The internal side of a wall is kept at 100o C and its external side which is exposed to the surrounding is kept at 10oC. The heat transfer convective coefficient of the surrounding is 10 W/m2oC. The wall conductivity coefficient is 1.3 W/mo C and its thickness is 0.4 m. What is the heat transfer through the wall?

The internal side of a wall is kept at 100o C and its external side which is exposed to the surrounding is kept at 10oC. The heat transfer convective coefficient of the surrounding is 10 W/m2oC. The wall conductivity coefficient is 1.3 W/mo C and its thickness is 0.4 m. What is the heat transfer through the wall?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.1P: A plane wall, 7.5 cm thick, generates heat internally at the rate of 105 W/m3. One side of the wall...

See similar textbooks

Similar questions

1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
2.55 A long, 1-cm-diameter electric copper cable is embedded in the center of a 25-cm-square concrete block. If the outside temperature of the concrete is 25oC and the rate of electrical energy dissipation in the cable is 150 W per meter length, determine temperatures at the outer surface and at the center of the cable.
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
1.37 Mild steel nails were driven through a solid wood wall consisting of two layers, each 2.5-cm thick, for reinforcement. If the total cross-sectional area of the nails is 0.5% of the wall area, determine the unit thermal conductance of the composite wall and the percent of the total heat flow that passes through the nails when the temperature difference across the wall is 25°C. Neglect contact resistance between the wood layers.
A high-speed computer is located in a temperature-controlled room at 26C. When the machine is operating, its internal heat generation rate is estimated to be 800 W. The external surface temperature of the computer is to be maintained below 85C. The heat transfer coefficient for the surface of the computer is estimated to be 10W/m2K. What surface area would be necessary to assure safe operation of this machine? Comment on ways to reduce this area.
A plane wall, 7.5 cm thick, generates heat internally at the rate of 105 W/m3. One side of the wall is insulated, and the other side is exposed to an environment at 90C. The convection heat transfer coefficient between the wall and the environment is 500 W/m2 K. If the thermal conductivity of the wall is 12 W/m K, calculate the maximum temperature in the wall.
One surface of the plane wall with a thickness of 25 cm and a heat transfer coefficient of 15 W / mK is kept at 90 C, while the other surface is in contact with the air. The temperature of the air is 20 ºC and the heat transfer coefficient in the environment is 25 W / m2K. Find the temperature of the surface in contact with the air.
It is measured that a 2-m2 wall has a heat transfer rate of 7200 W. If the thickness of the wall is 0.02-m and the temperature difference on either side of the wall is 60ºC, determine the thermal conductivity in W/m K.
The heat loss per hour through 1 sq. ft of furnace wall 18" thick is 520 Btu. The temperature on the hot side of the wall is 1900 degrees F, and its average thermal conductivity is 0.61 Btu/hr-ft-°F. Determine the temperature on the other side of the wall in °C.
The average rate at which energy is conducted outward through the ground surface in North America is 54.0 mW/m2, and the average thermal conductivity of the near surface rocks is 2.50 W/m K. Assuming a surface temperature of 10.0oC, find the temperature at a depth of 10.0 km. Ignore the heat generated by the presence of radioactive elements.
Answer this ASAP,thx An empty sphere is made of aluminum (k = 202 W/m. °C) with an inner diameter of 4 cm and an outer diameter of 8 cm. The inside temperature is 100°C and If the ball above is coated with an insulating material having k = 50 mW/m. °C 1 cm thick. The outside of this insulation is in contact with an environment having h = 20 W/m.°C and Ts = 10°C, calculate the heat transfer under these conditions.