The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m3/kg Find the specific entropy in kJ/kg at state 2 to 3 decimal places.

The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m3/kg Find the specific entropy in kJ/kg at state 2 to 3 decimal places.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414 atm reheat pressure, the throttle and reheat temperature of the steam is 1302 R, condenser pressure is 4.3 kPa. Determine the difference between the simple Rankine cycle efficiency and the reheat Rankine cycle efficiency, in percent.
In a Rankine cycle steam enters the turbine at 2.5MPa (enthalpies and entropies given) and condenser of 50KPa (properties given), what is the thermal efficiency of the cycle? At 2.5MPa: hg = 2803.1 sg = 6.2575, At 50KPa: sf = 1.0910 sfg = 6.5029 hf = 340.49 hfg = 2305.4 vf = 0.0010300
In a Rankine cycle steam enters the turbine at 2.5 MPa (enthalpies & entropies given) and condenser of 50 kPa (properties given), what is the thermal efficiency of the cycle? At 2.5 MPa: hg = 2803.1 kJ/kg; sg = 6.2575 At 50 kPa: sf = 1.0910; sfg = 6.5029; hf = 340.49; hfg = 2305.4; vf = 0.0010300
Assume a basic (non-regenerative) ideal Brayton cycle where air modeled as IG with variables specific heat. The gas-turbine engine has the following operational parameters: Inlet Air Temperature:537 R Inlet Air Pressure:14.696 psia Compressor Pressure Ratio (rp):6.0 Firing Temperature:2400 R Heat Recovery Steam Generator: Assume that the exhaust from the gas turbine engine is directed to a heat recovery steam generator (HRSG)to produce wet steam (i.e. saturated vapor) at a pressure of 600 psia. Liquid water is supplied to the HRSG at 100F and 600 psia. The exhaust gas from the gas-turbine engine leaves the HRSG at the saturation temperature of the wet steam. With these conditions determine: a) the exit temperature of the wet steam (F), b) the intensive steam production rate, lbm-steam/lbm-exhaust gas. Absorption Chiller CHP: Assume the process steam from the HRSG is now used to drive an absorption chiller with COP of 0.7, and that the mechanical power of the gas-turbine engine is used…
Steam enters the turbine of a power plant operating on the Rankine cycle (Fig. 2) at 873.15 Kand exhausts at 30 kPa. To show the effect of boiler pressure on the performance of the cycle,calculate the thermal efficiency of the cycle and the quality of the exhaust steam from theturbine for boiler pressures of 5000,7500, and 10 000 kPa. #Chemical Engineering #Chemical #Thermodynamics
1. In a Rankine cycle, steam enters the turbine at 2.5 MPa and condenser at 50 kPa, what is the thermal efficiency of the cycle?At 2.5 MPa: hg = 2803.1 kJ/kg sg = 6.2575 kJ/ kg – KAt 50 kPa: sf = 1.0910 sfg = 6.5029hf = 340.49 hfg = 2305.4vf = 0.0010300
Solve the Rankine Cycle problems. Draw a detailed Schematic and Ts Diagram. Show a clear and detailed solutions. 1, Consider a steam power plant that operates on an ideal reheat Rankine Cycle.The Plant maintains the boiler at 8MPa, the reheat section at 700kPa.and the condenser at 10kPa. The mixture quality at the exit of both turbines is 93%. Determine the temperature at the inlet of each turbine .
Explain briefly the operating conditions which affect Rankine cycle efficiency. What are the methods of improvement?
Problem 1: The boiler of a power steam cycle operates at 6000 kPa and the condenser at 50 kPa. At the entrance to the turbine, the temperature is 500°C. The isentropic efficiency of the turbine is 90 percent, pressure and pump losses are negligible, and the water leaving the condenser is subcooled by 6.3°C. The boiler is sized for a mass flow rate of 18 kg/s. You are asked to: a. Represent the cycle on P-v and T-s diagrams. b. Compute the rate at which heat is added in the boiler. c. Compute the power required to operate the pumps. d. Determine the net power produced by the cycle. e. Compute the thermal efficiency.
A gas turbine power plant operates on a simple thermodynamic cycle. The ambient conditions are 100 kPa and 24 °C. The air at this condition enters the engine at 150 m whose diameter is 0.5 m. The pressure ratio across the compressor is 13, and the temperature at the turbine inlet is 1400 K. Assuming ideal operation for all components and specific heats for air and products separately. In addition, neglect the mass of fuel burned. Do the followings: a. Choose the suitable thermodynamic cycle b. Draw pv and Ts diagram and label it c. Calculate the power required by the compressor d. Determine the pressure and the temperature at the turbine exit, e. Compute the power produced by the turbine f. Available specific work g. The thermal efficiency.
The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4 : Inlet steam at 17.5 MPa and 600 degrees Celsius 6-1 : Inlet steam at a pressure of 11,16 kPa at a wetness fraction of 0,1. At state 1, the specific volume is 0,00101 m³/kg 1) Use the prescribed steam Table. Thermodynamic and transport Properties of fluid table by GFC Rogers and YR Mayhew Give the required properties at given states by completing the table 2)Show the working of the values provided in the table, such as interpolation steps and pump work. 3)determine the specific heat input to the system 4)determine the specific heat output from the system 5)determine the thermal efficiency of the cycle 6)Sketch an appropriate T-s diagram of the gas-steam combine cycle and indicate the diagram's important state point and values.
A simple Rankine cycle uses water as the working fluid. Water enters the pump as a saturated liquid at 10 kPa and exits at a pressure of 5 MPa. Water enters the condenser as a saturated mixture with a quality of 90%. Assume that the cycle is ideal. 1. What is the temperature of the turbine inlet, in °C? Report your result to one decimal place using rounding. 2. How much heat was added in the boiler, in kJ/kg. Round to the nearest whole number. 3. How much heat was removed in the condenser? Round your answer to the nearest whole number. 4. What is the net work produced, in kJ/kg. Round your answer to the nearest whole number.