The force of 500 N is the resultant of the forces P and 250 N acting as shown in the figure. Compute the following: (a)the angle that the 500 N makes with the horizontal, (b)the value of a and (c) the value of P. 2. The force of 500 N is the resultant of the forces P and 250 N acting as shown in the figure. Compute thefollowing:a)the angle e that the 500N makes with the horizontal, (b)the value of a and (c) the value of P.y500NyP4260N

Given resultant force =500N The two forces are P and 250N tanθ=43θ=tan-143θ=53.13°…

The force of 500 N is the resultant of the forces P and 250 N acting as shown in the figure. Compute the following: (a)the angle that the 500 N makes with the horizontal, (b)the value of a and (c) the value of P.

The force of 500 N is the resultant of the forces P and 250 N acting as shown in the figure. Compute the following: (a)the angle that the 500 N makes with the horizontal, (b)the value of a and (c) the value of P.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For the structures loaded as shown, calculate the moment produced by forces about points A, B and C.…

A: Consider the figure,

Q: Determine the work of the force when it displaces 5m as shown in the figures. With free diagram.

A: Using principal of work done by force

Q: Q1:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: From the figure, sinθ=45 and cosθ=35 Consider the following figure.

Q: The strengths of the forces in the figure are P = 80 N and Q = 110 N. Find the direction and…

A: Question is based on section subject to two forces P and Q. Length of members , angle and magnitude…

Q: uestion 5 Determine the magnitude of the resultant force and its direction measured Counterclockwise…

A: Resolving forces in x and y directions as-

Q: |20 lb 12 |A I in. 80 lb 3 B

Q: A 500 N force acts at the origin of the x and y axes at 215 degrees measure counterclockwise from…

A: Let u Component of the 500 N force be called as FuLet v Component of the 500 N force be called as Fv

Q: The frame shown in the figure is supported by a hinge at A and a roller at E. Compute the vertical…

A: Compute the vertical components of the hinge forces at C

Q: To determine the reaction forces at supports on a horizontal beam by using the equations of…

Q: Problem#4. Replace the force F having a magnitude of F=53lb and acting at point A by an equivalent…

A: Replace the force F having a magnitude of F=53lb and acting at point A by an equivalent force and…

Q: A hook is subjected to three forces A, B, and C as shown. Force A = 35 kN and force B = 45 kN. a) If…

A: Given, Force, A = 35 kN Force, B = 45 kN The given problems can be answered by resolving the…

Q: $) The gate shown in the figure below is a quarter circle and hinged at point H. Determine the…

Q: 1. The resultant of four forces of which 3 are shown in the figure is a clockwise 480 lb-ft couple.…

A: Draw the figure. Let F4 be the fourth force.

Q: 50 N 2m 60 60 N D Im Im в 30 N 2m 70 N

A: Determine the magnitude, direction and position (with respect to A) of the resultant of a force…

Q: Determine (a) the magnitude S of vector sum S = A + B of the two concurrent forces concurrent as…

A: Hello dear this is the solution of your problem Please see the attached solution, thanks

Q: Given the system of forces shown below, Determine the following: (a) Moment of the 224-lb force…

A: According to guidelines we are supposed to solve only first three subbparts AMoment of 224 lb…

Q: Determine the x, y, and z scalar components of the force. F= 21 kN 3 m Im m, 2 m

A: Given Data : Force, F = 21 KN

Q: *19. A beam supporting a uniform load of intensity q throughout its length rests on pistons at…

Q: Situation 1: The 300-lb force is to be resolved into components along lines a-a' and b-b'. a 300 lb…

A: Given data in question Load Angle To find out Components

Q: Solve the resultant of the given concurrent forces.Given angle = 30 degrees

A: From the given question it is required to determine the resultant of the given concurrent forces.

Q: PROBLEM #4: Given the beam loaded as shown in the figure. Neglecting the weight of the beam. a.…

Q: A mass of 200 kg is supported by a bar, pulley, and cable as shown in the figure. Determine a) the…

A: Given: The mass m is 200 kg. Consider the figure,

Q: Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the…

A: To find the resultant force decrease the magnitude of the lesser force from the magnitude of the…

Q: For the figure shown, determine the following: a.) The moment of the force 300 N at points A and B…

A: From the above figure - For the 300N of force - FH300 = 300×(35)FH300 = 180N And FV300 =…

Q: Ql:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: According to the guidelines, I am supposed to solve only the first question Solution Given the…

Q: Determine the resultant of the four forces acting on the body shown. 200 N 60° 150 N 12 30° 350 N

Q: Ql:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: Given the coplanar system of forces and moments

Q: Q1:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: Given the coplanar system of forces and moments

Q: +y A B a +x 12 Three coplanar, concurrent forces at O Vertical component of force B will act along…

Q: In the figure, the rigid AD bar is held vertically by two elastic rods articulated at the ends,…

A: Let horzontal reaction at B and C is Hb and Hc and Hc respectively, and verticalreaction at D is…

Q: A rectangular gate AB hinged at A has a width of 2.0 m perpendicular to the paper and has negligible…

Q: What is the concentrated load of the rectangular loading as shown in the figure? What is the…

A: Given:- A loading as shown below

Q: :) The gate shown in the figure below is a quarter circle and hinged at point H. Determine the…

Q: Ql:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: NOTE : 1) Since you have asked multiple questions, we will solve the first question for you. If you…

Q: he moment of the force about each of the coordinate axes.

A: Moment is a rotation force in an object due to external force applied on it.

Q: Consider the object shown in (Figure 1). Suppose that P = 220 N , M = 790 N⋅m . Follow the sign…

A: Determine the internal normal force at point C. Determine the internal shear force at point C.…

Q: The frame is subjected to a distributed load which starts at 200 N/m at A and increases to 250N/m at…

A: a) Using the figure to the right of the frame, draw a free-body diagram of the frame. Label the…

Q: Q.3) For the figure shown, if the moment of the force F about the axis BC is 150 lb ·ft. B Determine…

A: Determine the position vector for the force F.…

Q: 3. The roller at point C in the figure below can only support a force of 55 O N. If the force P is…

Q: 2.5 m 2.5 m 600 N/m 600 N/m

A: Consider the given diagram

Q: The frame shown in the Figure is supported by a hinge at A and a roller at E. Compute the horizontal…

A: P=70kN X=6.8m To find horizontal components of the hinge forces at B

Q: Determine the resultant of the parallel forces system acting on the bar AB shown below and the…

Q: 2/88 If the resultant of the forces shown passes through point A, determine the magnitude of the…

A: Step 1

Q: A horizontal force of P = 200 N is just sufficient to hold the crate from sliding down the plane,…

A: The static friction coefficient is equal to the ratio of the maximum static friction force (F)…

Q: The tie rod is used to support this overhang at the entrance of a building. If it is pin connected…

A: Free body diagram of over hang beam: The total weight of overhang P lies at point B

Q: In the figure shown, the x component of the force P is 140 kN to the left. Determine P and its y…

A: Given data, X- component of P = 140 KN To calculate:- P and Py ?

Q: PROBLEM #4: Given the beam loaded as shown in the figure. Neglecting the weight of the beam. a.…

Q: A rigid bar is suspended by three rods made the same material as shown in the figure. The area and…

Q: The gate shown in the figure below is a quarter circle and hinged at point H. Determine the…

Q: The resultant of a force system on a bracket as shown in Figure is acting vertically upwards. If the…

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

2. The force of 500 N is the resultant of the forces P and 250 N acting as shown in the figure. Compute the
following:
a)the angle e that the 500N makes with the horizontal, (b)the value of a and (c) the value of P.
y
500N
y
P
4
260N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
Two steel pipe columns (E=200,000??a,A1=2000mm2,A2=1800mm2)support a rigid beam AC that has a 3.6m overhang BC. The beam supports a linearly varying load of maximum intensity w=75K/nm as shownin the figure.Neglect the weight of the beam AC, and assume that the beam is supported on the two columns such that it transmits load to each column as an axial load.Determine the vertical displacementat end C of the beam, in column 1at A and column 2at B. Answer in mm.
Compute the value of EIy at 2.5 m from the left support.
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
Determine the following unknowns on the beam shown below using Conjugated-Beam Method. Consider 250 mm x 250 mm and E = 200 GPa. Note: a = 4.5 m b = 33.0 kN/m c = 13 kN Find the ff. A. Vertical reaction at C in kN. B. Moment reaction at C in kN. C. Deflection at point B in mm. D. Maximum deflection on the beam in mm.
A rectangular beam is supported at both ends. It carries two concentrated load of 110kN, a clockwise moment of 110kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 60GPa. Solve the following if the reaction at point B is 328.90256410256kN, upward. BEAM DIMENSION: Width = 190mm , Height = 390mm NOTE: b = 4.8m ; Determine the deflection at midspan
Determine the following unknowns on the beam shown below using Conjugated-Beam Method. Consider 250 mm x 250 mm Section and E = 200 GPa. Note: a = 4.5 m b = 33.0 kN/m c = 13 kN Find the following A. Vertical reaction at C in kN. B. Moment reaction at C in kN-m. C. Deflection at point B in mm. D. Maximum deflection on the beam in mm.
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 6.4 × 104 kN·m2 is constant for the beam; w = 3.6 kN/m, LAB = 3.7 m, LBC = 7.4 m, LCH = 3.7 m.
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.
The rigid pole is supported by a pin at C and a wire AB. If the wire has a diameter of 0.5 cmand its modulus of elasticity is 200 GPa, determine how much it stretches when a horizontalforce of 12 kN acts on the pole and the new diameter of the wire. Assume the Poisson’s ratioof the wire is 0.32.
From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m. Determine the following;a. Reaction at A.b. Constant C1.c. Slope at L/3.d. Deflection at L/3.