The lap joint is fastened with four 4/5 in-diameter rivets. The working normal stress for the plates is 30 kis, shearing for the rivets is 42 ksi and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. Include the necessary FBDs showing the involved internal forces in the exploraty sections. Your solurions are invalidated without the required FBDs. in.

The lap joint is fastened with four 4/5 in-diameter rivets. The working normal stress for the plates is 30 kis, shearing for the rivets is 42 ksi and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. Include the necessary FBDs showing the involved internal forces in the exploraty sections. Your solurions are invalidated without the required FBDs. in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.6.9P: A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial...

See similar textbooks

Similar questions

While drilling a hole with a brace and bit, you exert a downward force P = 25 lb on the handle of the brace (see figure). The diameter of the crank arm is d = 7/16 in. and it s lateral offset is b = 4-7/8 in. Determine the maximum tensile and compressive stresses e1, and e2respectively, in the crank.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A solid bar of circular cross section (diameter d) has a hole of diameter d/5 drilled laterally through the center of the bar (sec figure). The allowable average tensile stress on the net cross section of the bar is s allow. (a) Obtain a formula for the allowable load P allowthat the bar can carry in tension. (b) calculate the value of P allowif the bar is made of brass with a diameter d = 1.75 in. and s allow= 12 ksi. Hint: Use the formulas of Case 15. Appendix E.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A steel column (E = 30 x 103 ksi) with pinned ends is constructed of a W10 x 60 wide-flange shape (sec figure). The column is 24 ft long. The resultant of the axial loads acting on the column is a force P acting with an eccentricity n = 2.0 in. If P = 120 kips, determine the maximum compressive stress ff^ in the column. Determine the allowable load Pallowif the yield stress is ( y =42 ksi and the factor of safety with respect to yielding of the material is n = 2.5.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends. Find i lie maximum shear, ion si le. and compressive stresses in the tube and their corresponding strains. Assume that G = 6000 ksi.
A vertical pole of aluminum is fixed at the base and pulled at the top by a cable having a tensile force T(see figure). The cable is attached at the outer edge of a stiffened cover plate on top of the pole and makes an angle a = 20° at the point of attachment. The pole has length a = 2.5 m and a hollow circular cross section with an outer diameter d2= 280 mm and inner diameter d1= 220 mm. The circular cover plate has diameter 1.5d2 Determine the allowable tensile force Tallow in the cable if the allowable compressive stress in the aluminum pole is 90 MPa.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.