19-20. The gear motor can develop 2 hp when it tums 450 rev/min. If the shaft has a diameter of 1 in.What is the torque developed by the power?A. 0.000707 lb-ftB. 23.34 lb-ftC. 127.83 lb-ftCS Delevina thamanimum shear strass deveiway to the shaft.A. 1426.60 psiB. 118.88 psi0.04323 psiD.280.11 lb-ftD. 0.0036 psimm diameter rivets.

Power developed by shaft = 2hp No. of turn=450rev/min Diameter of shaft=1 in To find Torque…

The gear motor can develop 2 hp when it turns 450 rev/min. If the shaft has a diameter of 1 in. What is the torque developed by the power? B. 23.34 lb-ft D.280.11 lb-ft C. 127.83 lb-ft A. 0.000707 lb-ft Detea tine (animum sheer stras devait the shaft. A. 1426.60 psi B. 118.88 psi 0.04323 psi D. 0.0036 psi

The gear motor can develop 2 hp when it turns 450 rev/min. If the shaft has a diameter of 1 in. What is the torque developed by the power? B. 23.34 lb-ft D.280.11 lb-ft C. 127.83 lb-ft A. 0.000707 lb-ft Detea tine (animum sheer stras devait the shaft. A. 1426.60 psi B. 118.88 psi 0.04323 psi D. 0.0036 psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown compute the magnitude of the force supported by the pin at C and the oil pressure p against the 3.58-in.-diameter piston of the hydraulic-cylinder unit AB.Assume a = 5 in., b = 33 in., c = 17 in., e = 36 in., and 26°. C=? LB p=? Lb/in^2
Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m
Flow In Closed Conduits 5. Water at 65F is pumped to a tank through a 750 ft 12-in diameter galvanized iron pipe and the flow is 4.5 cfs. (a) Determine the head lost due to friction. (b) How much power, in HP, is required to overcome this head loss? Answers: (a) _______________________________ (b) _______________________________
A centrifugal pump which runs at 104.3 rad ·s−1 (16.6 rev/s) is mounted so that its centre is 2.4 m above the water level in the suction sump. It delivers water to a point 19 m above its centre. For a flow rate of Q (m3 ·s−1) the friction loss in the suction pipe is 68Q2 m and that in the delivery pipe is 650Q2 m. The impeller of the pump is 350 mm diameter and the width of the blade passages at outlet is 18 mm. The blades themselves occupy 5% of the circumference and are backward-facing at 35◦ to the tangent. At inlet the flow is radial and the radial component of velocity remains unchanged through the impeller. Assuming that 50% of the velocity head of the water leaving the impeller is converted to pressure head in the volute, and that friction and other losses in the pump, the velocity heads in the suction and delivery pipes, and whirl slip are all negligible, calculate the rate of flow in liter/s and the manometric efficiency of the pump.
Neglect friction of the 55-Ibf collar against its vertical guide and compute the velocity of the collar after it has fallen 7ft., starting from22 ft/sec. in the position shown below. The unstretched length of the spring is 3ft.
The 100-mm-diameter pulley shown fits loosely on a 10-mm-diameter shaft for which the coefficient of static friction is Determine the minimum tension T in the belt needed to (a) raise the 100-kg block and (b) lower the block. Assume that no slipping occurs between the belt and pulley and neglect the weight of the pulley Choices: A. TMAX = 1075 N, TMIN = 906 N B. TMAX = 1075 N, TMIN = 690 N
he 30o directional pressure pipe elbow in the vertical plane is 60 cm in diameter. from the elbowThe flow rate of the current passing is 1 m3/s. At the lower end (1) of the elbow, the pressure is 70 kPa and the ground level is 30 m, the upperAt the end of the section (2), the ground level is 31 m. The fluid is water (ρwater=1000 kg/m3), frictionless and incompressible.taking into account thata) Find the velocities in sections (1) and (2) and the pressure in section (2).b) The weight of the pipe at the elbow is 1400 N. In case the length between sections is 1.2 mIn order to keep the elbow stable, taking into account the mass of water in the elbow, in the vertical directionCalculate the force that must be applied.
Fluid mechanics, i need solutions in 10 minutes please. Q/Q2 The 4 -m- diameter circular gate of Fig. E2.6a is located in the inclined wall of a large reser voir containing water (y = 9.80 kN / m³). The gate is mounted on a shaft along its horizon tal diameter. For a water depth of 10 m above the shaft determine: (a) the magnitude and lo cation of the resultant force exerted on the gate by the water, and (b) the moment that would have to be applied to the shaft to open the gate.
The motor shown supplies 4 kW at 2 Hz at A. Shafts (1) and (2) are each solid 30-mm-diameter steel [G = 80 GPa] shafts with lengths of L1 = 835 mm and L2 = 1160 mm, respectively. The bearings shown permit free rotation of the shafts. Determine the rotation angle of gear D with respect to flange A. 0.1035 rad 0.0973 rad 0.1149 rad 0.0706 rad 0.1472 rad
A 10m diameter storage tank, 15m high is used to contain four different liquids. 2.50m of liquid A(SG=085), 5m of liquid B(SG=2.40), 3.80m of fresh water, and 2.70m of liquid CSG=7.79). It is provide with two steel bands installed 1m from the top and 1m from the bottom. Determine the : a) total hydrostatic force acting on the wall of the tank. b) the line of action of the total force from the bottom c) tensile force at the top band and the tensile force at the bottom band. Please draw the complete pressure diagram with proper labelling.
A pump draws water from reservoir A and lifts it to a higher reservoir B, as shown in Figure P4.2.6. Thehead loss from A to the pump is four times the velocity head in the 10cm pipe, and the head loss fromthe pump to B is seven times the velocity head. The pressure head at the inlet of the pump is -6m .Compute the pressure head the pump must deliver. Why is the pressure head the pump must delivergreater than 50m , the elevation difference between the two reservoirs? Draw the EGL and HGL
The 2kg collar is released from rest at A and slides down the inclined fixed rod in the vertical plane. The coefficient of kinetic friction is 0.40. Calculate the a. Velocity of the collarwhen the spring has been compressed 40mm b. Velocity of collar before it hits the spring