against heave on the downstream side of the single-row sheet pile structure shown in Figure 9.30. Use the following soil and design parameters: H1 = 7 m, H2 = 3 m, thickness of permeable layer (T) = 12 m, design depth of penetration of sheet pile (D) = 4.5 m, and γsat = 17 kN/m3