The following program is written in the assembly language of 8085 processor: LXI B, 20DF LXI H, 2B44 MOV A, C SUB B MOV A, L ADD H INX B DCX H HLT (a) Complete Table 1 with the machine codes and memory addresses for the whole program by using 8085.jar simulator. (b) Determine the total number of bytes needed to execute the whole program. (c) State final value of all registers involved in the program.

The following program is written in the assembly language of 8085 processor: LXI B, 20DF LXI H, 2B44 MOV A, C SUB B MOV A, L ADD H INX B DCX H HLT (a) Complete Table 1 with the machine codes and memory addresses for the whole program by using 8085.jar simulator. (b) Determine the total number of bytes needed to execute the whole program. (c) State final value of all registers involved in the program.

Name: (a)(b) No. of bytes:(c)Memoryaddress0000Register Final valueABсHLTabl
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: (a)(b) No. of bytes:(c)Memoryaddress0000Register Final valueABсHLTable 1Machine code MnemonicsLXI B, 20DFLXI H, 2B44MOV A, CSUB BMOVA, LADD HINX BDCX HHLT The following program is written in the assembly language of 8085 processor:LXI B, 20DFLXI H,

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 2PE: If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the...

See similar textbooks

Similar questions

Consider a HW ISA program P1 with the following Instruction Memory IM: a. fill in the execution table for program P1 using the IM. Use the same notational conventions used in the example execution table for P0 below. Any numbers beginning with 0x will be interpreted as hexidecimal; any numbers not beginning with 0x will be interpreted as decimal. b. Show the final values of the registers R2, R3, and R4 when the program execution halts. Again, any numbers beginning with 0x will be interpreted as hexidecimal; any numbers not beginning with 0x will be interpreted as decimal.
Task#1: Assembly Language Programming: Write down the states of RAM and registers, in line by line Debugging Mode, in the following given scenarios. [org 0x100]mov ax, 3add ax,1mov ax,2mov bx,3sub bx,axadd ax,bxmov ax,0x4c00int 0x21 Solution: Ax = Ax = Ax = Ax = and Bx = Ax= and Bx= Ax= and Bx= Ax= and Bx= only 7 min left do fast donot copy from internet there it is wrong
Consider the following program in MARIE assembly language. a) Complete the table detailing the RTN for next 2 instructions only that will be executed including the content of registers PC, IR, MAR, MBR and AC in hexadecimal. Note the first instruction LOAD X is already filled. Note also that SKIPCOND instruction has no operands, therefore you can complete Fetch, decode and execute cycles only. b) Explain in one statement the task performed by this program?
Consider the following program in MARIE assembly language. a) Complete the table detailingthe RTN for next 2 instructions only that will be executed including the content of registers PC,IR, MAR, MBR and AC in hexadecimal. Note the first instruction LOAD X is already filled. Notealso that SKIPCOND instruction has no operands, therefore you can complete Fetch, decode andexecute cycles only. b) Explain in one statement the task performed by this program?
Assemble the following assembly code into machine code. Assume thatthe machine language op-codes for load, store, mult, add, div, and subare 18, 19, 13, 14, 15, and 16, respectively. Also assume that the variablex is stored at location M[50].a. load R1, x mult R2, R1, #9 store x, R2 b. sub R0, R1, #8 div R2, R0, #2
In a register/memory type CPU, the instruction lengths are typically variable. This presents a problem when the program is incremented during the Fetch-Decode-Execute cycle. What statements(s) is/are NOT TRUE with regard to Program Counter (PC) incrementing? Select one or more A. The binary loader overcomes the problem by positioning instructions at word boundaries so that PC can be calculated. B . PC is incremented by the largest possible foxed value, irrespective of the variability of the instruction C. Increment value is known when the current instruction has completed execution. D. increment value is known when the current instruction is decoded with the Instruction Register (IR) E. PC incrementing method is implementation dependent
Computer Science Assembly language 218 Q18: Given the code fragment: lst dd 2, 3, 5, 7, 9 mov rsi, 4 mov eax, 1 mov rcx, 2 lp: add eax, dword [lst+rsi] add rsi, 4 loop lp mov ebx, dword [lst] What would be in the eax ebx registers after execution (in hex)? Note, must precede hex number with 0x.
The register content for an Intel 8086 microprocessor is as follows:CS = 1000H, DS = 2000H, SS = 5000H, SI = 2000H, DI = 4000HBX = 6783H, BP = 7000H, AX = 29FFH, CX = 8793H, DX = A297HCalculate the physical address of the memory where the operand is stored and the contents of the memory locations in each of the addresses shown below: a) MOV [SI], ALb) MOV [DI+6H], BXc) MOV [SI+BX–11], AXd) MOV [DI][BX]+28H, CXe) MOV [BP][SI]+17, DX
Consider the following instruction sequence where registers R1,R2 and R3 are general purpose and MEMORY[X] denotes the content at the memory location X. InstructionMOV R1,(5000)MOV R2,(R3)ADDR2,R1MOV (R3),R2INC R3DEC R1BNZ 1004HALTSemanticsR1←MEMORY[5000]R2←MEMORY[R3]R2←R1+R2MEMORY[R3]←R2R3←R3+1R1←R1−1Branch if not zero to thegiven absolute addressStopInstruction Size (bytes)44242221 Assume that the content of the memory location 5000 is 10, and the content of the register R3 is 3000. The content of each of the memory locations from 3000 to 3020 is 50. The instruction sequence starts from the memory location 1000. All the numbers are in decimal format. Assume that the memory is byte addressable. After the execution of the program, the content of memory location 3010 is
Assume that the registers have the following values (all in hex) and that CS=1000, DS=2000, SS=3000, SI=5400, DI=2200, BX= 6000, BP-1000, SP= 1100, AX=4312, CX=11CB, and DX= 2245. Calculate the physical address of the memory where the operand is stored and the contents of the memory locations in each of the following addressing examples: 1- MOV (SI), DL. 2- MOV [DI-9), CH 3- MOV [BP], AL. 4- MOV (SI+BX]. AH. 5- MOV BX, 22AC. 6- MOV [SI]+50, BX. 7- MOV [2000]. DX. 10- MOV (SP), BH. 8- MOV BL, DH 9- MOV [BX]+10, AX.
Assume that the operation times of one add instruction for the major functional units are 325 ps for memory access, 185 ps for ALU operations and 125 ps for register file read/writes. Please fill the table first and perform the following a )What is the total cycle in single-cycle implementation? b )What is the total cycle in pipelining implementation? c) What is the total cycle in pipelining implementation if there are 5 million add instructions? d) What is the total cycle in pipelining implementation for 5 million add instructions, if the stages are balanced? e)What is the speed up of pipelining implementation over single-cycle implementation?
Q1: Suppose the hypothetical processor has two I/O instructions: (3+3+3)0011=Load AC from I/O0111=Store AC to I/OIn this case, the 12-bit address identifies a particular external device. Show the program execution using figure for the following program:a) Load AC from device 6b) Add contents of memory location 880c) Store AC to device 7 (Note: Question is to be solved similar to the pictures attached with minimum explaination of a line or two with the steps and SHOULD include the memory location 880 as stated in the question)