The heating element of a water heater in an apartment building has a maximum power output of 34 kW. Four residents of the building take showers at the same time, and each receives heated water at a volume flow rate of 14x10-5 m³/s. If the water going into the heater has a temperature of 17°C, what is the maximum possible temperature of the hot water that each showering resident receives? Number Units eTextbook and Media

The heating element of a water heater in an apartment building has a maximum power output of 34 kW. Four residents of the building take showers at the same time, and each receives heated water at a volume flow rate of 14x10-5 m³/s. If the water going into the heater has a temperature of 17°C, what is the maximum possible temperature of the hot water that each showering resident receives? Number Units eTextbook and Media

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter2: The Kinetic Theory Of Gases

Section: Chapter Questions

Problem 25P: A company advertises that it delivers helium at a gauge pressure of 1.72107 Pa in a cylinder of...

See similar textbooks

Similar questions

Explain how the maximum possible heat transferrate Q.max in a heat exchanger can be determined when themass flow rates, specific heats, and the inlet temperatures ofthe two fluids are specified. Does the value of Q.max dependon the type of the heat exchanger?
A counter-flow double-pipe heat exchanger is to heat water from 20°C to80°C at a rate of 1.2 kg/s. The heating is to be accomplishedby geothermal water available at 160°C at a mass flow rate of 2 kg/s. Theinner tube is thin-walled and has a diameter of 1.5 cm. The overall heat transfercoefficient of the heat exchanger is 640 W/m2?K. Using the effectiveness–NTUmethod, determine the length of the heat exchanger required to achieve thedesired heating.
A test is conducted to determine the overall heat transfer coefficient in anautomotive radiator that is a compact cross-flow water-to-air heat exchangerwith both fluids (air and water) unmixed. The radiator has 40 tubesof internal diameter 0.5 cm and length 65 cm in a closely spaced plate-finnedmatrix. Hot water enters the tubes at 90°C at a rate of 0.6 kg/s and leaves at65°C. Air flows across the radiator through the interfin spaces and is heatedfrom 20°C to 40°C. Determine the overall heat transfer coefficient Ui of thisradiator based on the inner surface area of the tubes.
Solar radiation is incident on a 5 m2 solar absorberplate surface at a rate of 800 W/m2. Ninety-three percent ofthe solar radiation is absorbed by the absorber plate, whilethe remaining 7 percent is reflected away. The solar absorberplate has a surface temperature of 40°C with an emissivityof 0.9 that experiences radiation exchange with the surroundingtemperature of -5°C. In addition, convective heat transferoccurs between the absorber plate surface and the ambientair of 20°C with a convection heat transfer coefficient of7 W/m2∙K. Determine the efficiency of the solar absorber,which is defined as the ratio of the usable heat collected bythe absorber to the incident solar radiation on the absorber.
Lake Erie contains roughly 4.00 ✕ 1011 m3 of water. How much energy is required to raise the temperature of that volume of water from 18.0°C to 21.0°C? How many years would it take to supply this amount of energy by using the 1,400-MW exhaust energy of an electric power plant?
What is the maximum possible coeffcient of performance of a heat pumpthat brings energy from outdoors at -10:00C into a 25C house?
An inventor claims to have invented an adiabaticsteady-flow device with a single inlet–outlet that produces230 kW when expanding 1 kg/s of air from 1200 kPa and300C to 100 kPa. Is this claim valid?
Long cylindrical AISI stainless steel rods (k =7.74 Btu/h·ft·°F and a = 0.135 ft2/h) of 4-in-diameter are heattreated by drawing them at a velocity of 7 ft/min through a21-ft-long oven maintained at 1700°F. The heat transfer coefficientin the oven is 20 Btu/h·ft2·°F. If the rods enter the ovenat 70°F, determine their centerline temperature when theyleave. Solve this problem using analytical one-term approximationmethod (not the Heisler charts).
a solid block of iron at 220 C is set on the floor of a foundry at 35 C. What will the block's temperature after sitting on the floor for 20 min? Given that the rate constants for iron in the situtaion is k = .054 min-1. Newtons law of cooling: dT/dt = -K (T-Ta) substitute y=T-Ta to make the equation separable.
An apparatus that liquefies helium is in a room maintained at 300 K. If the helium in the apparatus is at 4.0 K, what is the minimum ratio Qto/Qfrom, where Qto is the energy delivered as heat to the room and Qfrom is the energy removed as heat from the helium?
A 50-m-long section of a steam pipe whose outer diameteris 10 cm passes through an open space at 15°C. The averagetemperature of the outer surface of the pipe is measured to be150°C. If the combined heat transfer coefficient on the outer surfaceof the pipe is 20 W/m2·K, determine (a) the rate of heat lossfrom the steam pipe; (b) the annual cost of this energy lost if steamis generated in a natural gas furnace that has an efficiency of 75percent and the price of natural gas is $0.52/therm (1 therm =105,500 kJ); and (c) the thickness of fiberglass insulation(k = 0.035 W/m·K) needed in order to save 90 percent of the heatlost. Assume the pipe temperature to remain constant at 150°C.
One ton of liquid water at 80C is brought into awell-insulated and well-sealed 4-m * 5-m * 7-m room initiallyat 22C and 100 kPa. Assuming constant specific heatsfor both air and water at room temperature, determine (a) thefinal equilibrium temperature in the room and (b) the totalentropy change during this process, in kJ/K.