Answered: What is the input force? (b) What…

Engineering

Mechanical Engineering

What is the input force? (b) What is the distance through which the input piston moves?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Related questions

Q: Solve the following problem :a.What is the weight of a 1-kg mass at an altitude where the local…

A: Given data, m= 1 kg g= 9.75 m/s² Note: for part b, complete data is not given.

Q: A crate of mass 75kg is pushed along a floor with a force of 26N for a distance of 7 m. Calculate…

A: Find the work done .

Q: A lO-kN car and 5-kN hoist are supported 1.8 m above the floor by a cylinder with a 300-mm bore .…

A: Total force acting on the cylinder,F=10+5=15kN=15000N Area of the bore of the cylinder,A=π/4*(d^2)…

Q: An object, m1 with a mass of 10.0 kg placed on a frictionless, horizontal table. It is connected to…

A: The free-body diagram of the above system is drawn below. Here, N, a, and T represent the normal…

Q: In a car service station, a force of 100 N is required to raise the car on the hydraulic lift. If…

A: Given ThatF=100Nr-radius of pistonD-diameter of hydraulic Lift20D=rso10r=rm=? ****Please Note that…

Q: A set of 20 stairs, each of 20 cm height, is ascended by a 700 N man in a period of 1.25 s.…

A: Write the given data:

Q: Air, at 25 kPa gauge and 25oC, is contained in a tank that has a volume of 0.05 m3. The barometric…

Q: What is the net force on a ball of mass 20kg and volume of 0.3 m3 when it is submerged under water?

A: Given data, Mass = 20 kg V=0.3 m³ Fluid is water, So density =d=1000 kg/m³

Q: Spiderman, whose mass is 75.0 kg, is dangling on the free end of a L = 11.5-m-long rope, the other…

A: Given, Mass of Spiderman m = 75 kg Length of rope L = 11.5 m θ = 59.3o

Q: n electric motor driven conveyor belt is required to take 2,200 pounds of dirt, rocks per minute…

A: Given Mass, m = 2200 pounds Height, h = 15 ft Time, t = 1 min = 60 sec Find Power, P

Q: What is non-impulsive forces?

A: An impulsive force can be defined as the very large force acting for an infinitesimally short period…

Q: A weightlifter raises a 150-kg barbell from the floor to a height of 2.2 m in 0.80 s. What is his…

Q: . How much work is done in forcing 50 ft3 of water through a 0.5-inch pipe if the difference in…

Q: lever is used to lift a heavy load. When a 25 N force pushes one end of the lever down 1.8 m, the…

Q: ** Please label the question answers so I could understand it better! Thank you! Scenario: A chair…

Q: the force output of a cylinder when extending can be calculated by multiplying the pressure times

A: given: the force output of a cylinder when extending can be calculated by multiplying the pressure…

Q: circular cylinder of 20 cm diameter and 120 cm long contains watr up to a height of 80 cm. It is…

Q: A closed cylinder of diameter 30 cm and height of 20 cm is completely filled with water. Calculate…

Q: A block of wood of 2m x 1m x 1m x in size and specific gravity of 0.75 is floating in water. What is…

Q: Calculate the force exerted by a 125 lbm average human under normal Earth gravity. Provide answers…

A: Solution Given data Mass=125 lbm

Q: A hydraulic press has an input cylinder 1 inch in diameter and an output cylinder 6 inches in…

A: Given, Input Cylinder diameter, D1=1 inch. Output cylinder diameter, D2=6 inch. Force on the input…

Q: A piano mover rolls a 200 kg piano at constant speed up a ramp 2m long at an angle of 30 degrees…

A: Given, Mass of the piano , M = 200kg. Length of the inclined , L = 2m. Angle of inclination = 30…

Q: You are using a wheel and axle as a simple machine. You applied a force of 30 lb to the rim of the…

A: Given data Diameter of wheel (D) = 3 ft = 3*12 in. = 36 in. Diameter of axle (d) = 4 inch Applied…

Q: A ship with vertical sides near the water line, weighs 40 MN and draws 6.7 m in salt water (specific…

A: Given data, Weight of the ship with ballasts, Wwith = 40 MN Weight of the ballast, Wb = 2 MN SO,…

Q: tank that weighs 5kg is filled with 3 liquids shown below. What is the force at the bottom of the…

A: It is required to determine force at bottom of tank

Q: A gas is under pressure of 22.028 bar abs at 420C. Compute the constant R in m2/s2K if it has a unit…

Q: mechanic is lifting a car of 2000kg using a screw jack as he applies a force of 100 N. The screw…

A: Given:m=2000 kgF=100 Nl=600 mmp=10 mm

Q: A mechanic is lifting a car of 2000kg using a screw jack as he applies a force of 100 N. The screw…

Q: *** A force of 75N is applied to a nutcracker to crack open a walnut. If the MA of the nutcracker is…

A: Given:Finput=75 NM.A.=5

Q: A 80 m high vertical column of a fluid of density 1600 kg/m3 exists in a place where g = 9.88 m/s2.…

A: given data- height of the column h = 80m density of the fluid ρ =1600 kg/cu.m g = 9.88 m/s2 to…

Q: a. Compare the size of the force placed on your bicep muscle to the force of the 20 lb dumbbell…

A: The weight of the dumbbell is given by, Consider some essential dimensions.

Q: Water in a cylinder of height 9 ft and radius 2 ft is to be pumped out. The density of water is 62.4…

A: Answer: The work required if (a) The tank is full of water and the water is to be pumped over the…

Q: 2. Some of the first power-generating wind turbines were small, having blades with a radius of 8.00…

A: Given data: - The blade radius of the small wind turbine is r = 8.00 m. The large radius of the…

Q: A 490-kg block is resting on a 53 deg inclined plane with a coefficient of friction = 0.44. Find the…

Q: On a square plank 10cm thick and weighing 10kg, a 50-kg man stands. What is the smallest possible…

A: According to Archimedes' principle, when an object is fully or partially submerged in fluid, its…

Q: Calculate the weight of a 6.6-lbm wood on a planet where the acceleration due to gravity is 10 m/s²?

A: Given Data⇒ Mass of wood(m)=6.6 lbm Acceleration due to gravity g=10ms2

Q: The component of the force along the inclined plane due to mass of the body on a inclined plane is…

A: Given data: Component of the weight of the body along the inclined plane, Fx = 500 N. The net force…

Q: A horizontal force P acts on the top of the 30 N block having a width of 25 cm and a height of 50…

A: Given: W=30 N w= 25 cm h=50 cm μ = 0.33

Q: A rectangular plate is submerged half in oil with a Gs = 0.8 and hald in water such that its top…

Q: 1. Write in detail about working of any one hydraulic system application in construction area with…

Q: What is the Gravitational Potential at position 1 for mB? Answer: Check What is the Potential Energy…

Q: The forearm shown below is positioned at an angle θ with respect to the upper arm, and a 5.0-kg mass…

Q: storage vessel for gasoline (sg=0.68) is a vertical cylinder 0.5 m in diameter. If it is filled to…

A: Given Data S=0.68 D=0.5 m H=39 cm

Q: The piston of a 60° twin V-engine has strokes of 126 mm. The connecting rods driving a common crank…

Q: an air cylinder has a bore of 25 mm and is operated with shop air at a pressure of 6.327 kg/cm2 .…

A: Given data: d=25 mmp=6.327 kg/cm2 Need to determine the push force exerted by the piston rod.

Q: The hydraulic lift in a car repair shop has an actual mechanical advantage of 6.5. How much force…

A: Given Data Output force=1500 lb Mechanical advantage=6.5

Q: A force of 30 N is applied to the input piston of a hydraulic jack. If the input and output piston…

Q: 4. A car weighing 20 kN rounds a curve of 50 meter radius banked at an angle of 25°. Find the…

Q: If you know the direction of the weight force, will you know the direction of the normal force?

A: Given: Normal force is N Weight force is W

Q: A conical tank of top radius 4 ft and height 4 ft is filled with oil of weight density equal to ρ.…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

The input and output pistons of a hydraulic car lift have diameters of 3.00 in and 25.0 in, respectively. A 2890 lb car is raised through a height of 5.00 ft above the garage floor.

(a) What is the input force?

(b) What is the distance through which the input piston moves?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The input piston and output plunger of a hydraulic car lift at the same level, as shown in the drawing. The cross-sectional area of the input piston is 12cm^2, while that of the output plunger is 1200cm^2. The force F1 is applied to the input piston had a magnitude of 150 N. What is the weight W of the car? Neglect the weight of the piston and plunger.
In a car service station, a force of 100 N is required to raise the car on the hydraulic lift. If the diameter of the hydraulic lift is 20 times as the radius of the piston where the force must be applied, what is the mass of the car to be lifted?
A force of 30 N is applied to the input piston of a hydraulic jack. If the input and output piston have areas of 0.2 m² and 0.8 m², respectively, what is the minimum weight that can be lifted by the jack?
The diameter of the small cylinder of a hydraulic press is 6 inches while the diameter of its large piston is 10 inches. If a 140 lb. of force is applied at the small piston and neglecting friction, what is the force on the large piston.
In a hydraulic press, the small cylinder has the diameter of 8 cm while the larger piston has thediameter of 22 cm. If the force of 600 N is applied to the small piston, what is the force on thelarger piston, neglecting friction?
A 500kg bucket is lifted by a crane at a certain position shown below. What is the magnitude of the force that is exerted on the hydraulic piston?
A hydraulic jack is used to raise a 10KN car. A force of 400N applied on a 25mm diameter jack plunger. What diameter of jack in mm is required to raise the car?
The small piston of a hydraulic lift has a cross-sectional area of 4.6 cm2 and its large piston has a cross-sectional area of 392.2 cm2. What force must you apply to the small piston for the elevator to carry a load of 12.6 kN?
A pudding truck carries pudding with a density of 67.55 lb/ft! in a horizontal cylindrical tank with a diameter of 6 ft. Find the force exerted by the milk on one end of the tank when the tank is half full.
If you know the direction of the weight force, will you know the direction of the normal force?
Problem 2.- The small piston of a hydraulic lift (Fig. 3) has a cross-sectional area of 3.00 cm2 and its large piston has a cross-sectional area of 200 cm2 What force of magnitude F1 must be applied downwards to the small piston in order to lift a load whose weight is Fg = 15.0 KN?
A 300 cc solid weigh 180 grams in water and 240 grams in water and 240 grams in oil whose relative density or specific gravity is 83, Find a) the weight of the solid b) the density of the solid c) the loss of weight in water (Buoyant force in water) d) the loss of weigh-in oil (Buoyant force in oil)