نقطة واحدة The measuring instruments-10 may be classified in to two groups a- absolute instruments and secondary instruments. b- indicating and integrating instruments. نقطة واحدة * Gross errors are-11 a-Humans errors. b- Systematic errors. c- Random errors. * نقطة واحدة percentage error equal-12 a- XT-Xm/XT *100 O B- 1- XT - Xm/XT O

نقطة واحدة The measuring instruments-10 may be classified in to two groups a- absolute instruments and secondary instruments. b- indicating and integrating instruments. نقطة واحدة * Gross errors are-11 a-Humans errors. b- Systematic errors. c- Random errors. * نقطة واحدة percentage error equal-12 a- XT-Xm/XT *100 O B- 1- XT - Xm/XT O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a Measurement ,the Expected value is 94 V and the measured value is 88 V. Find (i) absolute error Ea , (ii)Relative error Er, (iii) Absolute accuracy Aa (iv) Relative Accuracy Ar.
1.The thickness of a gage block is measured five times using an instrument that has a resolution of 0.001 cm. The following measurements are obtained (in cm): 1.100, 1.110, 1.090, 1.095, and 1.105. The true gauge block thickness is known to be 1.050 cm. Use this information to answer the following questions: a. What errors or sources of measurement error can be identified in the example? (Hint: there are three). Identify each one as a random or systematic uncertainty. b. Estimate the magnitudes of each of these uncertainties. Wherever possible, estimate random uncertainties at a 95% probability/confidence level. c. Based on the uncertainties determined in part b, estimate the overall uncertainty of a measurement obtained by this instrument.
TOPIC: ERROR IN MEASUREMENT Measurements are precise but not accurate. A. Random Error B. Gross Error C. Systematic Error EXPLAIN!
In a Measurement the Expected value is 10 V and the measured value is 71 V, Find O absolute eror Ea (ORelative error Er, (ii) Absolute accuracy Aa (iv) Relative Accuracy ) Absolute Error= (i)Relative error= (i) Absolute accuracy= (iv) Relative Accuracy
To measure the density of a stone, a digital scale and a beaker cup filled with water are used. The balance is used to measure the mass of the stone, while the beaker is used to measure the volume of the stone. It is known that the digital balance has a resolution of 0.1 g and that the beaker cup has a resolution of 5 ml. Repeated mass measurements return the following values: 250.0 g; 249.9 g; 250.3 g; 249.6g; 250.1 g; 249.7g; 250.4 g; 250.0 g; 248.8 g; 250.2 g The volume is measured only once. Placing the stone in the beaker, a volume of displaced water equal to 50 ml is measured. Using a k=2.5, check if the density of the stone is compatible or out of line with the value ρ = (4910 ± 65) kg.m-3 (a) none of the above (b) the values are compatible (c) missing data to perform the compatibility test (d) the values are discrepant
We wish to measure a characteristic of a machined part whose nominal size is 50 mm at 20 °C. For this, two different instruments are used; an analog micrometer and a digital vernier caliper, both recently calibrated and with the same resolution (0.01 mm). The calibration certificate data of the analog micrometer and the digital vernier are shown in tables 5 and 6 respectively. In both cases the calibration uncertainty does not include the contribution of resolution uncertainty. Additionally, there are drift studies for both instruments and it is established that the drift of the micrometer is ± 0.002 mm while the drift of the vernier is ± 0.02 mm. The same number of measurements were performed with both instruments to avoid repeatability biases under controlled environmental conditions. Table 7 shows the results of the measurements of both instruments. The temperature of the piece was monitored with a digital thermometer whose calibration uncertainty is 0.1 °C, which already includes…
Question 1 (a) Explain what you understand by the term Callibration. (b) Describe in details the process of calibrating a digital industrial thermometer. Question 2 (a) Explain the importance of Primary, secondary and tertiary standards employed in Metrology. (b) By giving appropriate examples outline the advantages and disadvantages of Line and end standards. Question 3 Describe the types of errors and defects encountered in measuring instruments used in metrology.
The error values in a measurement system are -5, -3, -1, -7 and it is said to be systematic error. true OR false
Truncation errors are increased as the round-off errors are decreased.Group of answer choices True False Say, you have a thermometer and you are checking the temperature of a body that has a temperature of 36o Using your thermometer five times, it gives you the following measurements: 29oC, 29.2oC, 29.3oC, 28.9oC, and 29.1oC. What can we conclude about the accuracy and the precision of the thermometer?Group of answer choices The thermometer is not accurate and not precise The thermometer is faulty. The thermometer is accurate and precise The thermometer is not accurate but precise. Say, you have a thermometer and you are checking the temperature of a body that has a temperature of 36o Using your thermometer five times, it gives you the following measurements: 36oC, 35.6oC, 36oC, 37oC, and 36.2oC. What can we conclude about the accuracy and the precision of the thermometer?Group of answer choices The thermometer is accurate and precise. The thermometer is accurate but not precise. The…
A displacement transducer has the following specifications: Linearity error: ±0.25% reading Drift: ±0.05%/°C reading Sensitivity error: ±0.25% reading Excitation: 10-25 V dc Output: 0-5Vdc Range: 0-5 cm The transducer output is to be indicated on a voltmeter having a stated accuracy of 0:1% reading with a resolution of 10 μV. The system is to be used at room temperature, which can vary by 10 °C. Assume 95% confidence. The displacement transducer above is used in measuring the displacement of a body impacted by a mass. Twenty measurements are made, which yield Determine a best estimate for the mass displacement at 95% probability based on all available information.
A displacement transducer has the following specifications: Linearity error: ±0.25% reading Drift: ±0.05%/°C reading Sensitivity error: ±0.25% reading Excitation: 10-25 V dc Output: 0-5Vdc Range: 0-5 cm The transducer output is to be indicated on a voltmeter having a stated accuracy of 0:1% reading with a resolution of 10 μV. The system is to be used at room temperature, which can vary by 10 °C. Assume 95% confidence. The displacement transducer above is used in measuring the displacement of a body impacted by a mass. Twenty measurements are made, which yield X= 17.20mm Sx= 1.70mm Determine a best estimate for the mass displacement at 95% probability based on all available information.
Discuss the importance of measuring devices for Electric Motor and Internal Combustion Engine in terms of accuracy.