Question [2] The truss in the figure below is supporting a 70 kN load applied at joint A and 90 kN at joint B. You are required to: Determine the reactions at the supports. Determine the force in each member of the truss. For the determined forces in part b), state if the members are in tension or compression. D A 70 kN 2 m- B 90 KN 1.5 m

Question [2] The truss in the figure below is supporting a 70 kN load applied at joint A and 90 kN at joint B. You are required to: Determine the reactions at the supports. Determine the force in each member of the truss. For the determined forces in part b), state if the members are in tension or compression. D A 70 kN 2 m- B 90 KN 1.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A prismatic bar AE of negligible weight is hinged to a vertical wall at A and supported by a strut BD as shown in Fig. 1. Find the reaction induced at A and B through the action of a sphere of weight W tied by a string CF that is parallel to AE. Also, find the tension in the string. The radius of the sphere is such that the points B and C are at the same level. Assume W = 1000 lb.05:54 PM
A chandelier weighing 20kg hangs from a point B by two strings AB and BC. AB is inclined at 50° to the horizontal and BC at 35° to the vertical as shown. Question 7A, determine the force in the string AB. Question 7B, determine the force in string BC. See figure from the preceding problem.
Question 1) in FIG loading condition is given beam F force F = 65 kN , first distributed load W 1 = 41 kN / m , w 2 distributed load w 2 = 51 kN / m , θ angle θ = 48 ° and L length of L = 5 m . According to this; Question 1-A) B at the point y direction ( B y ) Determine the support reactions. (Enter yourresultwithout writing kN units.) Question 1-B) to the point in y direction ( A y ) Determine the support reactions. ( Enter yourresult without writing kN units.) Question 1-C) to the point in x direction ( A x ) Determine the support reactions. ( Enter yourresult without writing kN units.)
In the figure shown, there is an armature that is supported by a cable and a simple support at B. In addition, this armature rests on a spring with a constant as indicated in the figure. By applying the loads shown at points H and L, the spring is compressed by 10 cm.Determine:a) The reactions in the support at B and the tension in the cable AD.b) The force in the element I - K by the method of sections (determine if the element is in tension or compression)
Given the figure below (a) determine the reaction at A vertical (b) reaction at C vertical and C horizontal (c) bar force at AB (d) bar force at BD.
Question 1Two bars ABC and CD are connected at joint C. Bar ABC is pinned-supported at A while bar DC is pinned-supported at joint D as shown in the Figure Q1. Determine:(a) The reaction forces at joints A and D(b) The resultant force at joint A and its direction(c) The internal loadings at the midpoint of member BC
a)Consider the cable supporting the hook, and thus the load. The magnitude of the internal force within the "left-piece" of the cable at 1.25m above the sheave is _____ kN. b) Consider the cable supporting the hook, and thus the load. The state of the internal force within the "left-piece" of the cable at 1.25m above the sheave is _____ . NOTE: Enter "1" for "tension". Enter "2" for "compression" Enter "3" for "torsion" Enter "4" for "neither tension, nor compression, nor torsion c)Consider the cable between the input power sheave and the Sheave-G. The magnitude of the internal force within this cable at 1.667m from the center of Sheave-G is _____ kN. d) Consider the cable between the input power sheave and the Sheave-G. The state of the internal force within this cable at 1.667m from the center of Sheave-G is _____ . NOTE: Enter "1" for "tension". Enter "2" for "compression" Enter "3" for "torsion" Enter "4" for "neither tension, nor compression, nor torsion e) The state of the…
A circular column is made of concrete [Ec = 4.2(103)ksi] while being reinforced with six steel rods [Est = 29 (103)ksi]. It is acted uponby an axial force of 30 kip as shown in the figure to the right. Each rod has a diameter of 0.85 in. Find the forces in each steel rod, concrete, stress in each steel rod and concrete.
A bar of square cross-section is subjected to point loads of P1, P2, P3, and P4 as shown here. Find the magnitude of the force P3 necessary for the equilibrium, if P1= 130 kN, P2 = 230 kN & P4 = 180 kN. Also, determine the stresses in each section & the net change in the length of steel bar, where the respective side of a square and lengths are d1=55mm, L1=31 cm, d2 = 40mm, L2=38 cm, d3=55 mm & L3 =30 cm. Take E = 185 GPa. The force P3 to make it to equilibrium in kN is The Stress in section 1 in N/mm2 is The Stress in section 2 in N/mm2 is The Stress in section 3 in N/mm2 is and The total change in length in x10-3 mm is
A transmission cable 300 m long, weighs 600 kg. The tensions at the ends of the cable are 400 kg and 450 kg. Find the distance of its lowest point to the ground. Choices: 150m ,153m , 148m , 145m
A bar is composed of a section of aluminum rigidly joined between the sections of steel and bronze, as shown in the Figure. Axial loads are applied at positions indicated. If P = 3000 lb and the cross-sectional area of the rod is 0.5 in^2 , determine the effort in each section. The figure is in the attached image.
For the structure below indicate: a) What is the tension in cable BE? Consider P=792.1 kN.( Indicate the answer in kN.) b) What is the tension in cable CF. (Indicate the answer in kN.) c) What is the value of the reaction at D? (Indicate the answer in kN.)