The following are steel design concepts. 1. A member is selected that has cross-sectional properties such that allowable values are not exceeded 2. ØRn. 3. Working loads are also known as service loads. 4. Collapse mechanism. 5. Factored loads are loads that bring the structure or member to its limits. Which of the following is correct? 1,2 and 3 are allowable stress design concepts. O 2,4 and 5 are LRFD concepts. O There are no plastic design concepts listed. 3,4 and 5 are limit states design concepts.

The following are steel design concepts. 1. A member is selected that has cross-sectional properties such that allowable values are not exceeded 2. ØRn. 3. Working loads are also known as service loads. 4. Collapse mechanism. 5. Factored loads are loads that bring the structure or member to its limits. Which of the following is correct? 1,2 and 3 are allowable stress design concepts. O 2,4 and 5 are LRFD concepts. O There are no plastic design concepts listed. 3,4 and 5 are limit states design concepts.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported concrete beam 6m long is reinforce with four-28 mm diamgram tension bars. The beam has a width of 300mm and over all depth of 400.the steel covering to the centroid of the renforcement is 70 mm fc=30mpa and fy 418mpa A .draw a stress diagram B.compute for the ultimate capacity of the beam
A timber beam having a simple span of 5m carries a total load, including its weight, of 15 kN/m. It has a width of 200mm and a depth of 300mm for its nominal dimensions and its dressed dimensions have 10-mm deductions for the width and height dimensions. The wooden section is made of 80% stress grade Apitong (such that Fb = 16.5 MPa, Fv = 1.73 MPa, and E = 7310 MPa). (a) Determine the maximum flexural stress of the beam (fb). Check if it is adequate for bending by comparing fb to Fb. (b) Determine the maximum shearing stress (fv). Check if it is adequate for shearing by comparing fv to Fv. (c) Determine the maximum deflection (δmaximum). Check if it is adequate for deflection by comparing δmaximum to δallowable of 1/300 of the span.
A hollow circular pole, 6m. thick with 300 mm outside diameter and height of 3 m weighs 150 N/m. The pole is subjected to the following vertical load P= 3KN at an eccentricity e=100mm from the centroid of the section, lateral force H = 0.45 KN at the top of the pole. Note, used combined stresses principle for solving the ff. questions. A. Determine the maximum compressive stress at the base due to the loads. B. If the hollow pole is replaced by a solid wood pole of 250 mm diameter, determine the maximum shear stress. C. Determine the maximum tensile stress at the base due to the loads.
Topic: Singly Reinforced Concrete A simply supported concrete beam 6m long is reinforced with four-28mm diam. tension barss. The beam has a width of 300mm and overall depth of 400m. The steel covering to the centroid of the reinforcements is 70mm, fc’= 30 MPa and fy= 418 MPa. A. Draw the stress diagram. B. Compute for the Ultimate capacity of the beam Note: Don’t conclude compression bars.
Three steel plates, each 16 mm thick and width of 300 mm are joined by two 20-mm diameter rivets as shown. Assume the rivet hole diameter = 23mm. If the load P = 50 kN, determine the largest bearing stress acting on the rivets. Show all necessary solution.
A simply supported beam 6.5m long, 350mmx500mm, prestressed with a straight tendon located 150mm below the neutral axis with effective prestressing force, Pe, of 300kN. Total load carried by the beam is 20kN/m. D. Determine the compressive stress caused by the tendon alone if Pe is 150mm below the neutral axis, MPa.E. Determine the final compressive stress, MPa.F. Determine the final tensile stress, MPa.
A bridge girder AB on a simple span of length L = 20 m supports a distributed load of maximum intensity q at midspan and minimum intensity q/2 at supports A and B that includes the weight of the girder (see figure). The girder is constructed of three plates welded to form the cross section shown. (a) Determine the maximum permissible load q based upon an allowable bending stress sigma = 140 MPa. Round to the nearest tenth. qmax = ___ kN/m (b) Determine the maximum permissible load q based upon an allowable shear stress Tau = 60 MPa. Round to the nearest tenth. qmax = ___ kN/m
1. Differentiate the permanent and the variable action with suitable examples 2. Analyze the stress-strain relationship of steel. Notes : Internal forces Fcc = 0.567fck(b x 0.8x) = 0.454 fck bx Fst = 0.87 fyk As Moment of resistance with respect to steel, M = Fcc.z Moment of resistance with respect to concrete, M = Fst.z Mbal = Kbal fck bd2 where Kbal = 0.167 As ‘ = (M-Mbal) / 0.87 fyk (d-d’) As = Mbal / 0.87 fyk zbal + As’
Design the slab reinforcement if the maximum positive moment is Mup=wul2/11. and the maximum negative moment is Mun=wul2/10. Include the strain in you solution. Given: Superimposed dead load = 4.76 kPa Live Load = 1.9 kPa Weight of slab = 3.45 kPa Thickness = 150 mm Length = 10.9m Span = 3m
An S 380 x 74 section is used as a simply supported beam to carry the uniformly distributed load of magnitude 3W and the concentrated load W. What is the maximum allowable value of W if the working stress in bending is 120 MPa?
The W610 x 82 beam shown above has a Young’s modulus of ? = 200 GPa, an allowable bending stress of ?????? = 300 MPa and an allowable shear stress of ?????? = 150 MPa.a) Draw the SFD and BMD of the beam and indicate ???? and ????.b) Determine if the beam is sufficiently strong to support the applied loads.c) Assuming that the beam is sufficient, what is the vertical deflection and slope at the free end?
A reinforced concrete beam has a width of 300 mm and an effective depth of 618 mm. Compressive reinforcement (if required) will be placed at d' = 60 mm. fc' = 28 MPa and fy = 415 MPa. Use 2010 NSCP. The beam is to support a factored bending moment of 600 kN.m. use phi = 0.90 for flexure. Questions 1.1) Calculate the steel ratio for balanced section, (rho bal) 1.2)Determine the theoretical steel ratio required (rho) for the beam to support the given factored moment. * 1.3)Following NSCP requirements, determine the required area for steel reinforcement, As * 1.4)Determine the number of 28 mm diameter bars required as tension reinforcement. *