The heat engine shown in the figure uses 2.00 mol of a monatomic gas as the working substance. (a) What is the Carnot and thermal efficiency for this engine? (b) Draw a scaled energy- transfer diagram for the situation that includes values for QH, Qc, and W. Answer: 66.7%, 5.88% P (kPa) 600 400 3 200 V (m) 0.025 0.050

The heat engine shown in the figure uses 2.00 mol of a monatomic gas as the working substance. (a) What is the Carnot and thermal efficiency for this engine? (b) Draw a scaled energy- transfer diagram for the situation that includes values for QH, Qc, and W. Answer: 66.7%, 5.88% P (kPa) 600 400 3 200 V (m) 0.025 0.050

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

18.) Water vapor at a flow rate of 20000 kg / h enters a steam boiler with a specific volume of 150 kPa 0.001053 m3 / kg. The energy of the boiler in the combustion chamber rises to 1200 kpa at 150 ° C. If the boiler has poor insulation and loses heat to the environment of 100 kW, calculate the time required to increase 1 ton of water to 150 ° C in the boiler?A.) 648sB.) 2494sC.) 1651sD.) 3752 sE.) 347 s
1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes saturated. It is withdrawn and reheated to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa. For the steam table: https://drive.google.com/drive/folders/1WTb6WwrXs2FR8Y92B3exTPKm6tZtDL8t
Why do the heat engine manufacturers seek for new materials, coatings that can withstand even higher temperatures than the available ones do? Please explain from the 2nd law of thermodynamics point of view.
Stainless steel ball bearings (r = 8085 kg/m3, k =15.1 W/m·°C, cp = 0.480 kJ/kg·°C, and a = 3.91 * 10-6 m2/s) having a diameter of 1.2 cm are to be quenched in water. The balls leave the oven at a uniform temperature of 900°C and are exposed to air at 30°C for a while before they are dropped into the water. If the temperature of the balls is not to fall below 850°C prior to quenching and the heat transfer coefficient in the air is 125 W/m2·°C, determine how long they can stand in the air before being dropped into the water.
a power plant steam, steam is continuously extractedfromthe turbine and in a heat exchanger there is a condensation of the extracted steam. The energy released during condensation of steam is used to operate a heat engine. A heat engine receives thermal energy at a rate of 1200 kJ/hr from condensing steam and rejects waste heat to a lake at 20°C at a rate of 800 kJ/hr. Determine the lowest possible condensing steam temperature.
5.) By traveling through a bass tube, 2.5 cm O.D. and 2.2 cm I.D., which is surrounded by steam at 55 kPa and 90% quality, 9.4 kg/s of water is heated from 15oC to 60oC. Assume the inside unit convective coefficient is 2000 W/m2-K, and the outside unit convective coefficient is 7950 W/m2-K. Determine (a) the length of tube required; (b) the steam supply in kg/h if no subcooling occurs.
750 kg of dry saturated steam at a pressure of 160 N/cm2 is generated in a boiler per hour. The temperature of feed water is 28°C and the steam from the boiler enters the super heater after a heat loss of 690 kJ/kg, where it is superheated such that the degree of superheat is 250°C. Determine i) Dryness fraction of the steam at the entry point of the super heater ii) Heat absorbed per hour in the super heater iii) Total heat supplied to the inlet water in the boiler
A thermal plant utilizes 125 gallons of 28oAPI fuel at 26oC in 24 hours while the power guarantee for the same period amounts to 2300 kW-hrs. Determine the thermal efficiency of the plant.
A rotary dryer fired with bunker oil having HHV = 10, 000 kcal/kg is to produce 20 MT/hr of dried sand with 0.5% moisture from wet feed containing 7% moisture. Specific heat of sand is 0.21 BTU/lb-°F. Temperature of wet sand is 30 °C and temperature of dried product is 115 °C. If the heater requirement, Qh = 2, 500 kW, calculate the density of bunker oil in kg per m3 ifspecific gravity of bunker oil is 0.8 and dryer efficiency is 70%.
) Stainless steel ball bearings (ρ = 8085 kg/m3and cp = 0.480 kJ/kgC) having adiameter of 1.22 cm are to be quenched in water at a rate of 1402 per minute.The balls leave the oven at a uniform temperature of 900C and are exposed to air at 300C for a while before they are dropped into the water. If thetemperature of the balls drops to 855C prior to quenching, determine:(i) The rate of heat transfer from the balls to the air; and(ii) The rate of entropy generation due to heat loss from the balls to the air.
H6. An air conditioner in an upper-floor apartment unit is turned on during a hot summer afternoon. If heat can be removed from the interior at a rate of 1.5 kW, estimate the time required to cool the air inside the apartment to its final temperature. Your estimate should create any needed input data and should incorporate factors like the size of the apartment and the behavior of air.
Termodynamic question I NEED ANSWER RARIDLY PLEASE!!! Water vapor enters the steam turbine at 4000 kPa pressure, 500 ° C temperature and 6 m3 / h volume flow, shown in the figure below. 0.2 times the mass flow rate of the incoming water comes out of the outlet no. 2 with 500 kPa pressure and 200 ° C temperature. 0.8 times the mass flow rate of the water comes out of the outlet no.3 with 30 kPa pressure and 0.85 dryness degree. Since the heat transfer from the turbine to the environment is 5000 kW, Find the mass flow rate of the incoming water. Find the volume flow of water at outlet no. 3. Find the power (kW) produced by the turbine. (Changes in kinetic and potential energies are negligible)