1. The following circuit shows a discrete common source MOSFET ampliierThe MOSFTE is n-channel MOSFET,The transconductance of the n-channel MOSFET (g) is 3 mA/V.Ri 100 kN, RGI = 47 MQ, Ri 100 kQ, Ra210 MO, Rs =2 k2, Ro – 4,7 k2,RL 10 k2, Rig 100 k2, Cgs-1 pF, Cgd -0.2 pF, VAThe C-S MOSFET amplifier has three low break frequencies in low frequency band atfLI 1 Hz (caused by Cei), fiz 100 Hz (caused by Cs), fio= 10HZ (caused by Cc)(d) Draw small signal equivalent circuit of the amplifier in high frequency band.(e) Derive the transfer function, TH(s), and find the high corner frequency from thetransfer function. (You may use Miller's theorem, but not time constants)VDDRG1RDCc2Q1Cc1RLRsigRG2CsVsigRS

The following circuit shows a discrete common source M The MOSFTE is n-channel MOSFET. The transconductance of the n-channel MOSFET (g) is 3 mA/V. Rsig 100 k2, RGI = 47 MO, Raig 100 k, Ro210 M2, Rs =2 k2, Ro-47 kS2, RL 10 k2, Rig 100 k2, Cs-1 pF, Ced 0.2 pF, VA ne C-S MOSFET amplifier has three low break frequencies in low frequency band at fLI-1 Hz (caused by Cei), fi2 -100 Hz (caused by Cs), fio= 10HZ (caused by Ccz) (d) Draw small signal equivalent circuit of the amplifier in high frequency band. (e) Derive the transfer function, TH(s), and find the high corner frequency from the transfer function. (You may use Miller's theorem, but not tìme constants).

The following circuit shows a discrete common source M The MOSFTE is n-channel MOSFET. The transconductance of the n-channel MOSFET (g) is 3 mA/V. Rsig 100 k2, RGI = 47 MO, Raig 100 k, Ro210 M2, Rs =2 k2, Ro-47 kS2, RL 10 k2, Rig 100 k2, Cs-1 pF, Ced 0.2 pF, VA ne C-S MOSFET amplifier has three low break frequencies in low frequency band at fLI-1 Hz (caused by Cei), fi2 -100 Hz (caused by Cs), fio= 10HZ (caused by Ccz) (d) Draw small signal equivalent circuit of the amplifier in high frequency band. (e) Derive the transfer function, TH(s), and find the high corner frequency from the transfer function. (You may use Miller's theorem, but not tìme constants).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A common emitter amplifier as shown in Figure Q2 has the following parameters, β = 100, R1= 33K, R2 = 10K, RC = 3K3, RE = 1K, ro =  and VBE = 0.7 V.State all assumptions made.i. Check whether βRE>>10R2 is satisfiedii. Use the appropriate approach of analysis to determine the Quiescent point; IBQ,ICQ and VCEQ.iii. Draw the small signal equivalent circuit. Determine input impedance, Zin, outputimpedance, Zout, and the voltage gain, AV, if RL=20kΩ.
Please analyze the circuit and determine the voltage gain of both (Av,dc = Vc/Vb for DC analysis) and (Av,ac = Vo/Vs for AC analysis) where RB = 450K, Rs = 80, Ci = 47 uF, RC = 3.3K, Co = 4.7 uF, RL = 100K. In addition, find the output equivalent resistance from the Vo terminal (in AC) and the input equivalent resistance from the Vs terminal (in AC). Hint: the transistor is a Si-based one. You have to write all the calculation details and verbal explanations. You can calculate hie = beta * 26mV / Ie (mA, dc) and use the hoe as an open circuit.
(RS=RC1=RE1==3k, R1=100k,R2=25k, R3=500k, RE2=6k, RL=4k, β1=100, β2=200,VBE1=VBE2=0.7V, VT=26mV) Find the voltage gain, input and output resistance of the circuit.
DESIGN PROJECT Single-Stage Common Emitter Class A AmplifierVoltage Divider Bias Circuit Supply: 10 Vdc to 24 VdcLoad: 1 kΩVoltage Gain: 80 to 400Lower Cutoff Frequency: 100 HzSinusoidal source (zero internal resistance): 50 mVp−pTransistor: Si, β = 75;Base-Collector capacitance= 8 pF; Base-Emitter Capacitance= 25 pF
Determine IDQ and VGSQ for voltage divider bias configurationfor the JFET using graphical analysis. In addition to obtaining the VD, VSand VDS.We have the following data of the different elements of the circuit, such as:R1 = 3.3 MΩ, R2 = 3.3 MΩ, RD = 860 Ω, RS = 2.2 kΩ and powered by one source 12 volts. The manufacturer's sheet indicates that IDSS = 12 mA and VP = −3 V. Include the transfer characteristic graph to obtain the values of thepoint Q.
Figure 1 shows a well-known circuit configuration with the bypassed source resistor using an n-channel D-MOSFET with yos = 20µS. (iv) Calculate transconductance, gm and rd. (v) Calculate the input, Zi and output impedance, Zo for the circuit. (vi) Prove that the equation for the no-load Gain, AvNL, for the circuit is as follows: AvNL = -gm (RD X rd / RD + rd) (vii) Calculate the no-load gain AVNL. (viii) Find the value of VoNL if Vi = 30 mV.
I - Design a CS amplifier using E-MOSFET with voltage gain 20dB , VGS=5V , VDD=12V ( gm=4500μS ).II - A JFET datasheet gives VGS(OFF) = -4V and IDSS = 5 mA. Determine the values of ID for VGS from 0 V to -5V in 1V steps. Plot the transfer curve from these data on a graph sheet.
IDQ = 0.8 mA, VDSQ = 3.2 V, Rin = 160 kΩ and fL = 16Hz a-) find RD, R1 and R2? Kn = 0.5 mA/V2, VTN = 1.2V ve λ =0 b-)middle band voltage gain? c-) Find the values of the voltage gain at f = 5Hz and f = 25 Hz.
The no-load voltage gain of the amplifier used in the circuit in the picture is K = 2000, input resistance R1 = 50K and output resistance Ro = 500ohm.a) Calculate the voltage gain of the circuit Vo / Vg.b) Calculate the value of the capacitors C1 and C2, considering that the lower cut-off frequency of the circuit is 20Hz and the asymptote slope is desired to be 40db / decade.c) Calculate the upper cut-off frequency of the circuit.
A cascade amplifier is to be designed to meet these specifications: Aυ = 5000 Rin ≥ 10 MΩ Rout ≤ 0.1 Ω How many amplifier stages will be required if the stages must use an op amp below? Because of bandwidth requirements, assume that no individual stage can have a gain greater than 50. Op amp specifications: A = 85 dB Rid = 1 MΩ Ro = 100 Ω Ric ≥ 1 GΩ
Data sheet below shows design parameters for a Common Source FET Transistor amplifier.VDD = 12V , VD = 0.75 VDD , VG = 0.5 VDD , Cin = Cout = 5muF , K = 1mAV-2 , VTN = 1V , R2 = 10k and ID = 2mA Q. At DC condition,design the circuit by calculating values for VG,R1,RD,VGS,RS and gm of the FET amplifier (show all the calculated steps involved). Propose and draw the DC circuit from the calculated values.
Since Vcc = 25 V, Vi = 36 mV, RB = 470 kΩ, RC = 3.1 kΩ, RE1 = 470 Ω, RE2 = 1.2 kΩ, RL = 56.2 kΩ and β = 110 in the circuit in the figure, find the value of the output voltage (Vo). NOTE-1: Capacitors are negligible at mid-band frequency. NOTE-2: The output impedance (r0) of the transistor will be neglected.