The following data were obtained by a stadia measurement; vertical angle is 30°23', and observed stadia intercept is 2.20m. The stadia interval factor at the measurement used 95.50m and C is 0.30m, if the height of the instrument is 1.62m, and the rod reading is taken 1.95m. Determine the HD, VD, ID, and DE. Given: K= 95.5m S= 2.2m C = 0.3m Vertical Angle = 30°23' ERSITY

The following data were obtained by a stadia measurement; vertical angle is 30°23', and observed stadia intercept is 2.20m. The stadia interval factor at the measurement used 95.50m and C is 0.30m, if the height of the instrument is 1.62m, and the rod reading is taken 1.95m. Determine the HD, VD, ID, and DE. Given: K= 95.5m S= 2.2m C = 0.3m Vertical Angle = 30°23' ERSITY

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

A piston ring of outer diameter 1.5354in and inner diameter of 1.496in is placed in a ring gage of DIA 1.537. The in-clearance width measured at the gap of the piston ring in 0.0159in. Calculate the corrected in-clearance if the piston ring is placed in a ring gage of DIA 1.5354in.
Recall that power available at altitude is (rho/rho0)*power at sea level. Include transmission losses! [~, a, ~, RHO, ~] = atmosisa(alt(k1)*0.3048); rho=RHO*0.0685218/35.3147; rho_scale=rho/rho0; a=a/0.3048;
a) Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a= 1.500 ± 0.001 in b= 2.000 ± 0.003 in c= 3.000 ± 0.004 in d= 6.520 ± 0.010 in Determine the mean gap ￣w and its tolerance. Determine the mean size of d that will assure that w ≥ 0.010 in. b) A 1-in-diameter rod, 3 ft long, of unknown material is found in a machine shop. A variety of inexpensive nondestructive tests are readily available to help determine the material, as described below with results in bracket: i. Visual inspection. (Dark gray, rough surface finish, moderate scale) ii. Check if it is attracted to a magnet. (Yes) iii. Measure Weight. (7.95lbf) iv. Inexpensive bending deflection test: Clamp one end in a vise, leaving 24 in cantilevered. (5/16in) v. Brinell hardness test. (HB = 200)
A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance measured along the beam; [x]=[L] y = displacement of the beam; [y]=[L] = circular frequency of vibration; []=[T1] = mass of the beam per unit length; []=[ML1] D = bending rigidity of beam; [D]=[FL2] Show that the equation is dimensionally homogeneous. Note that [F]=[MLT2] see Eq. (1.21:).
The turning moment diagram for a multi-cylinder engine has been drawn to a scale of 1 mm= 4500 N-m vertically and 1 mm = 2.4° horizontally. The intercepted areas between outputtorque curve and mean resistance line taken in order from one end are 342, 23, 245, 303, 115,232, 227, 164 mm2, when the engine is running at 160 r.p.m. If the mass of the flywheelis 1000 kg and the total fluctuation of speed does not exceed 3% of the mean speed, find theminimum value of the radius of gyration.
Part (a) and (b) only Answer for (a): Radial interference = .00205 in Corresponding interface pressure= 13.3 kpsi
A pressure measurement system is stated as having the followingcharacteristics. Explain the significance of the terms:Range: 0 to 125 kPa and 0 to 2500 kPaAccuracy: ±1% of the displayed readingTemperature sensitivity: ±1% of the reading per o C
Presents the diagram of the problem, necessary formulas, clearance and numerical solution Make the following conversions to the requested units: a) 120 ◦C at ◦F b) 0K at ◦C c) 0 K to ◦F d) 412 ◦F at K e) -12.5 ◦C to ◦F
The windscreen washers of an old car don't work (W = 0). This could be for two reasons: the windscreen fluid tank is empty (E = 1) or the tube is has a blockage (B = 1). Being an old car, the light to indicate that the windscreen fluid tank is empty only comes on (L = 1) 75% of the time. It will sometimes comes on even if the tank has some fluid in it, with probability 0.25. Of course the tube could be both blocked and the tank empty. (a) Draw the Bayesian network describing the scenario just described, and express the joint probability in factorised form, defining appropriate variables.
If a 5.5 kg weights are added to bourdon gauge the reading on the of the gauge should be (assuming no error ) Select one: a. none b. 0.171224 N/mm2 c. 171.22KN/m2 d. 0.01746 KG/mm2
correction the given its + sign not - (0.14 t^4 + 4.1t^3 + 0.12t^2) answer by step thank u..
27.) The following are ways to determine the internal energies and enthalpies of ideal gases EXCEPT: a.By using the tabulated p and v data. b.By using average specific heats. c.By using the tabulated u and h data. d.By using the cv or cp relations and integration 23. The energy equation theta = u + pv+ pe+ ke applies to flowing fluids Select one: True False